Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Software was developed utilizing .Net technology.
PLC WorkShop for Siemens S5 - Performance Series provides full 32-bit Windows application featuring NT security, floating and docking toolbars, open tree view programming, and context-sensitive help. Programming is strengthened via use of mnemonics, merge blocks, and cutting and pasting by block or element. Software enables 1-step transfer of logic from offline to PLC, and built-in SCADA...
Read More »Miniature Slide Switches suit variety of PCB applications.
Miniature SPDT EG1260 series features 2 optional SMT mounting configurations and 3 slide actuator sizes. Designed with electrical life of 10,000 cycles, products are rated at 0.3 A @ 4 Vdc. Designed with chamfered locating pins, dimensions are 0.106 x .264 x 0.055 in. Actuation force is rated at 150 g Ã-
Read More »
Modular Pay-Off handles fine and very fine wire.
Motorized Payoff utilizes low-stress, French Curve unwind path and accommodates fine wire materials from .006-.050 in. diameter. It features snag detection sensor and shutdown signal output, controlled back tension for precise control of any downstream straightening process, as well as built-in loop control reservoir for up to 4 ft of pulled wire. Accommodating up to 60 lb of material, payoff can...
Read More »
UTP Cables extend video and data transmission.
BrillianceÃ-® VideoTwist(TM) Unshielded Twisted Pair (UTP) Cables deliver video and data in plenum and riser versions over distances of 1,300 ft and beyond depending on transmission equipment. VideoTwist Nanoskew(TM) 7987P and 7987R are suited for video-only transmissions, while other models suit component video, data, and KVM applications. With bonded-pair construction, VideoTwist 7988 and...
Read More »
Wireless I/O Communication System suits Division 1 areas.
XANT explosion-proof I/O transmitter/receiver system features impact-resistant, cast aluminum enclosure that houses transmitter. System utilizes spread spectrum frequency hopping techniques to provide interference-free link between remote devices and control room. In-plant range is 600-1,000 ft with no line-of-sight. Capable of carrying one 4-20 mA analog signal, system features 1 W transmitter...
Read More »
Grinding Wheels have vitrified bond structure.
Designed to work on tough metals and non-ferrous materials, Vitrified Super Abrasive Grinding Wheels include vitrified bonded CBN, PCD/PCBN, and diamond grinding wheel configurations. Tailored grinding wheels can be matched to unique specifications.
Read More »
Lighting Control offers bi-level switching of HID fixtures.
Model DM-105-WP features low voltage outdoor motion sensor, which uses passive infrared technology to detect occupancy. During times of vacancy, controller switches lights to lower level. When occupants return, lights immediately return to high. Bi-level switching capability eliminates long restrike time associated with ON/OFF control of HID lighting. Rated for outdoor use, sensor and controller...
Read More »
Awl Marker stores in handle of aviation snips.
Made of drop forged 8630 tool steel, Scratch Awl Marker is 3.5 in. in length tapering to sharp point. It is heat-treated with finely polished finish. Design allows sheet metal workers and other tradesmen to use awl for hole punching by striking on handle-less striking end.
Read More »
Skid Lifter offers 3,000 lb capacity and 32 in. lift height.
Designed to pick up load on skid or open-bottom pallet, Skid Lifter transports load to workplace and raises it to working height using 2-speed manual pump. For loads less than 600 lb, unit shifts into Quick-Lift mode so forks can be raised 32 in. in just 18 strokes of steer handle. For heavier loads, unit shifts to Ergo-Lift mode, raising forks to full height in 55 strokes. Load stabilizers...
Read More »
Nickel Wires allow out-of-position welds.
StoodyÃ-® 625, 182, 82, and A grades of flux cored nickel wires achieve welds in vertical-up position. Available in both .045 and 1/16 in. diameter, wires are packaged on 33 lb wire baskets. Welders can choose between running 75% argon, 25% CO2, or straight CO2.
Read More »