Hayward Flow Control

Injection Valves and Quills withstand corrosive environments.
Fluid & Gas Flow Equipment

Injection Valves and Quills withstand corrosive environments.

Suited for chemical dosing systems, IV Series Injection Valves and IQ Series Injection Quills are available in range of thermoplastic body materials, including PVC, CPVC, and PVDF for corrosion resistance. Units feature chemical resistant, spring-loaded check valves and MNPT threaded end connections to match any process requirement. Offered in sizes from -½–1 in., products are also suitable...

Read More »
Butterfly Valves target commercial swimming pools.
Fluid & Gas Flow Equipment

Butterfly Valves target commercial swimming pools.

Available in 2-8 in. sizes, PoolMaster(TM) Valves feature PVC body and disc with EPDM liner. Units are immune to electrolytic and galvanic corrosion, and contain no byproducts that can leach out and contaminate water and other sensitive fluids. One-piece body incorporates fully supported flanged bolt holes to prevent stressing of mating pipe flanges, while blowout-proof 316 SS shaft and full body...

Read More »
Agricultural & Farming Products

Bus Controller suits piping systems with automated valves.

Used in piping systems with 8 or more electrically or pneumatically actuated valves, Bus Control System allows all actuators in system to be controlled by PLC with one pair of wires. Actuators are daisy chained on same pair of wires, with each actuator assigned unique address for identification by PLC. Only designated actuator has ability to read and act on control instructions. In addition to...

Read More »
Automated Ball Valves feature all-plastic construction.
Fluid & Gas Flow Equipment

Automated Ball Valves feature all-plastic construction.

Rated for full 225 psi, fully repairable EA Series has true union design and incorporates 110 Vac electric actuator with output torque of 140 lb-in. Built-in, automatic resetting thermal overload protector prevents motor burnout, and 25% duty cycle motor drives valve through permanently lubricated gear train. Featuring EPDM seals and PTFE seats, PVC valve is available in sizes for -½-2 in....

Read More »
Pneumatic Actuators provide automatic valve control.
Mechanical Power Transmission

Pneumatic Actuators provide automatic valve control.

Featuring 4-piston rack and pinion design, Series PCD and PCS work with range of all-plastic, corrosion-resistant ball and butterfly valves, from -¼ in. ball valves up to 24 in. butterfly valves. Torque outputs range from 60-15,800 lb-in. with minimum inlet air pressure of 80 psi. Double-acting Series PCD requires air pressure for both open and close cycles, while Series PCS utilizes mechanical...

Read More »
Filtration System filters process fluid within tank.
Electronic Components & Devices

Filtration System filters process fluid within tank.

In-Tank Filtration System comes with 50 micron filter cartridge made of corrosion-resistant CPVC with FPM seals for chemical resistance. Single and double filter cartridge models are available, both with choice of WEBSTER(TM) brand Series D or S pumps, which are seal-less and can be run dry. Replacement cartridges are available in 1, 5, 10, 30, 75, and 100 micron ratings with 1 in. ID and 12-½...

Read More »
Check Valve minimizes pressure drop.
Fluid & Gas Flow Equipment

Check Valve minimizes pressure drop.

Cepex Wafer Check Valves prevent reversal of flow in piping systems, protecting pumps, filters, and other process equipment. With straight through design, products operate without requiring adjustments or settings and will not stick, jam, or fail due to rust or corrosion. Valves, available to fit 4, 6, or 8 in. pipelines, feature PVC construction with flanged connections and choice of EPDM or FPM...

Read More »
Multi-Port Ball Valve simplifies piping connections.
Fluid & Gas Flow Equipment

Multi-Port Ball Valve simplifies piping connections.

Plastic, lateral, 3-way ball valves replace conventional valve/tee connection combinations as well as zero dead-leg valves in piping system layouts. Available in sizes from -½-6 in., products can be made of PVC or CPVC with choice of FPM or EPDM seals. Integral ball permits flow to be diverted from center port to left or right ports without shutoff position. Valves feature one-piece molded body...

Read More »
Injection Valves and Quills withstand corrosive environments.
Fluid & Gas Flow Equipment

Injection Valves and Quills withstand corrosive environments.

