AntsSoft
Shanghai 201102 CHN
Share:
Workholding System works with VMCs.
Made of precision ground cast iron, Foundation workholding system is customized for each vertical machining center. It incorporates alpha-numeric labeling system to simplify building and cataloging of fixtures. Each hole within 50 mm grid pattern has 12 mm bushing for accurate location and M12 thread for bolt down. Holes are sealed with chip plugs preventing build up of chips.
Read More »Forklift Trucks handle up to 3 tons.
Electric FBC15K - FBC30K cushion tire forklift series has capacity of 3,000 to 6,000 lb. Series has energy efficient hydraulic system, transistorized drive controller, proportional regenerative braking, and interactive LED display. Regenerative braking automatically engages when accelerator pedal is released. LED display shows battery state of charge, error codes and truck status, and can be used...
Read More »Walk-Behind Scrubber cleans floors.
Encore L26HD has power forward and reverse; large solution and recovery tanks for longer stay time on floor between cleanups; and two heavy-duty brush drive motors. Parabolic break-away squeegee allows blade changes without tools. Solution and brushes turn off when machine is not moving. All electrical circuits offer breaker protection. Palm pressure controls provide safety against operator...
Read More »Floor Scrubber provides walk-behind cleaning.
Encore L26 Cylindrical Brush Scrubber cleans grouted surfaces, rough concrete, textured slate, marble, raised rubber disk, and slip-resistant applications of silicate carbide. It has 26 in. dual rotary brush floating scrub deck that cleans deep into grout or multi-surface floors, and recovers debris left on floor while scrubbing. Pre-sweeping is not necessary. Machine's 20 gal solution and...
Read More »Carpet Extractors clean with steam.
Portable BEXT series of on-board hot water extractors heat water at spray tip to 212 deg F. Compact and lightweight, equipment is easy to load and transport in multi-story buildings on both carpeted areas and multiple surfaces. It has high pressure injection with choice of 300 or 150 psi water pump; industrial three-stage vacuum motor; stainless steel wand; and 15-foot, crush-proof vacuum and...
Read More »Tank Mixers offer various drive configurations.
DT top-entering, sealed tank mixers offer modular design to facilitate any application. They are available from 1/4 to 5 hp with speeds up to 1750 rpm. Units operate using direct or gear-reduced drives. Right angle drives are optional. Various shaft lengths and diameters are available, as well as range of impeller selections. Seal options include V-ring/lip seal, stuffing box, and single or...
Read More »Travel Carriage holds torch in flat and vertical positions.
BUG-GY-VERT welding travel carriage uses 14.4 V rechargeable battery and magnetic base to hold torch. Guide arms track and steer into fillet joint; rail is not required to operate machine. Torch oscillator allows unit to perform weave welds. BUG-GY-VERT provides constant travel rate and precise path control.
Read More »Edgecard Connectors are approved by UL and CSA.
Edgecard connector series for 0.093 in. daughtercards are appropriate for backplane wiring or any application requiring circuit connection of motherboard to daughterboards. Provided in vertical-mount, extender-card, and right-angle bend configurations, connectors are available with gold-plated, 3 A contacts, ranging from 05/10 to 80/160. Double-row devices are made with high-temperature materials...
Read More »Cobalt-Steel Drill speeds stainless-steel production.
Made of M35 cobalt steel with TINAL FUTURA TOP coating, VA INOX drill combines aggressive point geometry and flute profile to provide cutting edges with high load bearing capacity. It is 4 times more productive than conventional HSS drills, is suitable for small to medium batch sizes typical in stainless-steel production, and does not require internal coolant supply.
Read More »Divider/Feeder provides representative samples.
PT 100 Sample Divider ensures that sample represents entire bulk instead of random samples taken out of buckets with spatulas or spoons. Rotating rifflers spilt up to 5 L of inhomogeneous samples with wide particle size distribution into 6, 8, or 10 representative sub-samples. DR 100 Vibratory Feeder ensures that divider is centered over inlet hopper for no-loss feeding. Feed rate is controlled...
Read More »