Aprima Medical Software, Inc

Vibratory Rollers compact soil with tons of force.
Material Handling & Storage

Vibratory Rollers compact soil with tons of force.

Single-drum Series C820C, C830C, and C850C have operating weights of 11,000 to 28,285 lb. Series C820C and C825C are smooth-drum models that are best suited for granular and mixed soil applications, while Series C822C padfoot units are most effective on cohesive materials. All have lockable control panel, back-up alarm, SAHR brakes, and adjustable operator's seat.

Read More »
High-Temperature Paint provides corrosion protection.
Paints & Coatings

High-Temperature Paint provides corrosion protection.

Single-part, aluminum-rich Corr-Paint(TM) CP4010 ceramic-silicone based coating protects steel components and structures for applications to 1200 deg F. It is resistant to acids, bases, and solvents, and provides thermal-shock, salt-spray, and UV resistance. Water-dispersible coating dries at room temperature and cures fully during operation at temperatures above 450 deg F. Non-flammable, low VOC...

Read More »
Interfaces offer high retention contacts.
Construction Equipment and Supplies

Interfaces offer high retention contacts.

Micro-Rugged Interfaces have shrouded and keyed insulators, and PCB terminations including press fit, solder locks, and mechanical hold-down options. Board-to-board interfaces are available on .050 in., 2 mm, and .100 in. pitch. Micro Card interfaces for .031 and .062 in. boards have terminations on .8 mm and 1 mm pitch. Standard and high speed IDC cable systems are available on .050 in., 2 mm,...

Read More »
DC/DC Converters employ 300 kHz frequency, buck topology.
Electrical Equipment & Systems

DC/DC Converters employ 300 kHz frequency, buck topology.

LSN D3 Series SIPs are non-isolated DC/DC converters that accept 3.3 V inputs (3.0 to 3.6 V input range) and deliver 1, 1.2, 1.5, 1.8, 2, or 2.5 V outputs rated at 10 A. They employ single-in-line (SIP) packages that measure 2 x 0.55 x 0.34 in., and may be configured in vertical or horizontal orientations. Converters facilitate true point-of-use (point-of-load) power processing. Their on-board...

Read More »
Load Cell System can be scaled to 5 digits.
Electrical Equipment & Systems

Load Cell System can be scaled to 5 digits.

System combination is comprised of HSW (Hermetically Sealed Load Cell) and DPM-3 Panel Mount Meter. Suitable for various industrial and OEM force measurement and weighing applications, DPM-3 samples 60 readings per second, has analog output, and provides true peak reading capability. HSW tension or compression Load Cell is offered in various ranges from 1,000 to 50,000 lbs.

Read More »
Pressure Washers clean with hot water.
Cleaning Products & Equipment

Pressure Washers clean with hot water.

HG Series natural gas, stationary hot water pressure washer for wash bays is available in 15 models which have CSA certification to UL1776 specs. Washers have 208, 230, or 460 V, single or three phase motors rated 6.0 or 8.0 hp, with electronic ignition and standing pilot light. Washers also have 24 V control system, vacuum switch, thermal relief valve, overpressure safety controls,...

Read More »
Fiber Optic Light Source produces high intensity spots.

Fiber Optic Light Source produces high intensity spots.

Ellipsoidal aluminum reflector lamps can be used as light sources in fiber optic applications. They produce small, uniform, high intensity spot, come in 9.5 to 50 mm dia sizes, and provide light intensity from 0.5 to 150 W. For high output applications, dichroic reflectors are available, which let wavelengths longer than 700 nm pass through to reduce heat. Light sources can be supplied with lamps...

Read More »
Tube End Facing Tools suit pressure vessel fabrication.

Tube End Facing Tools suit pressure vessel fabrication.

Two types of tools are available: Fixed-Type for 1/4 to 9/16 in. OD tubes, and Insert-Type for 5/8 to 2 in. OD tubes. Tools face brass, copper, steel, stainless steel, copper nickel, and titanium tubes. Cutter on fixed-type tool can be sharpened, and insert-type tool uses easy-to-replace cutter bits. Fabricators use tube facing tools to trim and face tubes before they are rolled, and re-tubers...

Read More »
Heat Flow Meters are easy to calibrate.
Sensors, Monitors & Transducers

Heat Flow Meters are easy to calibrate.

HFM Heat Flow Meters determine various factors like thermal passivity, thermal resistance, and thermal exchange that cannot be recorded by temperature alone. Measurements make it possible to evaluate and manage thermal insulation, energy control, and in/out balance of heat flow. Applications include medical research, solar and geothermal energy, industrial furnaces, and manufacturing plants.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers