New Circuits Products

FPGA Technology supports reconfigurable computing.

Hardware solution, based on SGIÃ-® Reconfigurable Application-Specific Computing (RASC(TM)) technology, achieves scalability and bandwidth required for data-intensive applications. Available as add-in module, solution operates with IntelÃ-® ItaniumÃ-® 2 processor-based servers and visualization systems. RASC solution set can connect multiple RASC expansion modules into one...

Mobile VoIP Processor is designed for Wi-Fi-® phones.

Suited for Wi-Fi phones with multimedia and telephony capabilities, BCM1161 integrates ARM9(TM)-based CPU, analog voice codec with direct microphone and speaker interface, as well as interfaces for 262k color LCD display and USB 2.0. Single-chip solution provides polyphonic ring-tone support, 2 Megapixel digital camera, voice record/playback capabilities, and video clip record/playback ability....

USB-UART Bridge has highly integrated design.

Requiring 2 external decoupling capacitors for minimal configuration, FT232R includes onboard EEPROM, master clock generator, 3.3 V LDO regulator, reset generator, and USB termination resistors. Integrated device features 5 I/O pins that can be configured in EEPROM to have several functions, including output clock. In addition to full set of modem control signals, each device has variety of...

Integrated Circuits suit time-sensitive applications.

ToP (Timing-over-Packet) devices ZL(TM)30301 and ZL30302 transmit timing and synchronization over asynchronous packet switched networks. Both devices maintain average frequency accuracy of under Ã-

Custom Knob Solutions - Maximum Grip and Comfort

To learn more about the different types of knobs available or which ones to select for your specific application, download this product guide.

DC/DC Controller powers UltraSPARC-® and SPARC-® processors.

Offering 45 A single-chip solution, PolyPhaseÃ-® synchronous step-down controller, Model LTC3819, features 4 integrated MOSFET drivers and on-board 5-bit digital interface. Core voltage is from 1.025-1.4125 V in 12.5 mV steps and core current ranges from 15-40 A. Housed in 10-pin MSOP package, device operates at up to 90% efficiency from input voltage of 4.5-36 V, and includes current...

Photoflash Capacitor Charger comes in 3 x 3 mm DFN package.

Featuring complete photoflash capacitor charger and IGBT driver, LT3485-3, -0, -2, and -1 photoflash capacitor charger ICs operate from 1.8-10 V range and have primary current limits of 2, 1.4, 1, and 0.7 A respectively. Control technique allows series to use 5.8 x 5.8 x 3 mm transformers, and no external components are required to set output voltage. While charging, output proportional to...

Controller enables X-by-Wire technology for vehicle networks.

Delivering 10 Mbps over 2 channels, application-specific FlexRay(TM) MB88121 provides fault-tolerant, deterministic data transmission, suitable for engine control, braking, and steering subsystems. It can be connected directly to existing CPUs and complements standard automotive buses, including CAN and LIN. Internal speeds reach 80 MHz with 4, 5, 8, or 10 MHz external oscillator, or by external...

Chipset targets battery-operated products.

Suited for PDAs, mobile phones, and GPS applications, ANTARIS(TM) 4 offers tracking sensitivity of -158 dBm. With power consumption of 62 mW during 1 Hz update rate in Continuous Tracking Mode, baseband Model ATR0621 is enabled by 0.18 um CMOS technology, while RF-front end IC Model ATR0601 is enabled by BiCMOS technology. Chipset's 16-channel engine features u-blox SuperSense(TM)-enabled indoor...

VoIP Chip suits analog telephone adapters.

VoIP chip with integrated software and hardware reference design, Tulip AC494 ATA, is targeted for OEMs seeking to add VoIP capabilities to products. Basic configuration integrates two 10/100 baseT Ethernet ports, 1-4 VoIP ports, and 2 two FXS analog interfaces. It supports various configurations of FXS and FXO ports using pin and software compatible devices from Legerity's VE880 VoicePort(TM)...

Power Supply Tracker enables control of dc/dc modules.

Designed for modules or power supplies with or without access to feedback pins, Model LTC2926 enables variety of power up and power down profiles and supports up to 2 slave supplies that track master signal. Tracking of up to 2 dc/dc modules is achieved with N-channel MOSFETs in series with power path, and 2 integrated remote sense switches automatically compensate for voltage drop across...

Don't Let Your Money Drain Down the Hole...Drill Steel with Euroboor

As a globally recognized manufacturer of industrial grade portable tools, Euroboor is at the forefront of drilling and cutting technology. Our reputation as an industry leader is built on robust products that fit a wide range of industrial cutting and drilling applications. See our video to learn more about all of our quality products.