Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Machine Vision Software runs on Pentium-® PC and Windows-®
Enhancements to DT Vision Foundry(TM) v3.5 include bar code, networking, script, and image matching functions. Data Matrix Tool analyzes 2D bar codes in 360Ã-
Read More »Test and Measurement Software uses graphical operation.
DT Measure Foundry(TM) 3.0 utilizes drag-and-drop functionality to let users arrange desired instrument functions and select measurement source. It offers software developer's kit, 200 built-in math functions, and software that incorporates OPC-compliant devices. Its Formula Evaluator tool allows users to combine information from data and control channels into one formula. Software support for...
Read More »
CompactPCI 32-bit SBC offers flexible I/O.
P4 Samurai single board computer (SBC), available with P4 processors ranging from 1.2 to 2 GHz, has full hot swap capability. Featuring universal PCI to PCI bridge chip and adaptive I/O routing scheme, SBC handles jobs that previously required multiple computers. P4 processor incorporates 512 kbytes on-die L2 cache, and P4 Samurai board accommodates up to 512 Mbytes of soldered DDR-RAM-266....
Read More »Software Module tracks industrial cutting tools.
BACKTRACK Tool & Die Tracking helps manufacturers move, store, and maintain tool and die equipment throughout its life cycle. It manages hundreds of printing plates and dies in three locations in networked environment. Hand held personal data terminals (PDTs) are used to check dies in and out of storage and control their movement. Software generates bar codes to keep records up to date, and...
Read More »Circuit Breakers are rated from .5 to 25 amps.
UL 489 is DIN rail mountable, only 13 mm wide, and designed to standard industrial control trip curves. Unit is used for branch circuit protection and comes in single and 2-pole version.
Read More »
Diode provides fast/soft recovery.
Stealth(TM) 1200 V diode is designed for switch mode power supply, motor drive, uninterruptible power supply, welding power, and induction heating applications. It combines fast/soft recovery switching with low reverse recovery current to reduce switching transistor turn-on losses in hard-switched applications. Diode is available in single and dual packaged configurations in TO-220 and TO-247...
Read More »
Garbage Cart holds 335 lb of waste.
Rotationally-molded BossKart(TM) has pleated panels in sidewall for vertical strength and to allow cart to recover quickly from squeeze of fully automated collection system. Extra deep latch bar pocket ensures secure hook up with lift systems. Cart has 12 in. molded HDPE wheels, 3/4 in. plated, solid steel axles, and molded-in scuff rails on base. Foot-tilt area allows easy access to axle for...
Read More »
Parallel Shaft Gearboxes have increased torque capacity.
Models SK 1282 through SK 5382 Clincher(TM) gearboxes have 41% more torque than company's previous models, yet have no gear ratio or dimensional changes. Therefore, engineering revisions by customer are not required to use increased capacity units. Gearboxes are available in 5 case sizes, all with 97% efficiency. Options include torque up to 28,320 lb-in.; power from 0.16 to 30 hp; output speeds...
Read More »
Digital to LVDT Converter has accuracy of -
Two-Channel 14-bit series accepts 14-bit offset binary or two's complement digital input, and converts it into two 0-7 V RMS outputs at 3 KHz. Output load is 2000 Ohms minimum. Other output voltages and frequencies are available. Part no. DLVDT314A-7-1 requires two's complement digital input, 7 V RMS reference input, and +5 V @ 1 ma, +15 V @ 25 ma, -15 V @ 25 ma maximum. Operating temperature...
Read More »CNCs suit common to complex applications.
PC-based Axium Power CNCs include wide range of digital drives and motors. ARS (Advanced Resonance Suppression) provides intelligent compensation for imperfections in stiffness and elasticity of machine by increasing feedback loop gain. Power panel runs under Windows(TM) 2000. Remote diagnostic, unattended CNC system back-up, or fully remote system operation is possible via Ethernet connection...
Read More »