Suited for chemical dosing systems, IV Series Injection Valves and IQ Series Injection Quills are available in range of thermoplastic body materials, including PVC, CPVC, and PVDF for corrosion resistance. Units feature chemical resistant, spring-loaded check valves and MNPT threaded end connections to match any process requirement. Offered in sizes from -½–1 in., products are also suitable...

Read More »
Company News

Hayward Flow Control Now Down Under !

Clemmons, NC – Hayward Flow Control is very pleased to announce that effective March 3, 2015, Hayward Flow Control has expanded into the Hayward Australia facility located in Dandenong South, Victoria. This main facility currently houses the Hayward Australia Pool group. This facility will now also headquarter the following Flow Control activities for Australia New Zealand: • Sales and...

Read More »
Company News

Expands Canadian Presence

Clemmons, NC- – Hayward Flow Control is proud to announce the expansion of its operations and presence in Canada. Effective January 1, 2014, Hayward Flow Control will be operating from the Hayward Canada facility, located in Oakville, Ontario. The 200,000 ft-² warehouse and office facility currently houses the Hayward Canada Residential and Commercial Divisions. This facility will now also...

Read More »
Butterfly Valves target commercial swimming pools.
Fluid & Gas Flow Equipment

Butterfly Valves target commercial swimming pools.

Available in 2-8 in. sizes, PoolMaster(TM) Valves feature PVC body and disc with EPDM liner. Units are immune to electrolytic and galvanic corrosion, and contain no byproducts that can leach out and contaminate water and other sensitive fluids. One-piece body incorporates fully supported flanged bolt holes to prevent stressing of mating pipe flanges, while blowout-proof 316 SS shaft and full body...

Read More »
Company News

New Hayward Industrial Product Guide Provides Detailed Look at Company's Wide Range of Plastic Flow Control Products

Hayward Flow Control Systems, Clemmons, NC, a division of Hayward Industrial Products, has announced availability of a new 4/c Industrial Product Guide on their wide range of plastic flow control products. This comprehensive new resource provides a brief overview of Hayward engineering, manufacturing, quality, and support capabilities along with sections on the company's extensive line of ball...

Read More »
Company News

Newly Redesigned Hayward Web Site Offers Easy-To-Navigate Look at Company's Extensive Line of Plastic Flow Control Products

Hayward Flow Control Systems, Clemmons, NC, a division of Hayward Industrial Products, has announced activation of their newly redesigned web site at www.haywardflowcontrol.com. The new user-friendly, easy-to-navigate site features a brief corporate overview of the company along with Product Quick Links to the company's extensive line of ball valves, butterfly valves, check valves, control...

Read More »
Agricultural & Farming Products

Bus Controller suits piping systems with automated valves.

Used in piping systems with 8 or more electrically or pneumatically actuated valves, Bus Control System allows all actuators in system to be controlled by PLC with one pair of wires. Actuators are daisy chained on same pair of wires, with each actuator assigned unique address for identification by PLC. Only designated actuator has ability to read and act on control instructions. In addition to...

Read More »
Automated Ball Valves feature all-plastic construction.
Fluid & Gas Flow Equipment

Automated Ball Valves feature all-plastic construction.

Rated for full 225 psi, fully repairable EA Series has true union design and incorporates 110 Vac electric actuator with output torque of 140 lb-in. Built-in, automatic resetting thermal overload protector prevents motor burnout, and 25% duty cycle motor drives valve through permanently lubricated gear train. Featuring EPDM seals and PTFE seats, PVC valve is available in sizes for -½-2 in....

Read More »
Pneumatic Actuators provide automatic valve control.
Mechanical Power Transmission

Pneumatic Actuators provide automatic valve control.

Featuring 4-piston rack and pinion design, Series PCD and PCS work with range of all-plastic, corrosion-resistant ball and butterfly valves, from -¼ in. ball valves up to 24 in. butterfly valves. Torque outputs range from 60-15,800 lb-in. with minimum inlet air pressure of 80 psi. Double-acting Series PCD requires air pressure for both open and close cycles, while Series PCS utilizes mechanical...

Read More »

All Topics