Circuits

ICs suit automotive tire pressure monitoring systems.

Combining ATA5756 and ATA5757 RF transmitters with ATmega AVR 8-bit Flash microcontroller, Model ATA6285 and ATA6286 ICs control and transmit data gained from capacitive pressure and motion sensors. Operating from -40 to 125Â-ºC, single-package devices feature temperature sensor with shut-down mode, and 90 kHz slow-oscillation mode for timer wake-up in sleep mode. Devices consume 0.5 Â-µA...

Read More »

Energy Meter ICs utilize intelligent battery technology.

Comprised of 4 models in 64-lead LQFPs, single-chip ADE7100 and ADE7500 families are based on ADE energy measurement core and combine microprocessor, on-chip Flash, LCD driver, real-time clock, and intelligent battery management circuitry. Solid-state, failure-resistant devices consume as little as 1.2 Â-µA and enable services such as remote meter-reading, time-of-use billing, and load...

Read More »

Three-Phase Motor Drivers include built-in PWM circuits.

Models TPD4104K, TPD4111K, and TPD4112K drivers feature 3-phase full-bridge distribution circuit with level-shift type high-side driver and low-side driver, output IGBT, and FRD. Intended for DC brushless motors, air conditioner fans, and pump motors, 250 and 500 V single chip drivers include protective functions for overcurrent, overheating, and power supply voltage drop. Lead-free and...

Read More »

Graphics Controller is used for vehicle navigation systems.

Designed for vehicle dashboard applications, Model MB86297 supports 2D and 3D functions as well as fogging and lighting for 3D effects. Max power consumption is less than 2.3 W and 2 digital RGB display output channels have resolutions ranging from 320 x 240 to 1,280 x 1,024. Including 64-bit DDR memory bus rated at 266 Mbps, unit is capable of drawing up to 10 mil polygons/sec and can render 250...

Read More »

Power Supply IC is suited for automotive airbag applications.

Manufactured in high-voltage 0.8-Â-µm BCD technology, Model ATA6264 provides measures against undervoltage conditions and battery cable loss, power sequencing, integrated watchdog, and other diagnostic/monitoring functions. Unit handles voltage supply with programmable voltage levels and communication with microcontroller is carried out via 16-bit SPI. Voltage supply section of...

Read More »

Ethernet PHY features low power, high ESD design.

Housed in 5 x 5 mm QFN package, KSZ8041NL consumes 150 mW with ESD ratings of 6 kV. Fast Ethernet transceiver chip is suited for applications with space constraints, where low power is important, or where stringent ESD conditions apply such as in Industrial Ethernet environments.

Read More »

Video Amplifier suits FTTH triplexers.

Designed to amplify incoming signals in fiber-to-the-home analog video networking applications, TAT6254 Single Family Unit Video Receiver/Amplifier integrates trans-impedance amplification and post amplification on single chip and operates on single 12 V supply. It delivers automatic gain control to maintain constant 21 dBmV/channel output from -8 to +2 dBm. Unit features high gain levels over 32...

Read More »

ESD Protection ICs target high-definition video market.

With 0.6 pF ultra-low line capacitance, HDMIULC6-4SC6 monolithic, application-specific IC allows High Definition Multimedia Interface (HDMI) to operate at speeds of 1.65 Gbit/s and even up to 3.2 Gbit/s, with full 15 kV contact and air Electrostatic Discharge (ESD) protection. It features greater than 5 GHz bandwidth, cut-off frequency of 5.3 GHz, 0.015 pF impedance matching, 0.5 Â-µA maximum...

Read More »

Linear Regulator comes in 1.6 x 1.6 mm 6-pin MLF-® package.

With dropout of 40 mV at 150 mA, model MIC5301 ultra-low dropout(ULDO(TM)) linear regulator optimizes battery life for portable applications powered by Li-ion battery. LDO offers more than 75 dB power supply rejection ratio (PSRR), and bypass pin provides noise filtering for higher PSRR applications. Operational from -40 to 125Â-ºC, device features 1 Â-µF ceramic capacitor, 30 Â-µsec...

Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Sponsored

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.

Read More »

All Topics