Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Air Compressors operate at noise levels as low as 66 dba.
Series 1100e, 1500e, and 1800e are 15, 20, and 25 hp encapsulated compressors, available with variable speed drive that can adjust to changes in air demand. To minimize noise levels, air-end and motor are mounted on rubber isolators. Units also include insulated intake and exhaust louvers as well as fully insulated enclosure.
Read More »Brushless Servo Motors suit space-restricted applications.
Maintenance-free MUS Series is fitted with high flux density Neodymium Iron Boron magnets, reducing rotor inertia. Motors cover torque range from 380 W to 3.5 kW and feature torque-to-inertia ratio that promotes acceleration and dynamic responses. Design and location of thermal sensor eliminate risk of overheating and demagnetizing.
Read More »
Transport System floats rolls on compressed air.
Rollmaster II(TM) features Aero-CastersÃ-® inflated with standard shop air to float paper, plastic, sheet metal, and coil rolls. As little as 1 lb of push can move 1,000 lb load, and device provides nearly frictionless omni-directional movement for roll alignment in tight spaces. Unit reduces risk of strain injuries and operator fatigue, provides clean, static-free operation, and has no...
Read More »
Diaphragm Chuck has internal rotary union.
Model DPH-300I standard 3 in. dia (1 micron TIR) 6-jaw diaphragm chuck is designed with internal rotary union that keeps air feed tube stationary. This eliminates vibration of standard rotating tube and allows chuck to operate at speeds up to 15,000 rpm. Chucks are tooled with special jaws and stops to hard turn small fuel injection components.
Read More »
Compression Tool assembles variety of connectors.
Calibrated to assemble F-connectors and RCA connectors, OmniSeal(TM) 11 is suited for use in home theater, CATV, CCTV, satellite, and other VDV applications. It features lightweight composite body and extended, high-leverage handle that minimizes hand fatigue. Nesting fixture freely adjusts to accommodate variety of connectors, and no dies or posts need to be changed.
Read More »
Wall Plates feature durable Nylon design.
Combining rigid characteristics of thermoset with unbreakable characteristics of nylon, Wall Plates are intended for industrial, commercial, and residential applications. Units feature smooth gloss finish, slightly rounded corners, and slightly extended dimensions that cover oversized holes. Depth of 0.25 in. accommodates rework boxes. All single gang plates, along with decorator style plates up...
Read More »Etch Compound provides surface profile on old concrete.
Safer for use than hydrochloric or muriatic acid, low-odor Superior Safety Etch comes in gel form for optimal uniformity. Water-based, non-flammable product is non-ozone depleting and contains no Toxic/Hazardous Air Pollutants. Clean up is with soap and water or denatured alcohol. Superior Safety Etch covers 200-300 sq-ft/gal and is suitable for green and mature concrete, factory and warehouse...
Read More »Wall Perimeter Sealer facilitates cove applications.
Featuring 100% solids formulation, chemical-resistant Superior Cove Kit is designed for vertical application at floor-wall joints to produce sanitary perimeter seal. This structural epoxy mortar, packaged in pre-measured kits to cover 35 lineal feet (4 in. vertical and 2 ft horizontal at 1/8 in.), requires clean surface prepared via sand blasting, water blasting, or other mechanical means. Each...
Read More »
Self-Clinching Fasteners permanently join 2 metal sheets.
PEMÃ-® SpotFast(TM) fasteners create permanent flush-attachment connection without protrusions on either side. They can attach 2 metal sheets too thin to weld (as thin as .030 in.), fasten sheets of unequal thicknesses, or join dissimilar metals unable to be welded. RoHS-compliant, steel fasteners install smooth with top sheet and flush, sub-flush, or blind with bottom sheet. Rotational...
Read More »
Air Chuck/Tool Holder rotates up to 4,500 rpm.
Modified for spring clamp/air open, Model 350 consists of 3 in. diameter, 3-jaw Air Chuck mounted to BT-30 tool holder. Chuck assembly mounts in standard BT-30 vertical machining center and is actuated via coolant through spindle passage. Standard VMC can be used as vertical lathe with pallet on one side for automatic load/unload of work pieces.
Read More »