Aprima Medical Software, Inc

Electronic Components & Devices

VCO has phase noise of -114 dBc/Hz at 10 kHz offset.

Model CRO2690A-LF operates at 2,690 MHz with tuning voltage range of 0.5-4.5 Vdc and features typical tuning sensitivity of 7 MHz/V. Operating over temperature range of -40 to +85Â-ºC, unit delivers output power of 4 dBm at 5 Vdc supply while drawing 22 mA. Second harmonic suppression is -15 dBc for RoHS-compliant product. Measuring 0.5 x 0.5 x 0.22 in., it is suited for satellite...

Read More »
Ultrasonic AC-Powered Flowmeter has integral/remote display.
Test & Measurement

Ultrasonic AC-Powered Flowmeter has integral/remote display.

Offered in single- and dual-beam configurations with rate and total display, Transi-Flo I uses transit time technology to measure difference in waves traveling in and against fluid flow direction. Available sizes range from 1 Â-¼-12 in., and system accuracy is ±1% for single-beam or ±.5% dual-beam. Flowmeter is optimally suited for applications involving conductive,...

Read More »
Ultrasonic Flow Meter features battery-powered design.
Test & Measurement

Ultrasonic Flow Meter features battery-powered design.

Compatible with conductive, non-conductive, and aggressive liquids, Transi-Flo II uses transit time technology to measure difference in waves traveling in and against fluid flow direction. Unit comes in single beam model with or without rate display, which can be integrally mounted on flow meter or remotely. Designed for line sizes from 1Â-¼ to 12 in., meter provides ±1% accuracy and...

Read More »
Robotic Beam Cutting and Scribing System automatically generates tool paths.
Agricultural & Farming Products

Robotic Beam Cutting and Scribing System automatically generates tool paths.

Robotic Beam Cutting and Scribing System automatically generates tool paths from CIS/2 part files for cuts, copes, holes, slots, notches, cutouts, and assembly markings on beams up to 40 ft long, 4-44 in. wide, and 4-18 in. high. Featuring servo-robot laser vision and FANUC ARC Mate® 6-axis robot arm, system is controlled by StruCIM® software that allows operators to load CIS/2 part...

Read More »
Machinery & Machining Tools

Programmable EDM Machines allow long hours of unattended burning.

Model EDAF2 provides worktable dimensions of 21.7 x 13.8 in. with payload of 1,102 lb, while EDAF3 has table dimensions of 27.8 x 19.7 in. with max payload of 1,764 lb. Both EDMs are equipped with spark gap monitoring and arc prevention technology that helps prevent destructive DC arcs, allowing manufacturers to burn any application fully unattended. High Quality Surface Finish technology...

Read More »
Permanent Magnet DC Gearmotors and Motors feature brush-life sensor.
Electrical Equipment & Systems

Permanent Magnet DC Gearmotors and Motors feature brush-life sensor.

Type 42A permanent magnet DC gearmotors and motors include electronic brush-wear sensors, integrated into motor housing, that indicate when either of brushes is nearing end of its useful life. Sensor system allows OEMs to electronically monitor brush wear to maintain uninterrupted operation of PMDC gearmotors or motors. When equipped with sensors, gearmotors and motors can accommodate built-in...

Read More »
Calibration Instrument fosters EPA Method 334.0 compliance.
Laboratory and Research Supplies and Equipment

Calibration Instrument fosters EPA Method 334.0 compliance.

Used for calibrating on-line chlorine analyzers in compliance with US EPA Method 334.0, P334 Colorimeter comes with step-by-step procedure guide, NIST traceable standards, and certificate of calibration from factory. Included primary chlorine standards kit consists of constant concentration liquid standards contained in double-ended ampules and one bottle of pre-measured double distilled water....

Read More »
Watertight Expansion Joint withstand chlorinated water.
Laboratory and Research Supplies and Equipment

Watertight Expansion Joint withstand chlorinated water.

Suited for use in submersed locations, SUBMERSEAL precompressed expansion joint seal is manufactured to resist degradation while continuously immersed in chlorinated, saline, or potable water environments. Single convex silicone-bellows sealing surface is backed by integral, pressure-resistant, impregnated foam backing. Available in widths from Â-½-4 in., product provides movement...

Read More »
Liquid Flow Logger targets wellhead applications.
Test & Measurement

Liquid Flow Logger targets wellhead applications.

Designed to measure produced water and hydrocarbon condensate, TriFlo System offers complete interchangeability of components between 1, 1 Â-½, and 2 in. flow meters, all of which can be accessed without breaking pipe connections. System delivers accuracy of ±1% or better and is capable of 16-point linearization. LCD display provides 40-day flow log and indicates rate and total...

Read More »
Magnetic Cylinder Position Sensors resist weld slag.
Sensors, Monitors & Transducers

Magnetic Cylinder Position Sensors resist weld slag.

Equipped with WeldGuard(TM) protection, Q-pak®, BIM-UNR, and BIM-UNT Sensors are impervious to weld slag and splatter often accompanying MIG and TIG welding operations. BIM-UNR model mounts within C-groove cylinders, while BIM-UNT sensor mounts in T-groove dovetail or tie rod pneumatic cylinders, all without additional tools or accessories. Featuring IP68 protection rating, Q-pak...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers