FCI Electronics
Etters, PA 17319
Share:
Backplane Connector is designed as SATA drive interface.
Featuring staggered contact lengths, 22-position, vertical backplane receptacle connectors enable implementation of Serial ATA (SATA) HDD interface. Molded guide posts and self aligning design facilitate hot plugging and blind mating of HDDs. Seven contacts that comprise SATA port support differential signaling, initially at speeds of 1.5 Gbps, and power segment of SATA backplane receptacle uses...
Read More »
Backplane Connector System uses co-planar connectors.
AirMax VSÃ-® uses air as dielectric between adjacent conductors. Insert Molded Leadframe Assembly enables same connector to be used for differential pair signals, single ended signals, or power. AirMax VS allows for any allocation of signals within one connector so systems can grow from 2.5-25 Gb/s without requiring redesign. Two-piece header-receptacle is available in 150- and 120-position...
Read More »
Backplane Receptacle Connectors support speeds of 3 Gbps.
Vertical, 29-position Connectors enable implementation of Serial Attached SCSI hard disk drive interface. Staggered contact lengths provide sequential mating of contacts to enable hot plugging. Molded guide posts feature angled lead-in to compensate for connector misalignment, allowing device plug and backplane receptacle to self align during mating process. Options are available for through-hole...
Read More »
Plug Connectors provide 200 or 296 signal contacts.
GIG-Array 13 mm Mezzanine Connectors add capability for 18 or 28 mm board-to-board spacing when used with 5 or 15 mm receptacles. Units support transmission rates of 10 Gbps, and differential pairs nominally provide 100 ohms matched impedance. Connectors with 296 positions contain 37 columns with 8 individual signal contacts and 9 ground contacts in each column, while 200-position connectors...
Read More »
Right-Angled Receptacle provides ATCA Zone 3 interconnection.
When combined with existing right-angled header, AirMax VSÃ-® Virtual Shield receptacle creates complete coplanar interconnect for Advanced TCA(TM) Zone 3. Composed of 10 insert molded leadframe assembly columns, 150-position connector provides 5 differential signal pairs. Supporting custom interconnects between main card and direct mate rear transition module, mated pair offers signal line...
Read More »
USB Connectors provide additional power contacts.
USB+Power connectors combine standard USB contacts with additional power contacts to address applications where power requirements exceed capabilities of standard USB. Configuration provides additional 3 A of current-carrying capacity beyond 1 A supported by standard USB. Active latch provides positive retention to board-mounted receptacle for secure connection. Receptacles are available in...
Read More »
Connector Modules each offer voltage rating of 150 V.
MetralÃ-® High Power Modules are right-angle daughtercard connectors with 1 x 2 or 2 x 2 contact configurations per 12 mm module and total current-carrying capacity of 80 A. Contacts are flat except for minimal forming at plug connector's mating interfaces, which enables use of high conductivity base metal. Airflow passages in insulating connector bodies allow air to flow through fully mated...
Read More »
Backplane Connector offers design flexibility.
Offered with 3 and 2 mm column spacing in 150- and 120-position configurations, AirMax VSÃ-® 2-piece header-receptacle connector system allows for allocation of signals within connector. Insert molded leadframe assembly enables same connector to be used for differential pair signals, single ended signals, or power. Enabling systems to grow from 2.5-25 Gbps, part accommodates 63 differential...
Read More »
Card Edge Connectors facilitate PCI Express signaling.
Card Edge Connectors enable implementation of high-speed serial PCI Express signaling to riser cards in rack-mount servers. Series 10037901 is keyed to accept standard PCI Express x8 add-in card or 280-position riser card that can support PCI, PCI-X, or PCI Express add-in cards. Series 10027747 is keyed to accept 3-slot riser that provides two x8 PCI Express slots supporting x4 links and one...
Read More »
Retention Mechanism protects graphics card.
Board-level retention mechanism for PCI Express graphics cards protects against electrical interrupts and mechanical damage caused by system-level shocks and vibration. Flexible arm extends away from slot and includes molded post that snaps into notch on bottom of add-in card. Device solders to motherboard adjacent to x16 PCI Express card edge connector, and engages with hockey stick shaped hook...
Read More »