Aprima Medical Software, Inc
Carrollton, TX 75006
Stationary Platforms service trucks and tank cars.
Platforms with slide track mounted access equipment provide safe access and fall protection to tank/bulk trucks, tank cars, and hopper cars. It has 3 ft wide swing gates with 4 in. toe plate, and meets OSHA requirements. Fabricated slide track platforms are available from 6 to 60 ft long.Read More »
Hot Box safely heats eight 55 gallon drums.
Sahara horizontal Hot Box Model S8 uses steam up to 200 psig, and can reach temperatures up to 300 deg F. Constructed of 304 stainless steel, Hot Box replaces homemade hot rooms and band heaters. It provides 110 gallon spill-containment capacity. Alternative capacities, electric model, and carbon-steel construction are also available.Read More »
Accelerometer measures vibration on structures.
Ultra miniature ceramic shear accelerometer type 8778A500 offers 10 mV/g vibration measurement sensitivity, 0 to 500 g measuring range, and a -Read More »
Clear Polymer helps avoid indutrial battery breakdown.
UDEL(R) P-1700 transparent thermoplastic polymer exhibits resistance to moisture absorption, shock, and vibration. Heat deflection temperature is 345 deg F. Transparent, opaque, and glass-fiber reinforced grades of UDEL polysulfone can be used for injection molding into complex parts or extrusion into forms such as rod, film, sheet, profile, and tubing. UDEL polysulfone resin can also be...Read More »
Friction/Wear Material suits non-lubricated applications.
Polyamide-imide TORLON(R) 4435 PAI provides wear resistance in high-PV, 50,000 to 100,000 psi-ft/min applications. It also exhibits wear resistance in low-pressure, high-velocity conditions (125 psi and 800 ft/min) and high-pressure, low-velocity conditions (2,000 psi and 50 ft/min). Glass transition temperature allows parts to operate continuously at temperatures up to 260 deg C. Thermoplastic...Read More »
High-Temperature Resins suit critical electronics applications.
Flame-retardant AMODEL FR-4133, FR-6133 and FR-6145 polyphthalamide resins are useful in lead-free SMT soldering operations. They are available in hot-water-moldable base resins, 4000 and 6000, and 2 glass-reinforced levels, 33 and 45%, with heat distortion temperatures up to 300 deg C. Applications include connectors, chip capacitors, cell phone components, circuit breakers, contactors, relays,...Read More »
Torque Transducer mounts in-line to SAE or Metric flanges.
Non-contact, rotary Model RTC sensor transmits torque signal to RF receiver, delivering output of 0 to 10 V, proportional to torque, or optional 4 to 20 mA output. Operating range is 1,500 to 170,000 in.-lb, with running speeds up to 15,000 rpm, depending on range. RF telemetry package is induction-powered by stationary loop antenna coupled to power supply and receiver. Transmitter may be...Read More »
Relay Output Module clips onto microPLC.
RO108M attaches to side of Series T1-16S microPLC and can switch/control 100 to 240 Vac or 5 to 24 Vdc. Each T1-16S accommodates up to 5 relay output modules. TRO108M can be used wherever it is necessary to have relay contact switch ON/OFF in control circuit. It allows T1-16S to control, alarm, or monitor based on system conditions, including: Turn ON/OFF motors, solenoids, or interposing relays;...Read More »
Wastewater Evaporator eliminates discharge to drain or sewer.
HYDRO-VAP(TM) 1000E runs at 3 to 4 gph to provide 95% reduction in wastewater. Evaporator heats wastewater to boiling and turns it into vapor. Harmless water vapor is vented through blower-assisted stack and exhausted to outside atmosphere.Read More »
Parts Washer cleans with hot water.
Model 45E Aqueous Parts Washer cleans parts with hot water, biodegradable detergents, and high-flow nozzles. Parts are usually clean and ready for use in 10-15 min. As needed, its Wastewater Disposal System evaporates wastewater and can reduce waste stream up to 95%.Read More »