Argosim
Saint-Martin-d'Hères 38400 FRA
Share:
Epoxy Adhesive cures at low temperatures.
TRA-BOND 400-5 thixotropic one-part epoxy system is used as a no-sag, non-drip staking and laminating adhesive. It combines properties of moderate working life with ability to cure at temperatures as low as 60Ã-
Read More »Table Base has adjustable height.
100/40 HTE System cantilever table base is ANSI-BIFMA-approved and adjusts from 23 in. to 31 in. with retractable, telescoping crank handle. Front-mounted crank has 6:1 ratio, offering 1 in. of rise for every 6 turns of the handle. 14 gauge steel upright tubing and 16 gauge cross tubing offer table rating of 200 lbs dynamic. Table base is available in widths ranging from 30 in. to 72 in. and...
Read More »
Temperature Control System applies sealants and plastisols.
Integrated Metering and Temperature Control System ensures that robot-applied, single-component sealants or plastisols are applied at controlled flow rate and pre-set temperature. System controls material temperature and dispenses material at variable flow rates according to commands from servo drive. Fully automated for production applications, control system communicates with robots through its...
Read More »
Epoxy provides clear lamination.
TRA-BOND 2119 low-viscosity epoxy is designed for bonding to glass, plastics and ceramics. It is a high Tg, high lap shear material with room temperature cure. Semi-rigid upon cure, it is suitable for bonding between dissimilar substrates. Applications include small potting, laminating and bonding of optics and electronics.
Read More »
Polymeric Membranes filter caustic and acidic chemicals.
Polymeric PCI tubular membranes incorporate proprietary polymeric substrates that allow them to withstand solutions with pH values from 1 to 14 at high processing temperatures. Caustic and acid-resistant membranes can suit filtration requirements covering nanofiltration and ultrafiltration spectrums. Resistant to solvents, membranes are used to separate one liquid into two streams: concentrate...
Read More »
Transmitters are available in 14 units.
LPI-SERIES isolated loop powered transmitters feature field programmable bi-polar input ranges with 2 kV isolation and accuracy of 0.10%. Members include: DC to DC with fixed or programmable input range, Bridge to DC, Resistance to DC, Potentiometer to DC, Differential RTD to DC, RTD to DC with fixed or programmable ranges, Thermocouple to DC with fixed or programmable ranges, AC to DC with...
Read More »
Proportional Valves feature close tolerance spools.
DFW proportional, directional control valves can be used for reproducible control of actuator speed in rapid/slow speed profiling as well as smooth acceleration and deceleration. D1FW features flow rating to 12.5 gpm, while D3FW has flow rating to 45 gpm. Connection options include conduit boxes with wire leads, flying leads or DIN-type connectors.
Read More »
Cal-Gas Standards Generator calibrates gas analyzers.
Model 491MB Gas Standards Generator is designed to calibrate gas analyzers such as gas chromatographs, mass spectrometers, and ion mobility spectrometers. 491MB uses Trace Source(TM) Permeation Tubes to generate low concentrations (1000 ppm to ppb) gas standards for VOCs, Acid Gases, Amines, Sulfurs, and Hydrocarbons (400+ compounds). Standards are traceable to NIST.
Read More »
Sensors measure micro liquid flow rates.
Rated for operation up to 500 psig, Series 102 liquid flow sensors measure flow rates from 13 mL/min to 10 L/min (2.6 GPM) with Ã-
Read More »
Continuous Solvent Vapor Monitors reduce exhaust airflow.
670 Series Continuous Solvent Vapor Monitors are placed at source of emissions. Continuous monitoring allows air recirculation in processes to reduce exhaust airflow. Incinerator has less air to process, therefore requires less fuel. Additionally, 670 Series meets safety standards set by NFPA to protect incinerator as well as employees.
Read More »