Aprima Medical Software, Inc

Vane Pump handles high-volatility fluids.
Fluid & Gas Flow Equipment

Vane Pump handles high-volatility fluids.

Magnatex® MPT Regenerative Turbine Vane Pump is a magnetically driven, sealless pump featuring a regenerative turbine vane impeller and rare earth Neodymium magnets for synchronous drive with no slippage. Close-coupled design eliminates alignment problems. Pump is capable of operation under 2 ft of static NPSH at line pressures up to 100 psi and flow rates of 2-3 gpm.

Read More »
Screener is designed for in-line operation.
Agricultural & Farming Products

Screener is designed for in-line operation.

Vibroscreen® Circular Vibratory Bag Dump Screener scalps bag scraps and oversized materials from manually dumped bulk materials while protecting operator and plant environment against dust contamination. Ambient air and dust from dumping activities is drawn onto exterior of 2 cartridge filters that derive vacuum from top-mounted exhaust fan. Screener is offered in 24, 30 and 40 in. diameters.

Read More »
Encoders feature digital ASIC technology.
Communication Systems & Equipment

Encoders feature digital ASIC technology.

Model 771 and 776 Thru-Bore Series Accu-Coders(TM) have bore sizes to 1.875 in. and are suitable for motor feedback, velocity, positioning and servo control applications. Model 771 mounts directly on NEMA C-Face motors and features C-Face mount on both sides. Model 776 is 1.36 in. deep and ideal for space restrictive applications. Encoder-on-a-chip design provides noise immunity necessary for...

Read More »
Oscillator features frequency range to 156.25 MHz.
Electronic Components & Devices

Oscillator features frequency range to 156.25 MHz.

F4100 Crystal Oscillator offers standby mode for lower power consumption. Miniature 3.3 V oscillator features operating temperature range of -10°C to 70°C. Frequency stability is +/-100 ppm for all conditions. Output symmetry is 40% to 60% at 1.65 V over entire frequency range of 125 to 156.25 MHz; input current is 60 mA maximum. Unit is suitable for Fibre Channel, SONET, ATM, microprocessor...

Read More »
Relay Assemblies are rated for 60 A loads.
Electrical Equipment & Systems

Relay Assemblies are rated for 60 A loads.

Solid State Relay Assemblies feature anodized aluminum heat sink to ensure reliability at rated power levels in ambient operating environment up to 40° C. Load-suppression diode and finger-safe covers are standard. Units accept controller inputs of 3.5 to 32 Vdc or 90 to 280 Vac. Load currents range from 0.02 to 60 Adc and load voltages range up to 400 Vdc. Relays have bipolar output with 4000 V...

Read More »
Male Connectors are designed for use in backplanes.
Construction Equipment and Supplies

Male Connectors are designed for use in backplanes.

Type D Vertical Male Connectors are 8+2-row x 25-position headers that provide up to 220 signal contacts evenly distributed on 2 mm grid. They are UL approved and comply with requirement of IEC 917 and IEC 61076-4-101 specifications. Featuring multipurpose center incorporating pre-alignment guides, connectors feature press-fit design for gas-tight connection to PC board and are available in a...

Read More »
Inserter/Extractor has hot stamping area.
Agricultural & Farming Products

Inserter/Extractor has hot stamping area.

LP-1107 Inserter/Extractor's positive locking feature ensures secure retention of printed circuit boards and protection of components, circuitry, and connectors. Roll pin configuration locks boards into position, eliminating vibrations and rattles while preventing stress on board and accidental release of cards from connectors. LP-1107 comes with mounting pins, and is available for 1/16 in. thick...

Read More »
Digital Weight Indicator is for new or existing systems.
Test & Measurement

Digital Weight Indicator is for new or existing systems.

Model 4215 indicator can connect to PC and graphical user interface. Front panel has 999,999 display, 6 smart pushbuttons, 2 buttons for displayed item and displayed units selection, tare, peak and hold reset, alternate display view, and print. All menu buttons have alternate functions for setup menus. Programmed operations include peak hold and tracking, math, function channels, and limits....

Read More »

All Topics