Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Pressure Cell is suited for rheological studies.
Made of corrosion-resistant materials, High Pressure Cell (HPC) is suited for studying rheological properties of samples at pressurized conditions with full viscometry and limited oscillatory capabilities. Unit, which enables studies at temperatures from -20 to +300Ã-
Read More »Simulation Software optimizes plant performance.
UniSim(TM) includes UniSim Design Suite, which offers HYSYSÃ-® software, steady-state and dynamic simulation, design, performance monitoring, optimization, and business planning for processing plants. UniSim Operations Suite provides multi-function dynamic simulation to optimize operating capabilities and staff skills. UniSim Optimization Suite ensures responsiveness to changes in business...
Read More »Microcontroller features embedded programmable logic.
Fabricated using 130 nm CMOS technology, GreenFIELD STW21000 combines ARM926EJ-S MIPS RISC processor core, 16-Mbit on-chip eDRAM memory, eFPGA block, and range of analog and digital peripherals. Unit is available with on-chip multiple HDLC controllers, 10/100 Ethernet MACs, multi-channel serial port, and Power-On-Reset function. It is suited for feedforward and digital pre-distortion ratio...
Read More »Linear Actuators carry load over 50-300 mm stroke.
Accepting 12, 24, or 35 Vdc power, low noise dc Series MMP.LA-3 delivers up to 170 lb of force, and is available with stroke lengths of 50, 100, 200, 250, and 300 mm. Selection of output speeds are provided with gear ratios of 5:1, 10:1, 20:1, and 30:1. Lubricated for life, standard unit features built-in limit switches, non-rotating inner tube, aluminum outer tube, and corrosion resistance....
Read More »
Plastic Degating Tool separates molded parts.
Featuring blade tip that reaches 850-°F in less than 1 min, electric hot knife, Model WB-1, melts runner to separate molded part and leaves clean edge. Wooden handle stays cool because heating element is located under replaceable blade tip. Tool is 6-¾ in. long and weighs under 1 oz.
Read More »
Machine Vision Camera uses progressive scan technology.
To eliminate image jitter, IK-TF7A incorporates three 1/3 in. progressive scan CCDs in co-site sampling arrangement, which results in picture accuracy at resolutions to 1024 x 768 with no RGB shift. Variable-speed, electronic, 9-step shutter operates from 1/100-1/100,000 sec. Camera features readout speeds to 90 fps in partial scan mode, 30 fps full pixel independent readout, and one RS-232C port...
Read More »High-Voltage Amplifier is suited for MEMS actuators.
Designed for use with Model 9070 MEMS Engine Driver System, Model 2375 features 4 channels, each rated for 20 mA continuous current with 0.2 ohm output impedance and independent voltage monitor output for use in closed loop system. Amplifier can drive capacitive loads up to 200 pF while maintaining full power bandwidth, exceeding 5 kHz. Product is suited for MEMS comb drives, cantilevered beams,...
Read More »Power Amplifier has bandwidth of DC to 2.0 MHz.
Manufactured in compact, rack-mountable chassis, Model 2348 meets requirements for MEMS testing, transducer characterization, and pulse applications. Independent, buffered, voltage monitor output reduces output signal to 20:1 for 50 ohm inputs and 10:1 for inputs exceeding 1 Megohm. Continuous current of 750 mA is available at voltages up to 50 Vp-p, providing 18.75 W of ac or dc output power to...
Read More »
Miter Saws are offered with laser tracking system.
Laser Tracking System is available on 10 in. Model 4410L and 12 in. Model 5412L Dual Bevel Sliding Compound Miter Saws, as well as 12 in. Model 4212L Dual Bevel Compound Miter Saw. Projecting thin red line along blade's kerf, arbor-mounted laser is visible throughout cut and follows exact contours of workpiece. Laser eliminates additional switches and conserves battery power by actuating with...
Read More »System Model Software supports mobile mutlimedia.
Virtual Platform VPOM-V1030 uses C-code, graphical modeling, and transaction-based modeling to replicate functionality of TI's OMAPV1030 chipset in PC-based simulation. Functionality includes operation of ARM and DSP processors on chip, connectivity peripherals, and GSM/GPRS/EDGE peripherals. Able to support standard OSs and execute binary code that targets OMAPV1030 platform, software helps...
Read More »