Aprima Medical Software, Inc

Precision Ground Insert has 3F geometry.
Construction Equipment and Supplies

Precision Ground Insert has 3F geometry.

Precision ground insert with 3F geometry for stainless steels, aluminum, high-temperature alloys and steels features periphery ground edges for accurate profiling and indexability. Additional features include light hones and positive geometry. Radii are available for light depths of cut and producing small corner radii. PVD grades offer layer of lubricity for reduced coefficient of friction....

Read More »
Hoses are ideal for half-bend radius applications.
Fluid & Gas Flow Equipment

Hoses are ideal for half-bend radius applications.

Models 351TC and 351ST abrasion-resistant hoses, designed for 1/2 SAE 100R1 minimum bend radius applications, are available with MSHA-accepted Tough Cover or Super Tough polymeric cover. Both offer 4,000 psi constant working pressure in sizes that range from 1/4 in. to 3/4 in. I.D. They are constructed of oil-resistant, Nitrile-based synthetic rubber tube, with 2 braids of high-tensile steel wire...

Read More »
Bending/Forming Machines make multiple bends in a single plane.
Food Processing & Preparation

Bending/Forming Machines make multiple bends in a single plane.

ET 95 vertical and horizontal press tube bending/forming machines can produce square, rectangular, U and compound shapes on round, square, rectangular and other profile tubing or flat and bar stock. They have bending tonnage of 14-58 tons and bend radii of 2 to 6 in. with tube diameters from 2.5 to 3 in. and wall dimensions from .035 up to 1 in. O.D. and .180 up to 3 in. O.D. Controls include...

Read More »
Large Crane handles rough terrain.
Material Handling & Storage

Large Crane handles rough terrain.

The 130 ton RT9000E crane provides mobility, maneuverability and pick-and-carry capabilities. It has a five section 42 to 160 ft boom that provides a 169 ft maximum tip height and 140 ft maximum radius with 3,770 lb capacity. Cab has tinted safety glass, armrest-mounted single-axis controllers, hot water heater, air fan, sliding side and rear windows, sliding skylight with electric wiper and...

Read More »
Motion Chip controls four axes at a time.
Agricultural & Farming Products

Motion Chip controls four axes at a time.

PCD-4541 4-axis motion control chip is for 2-phase unipolar or bipolar stepper motors. Sequence logic for full and half step modes is built-in, so it can output CW/CCW pulses or excitation signals directly to drive chips. Chip provides independent axis control, simultaneous start and stop of all axes, linear or S-curve acceleration and deceleration, speed change on the fly, idling pulse output...

Read More »
Cylinders are available with bore sizes from 3/4 to 8 in.
Construction Equipment and Supplies

Cylinders are available with bore sizes from 3/4 to 8 in.

Q6 Hydro-Line Cylinders come with pressure-energized nitrile rod seals and nonmetallic piston wear rings. Pre-lubricated from factory, cylinders are suitable for non-lubricated air service up to 250 psi. Q6 NFPA-interchangeable cylinders feature precision-machined aluminum end caps and self-aligning, externally removable rod cartridge assemblies. Hydraulic HQ6 tolerates pressures to 400 psi, and...

Read More »
Bridge Handles feature counter bored mounting holes.
Mechanical Components and Assemblies

Bridge Handles feature counter bored mounting holes.

Ergostyle® Bridge Handles are made from glass-fiber reinforced technopolymer plastic with black matte finish, while mounting holes are counter bored for socket cap screws and have technopolymer plastic cover caps available in variety of colors. Slight bend in handle distributes force on fingers during use. Resistant to solvents, oils, grease, and other chemical agents, handles are also...

Read More »
Cement Resurfacer dries in 24 hours.

Cement Resurfacer dries in 24 hours.

P-205 EASY-FIX thin pavement overlay repairs uneven concrete surfaces, and is suitable for permanent repairs to sidewalks, drives, aprons, docks, and ramps. Able to resist freeze/thaw cycles, it adheres to damp surfaces. De-icing salts and water will not penetrate it. Application is accomplished via broom for textured, concrete, gray, non-slip surface that dries in 24 hours.

Read More »
Parylene System modifies pressures and dwell times.

Parylene System modifies pressures and dwell times.

PDS-2060PC Parylene deposition system, with integrated personal computer for programmable control, allows users to establish and refine programs that direct each phase of Parylene coating cycles. System includes on-board personal computer, fold-out keyboard, flat-screen monitor, and printer that operate under Labview(TM) software. Proprietary software prompts users for each parameter from vacuum...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers