Thinspace Technology Inc
Port Orange, FL 32128
Share:
Epoxy Adhesive fixes electrical coils.
Tra-Bond CA20 thixotropic epoxy adhesive system is formulated for shorted turns, damaged end wire extensions, or other coil repair applications where high-fill, non-sag adhesive is needed. It provides high dielectric isolation and good mechanical strength. Readily mixed, handled, used, and cured at room temperature, Tra-Bond CA20 develops strong bonds to materials such as metals, glass, ceramics,...
Read More »
Nail Packs include enough fuel to finish nailing.
Cordless TrimMaster 18(TM) is available with fuel and fastener packs that contain 2,000 nails and 2 fuel cells. Fuel cells contain precise amount of fuel needed to deploy all nails in pack. Packs are available in fastener sizes of 5/8, 1, 1-1/4, 1-1/2 and 2 inches.
Read More »
CompactPCI System diagnoses remote system status.
CP-ASM7-P47-RIO has Intelligent Platform Management Interface (IPMI), making it suitable for installation in remote locations or harsh environments. It continuously monitors system status, reports potential problems, and facilitates remote diagnosis of system status and component failures. System provides power supply redundancy, full hot swap capability, and up to 4 power supplies. It has...
Read More »AC Drive controls motors up to 3.7 kW.
PowerFlex 4 is available in power ratings from 0.2 to 3.7 kW and in voltage classes of 115, 230 and 480 volts. It features integral keypad with local potentiometer for control. RS485 communications make drive compatible with DriveExplorer and DriveExecutive software when using serial converter module. Drive is available in IP20 package that can be DIN rail or panel mounted. Zero Stacking(TM)...
Read More »
Microdrives deliver constant and variable torque.
MC 4X stainless steel enclosed microdrives use external heatsinks for natural convection cooling. Models range in power from fractional to 20 HP and voltages are 240, 480, and 590 Vac. Features include 4 pre-set speeds; 2 skip speeds with adjustable bandwidth; PID setpoint control for temperature, pressure, and flow; and either Modbus or Metasys serial communication protocol. Control board has...
Read More »
Laser Focusing Lenses have focal lengths from 1 to 20 in.
ZnSe focusing lenses are suitable for use as direct replacements or original equipment in industrial CO2 laser systems from Amada, Cincinnati, Mazak and Mitsubishi. They are available in 0.6 to 2 in. dia, and in plano convex, concave and meniscus shapes. Optimized for 10.6 Ã-µm radiation, lenses are available with focal lengths from 1 to 20 in. in 0.1 in. increments. Applications include...
Read More »
Hand Tools work on electrical wiring.
Electrical Assembly Tools perform specific electrical applications such as winding motors and cores, preparing leads, and fabricating wiring harnesses. Each has rubber cushion hand grips for comfort and light touch return springs. Tools include Model 440 for slitting PVC jacketing on coaxial cable; Model 501 for cutting and stripping wire from 10 to 26 AWG; Model 9180 for cutting Kevlar in fiber...
Read More »
RF Drying System improves insulation production.
Macrowave applies radio waves at 40.68 MHz to remove water from fiberglass batting, board and vermiculite, and prevents migration of aqueous binders. It works on webs up to 12 ft wide. Because water is more responsive to RF energy than most materials, moist areas absorb more RF power than dry areas, which results in uniform drying. Method promotes consistent drying regardless of non-uniform...
Read More »
Capillary Columns work at high temperatures.
ValcoBondÃ-® Capillary Columns operate at high temperature limits to enhance column bake out, reducing sample carryover and cycle times. Liquid phase processing produces low bleed characteristics while maintaining retention characteristics identical to standard phases. Processes can be combined with automated deactivation, coating, curing, bonding and crosslinking.
Read More »
High-Impulse Hoses handle abrasive applications.
Type 482TC and 482ST hoses have high-Nitrile inner tube for fluid compatibility, single braid of high-tensile steel wire reinforcement, and tough cover for abrasive applications requiring SAE l00R1 Type AT or EN853 Type ISN hose lines. Both are available in sizes from 1/4 to 1 in. ID. Their no-skive construction eliminates need to remove hose cover before crimping.
Read More »