MOST Cooperation
Karlsruhe DEU
Share:
Toolholder holds inserts with cutting depths to .500 in.
GROOVE 'N TURNÃ-® internal toolholder can be used on conventional, Swiss, and CNC machines to hold threading inserts and grooving inserts in sizes from .004-.155 in. It is available in Ã-¾ and 1 in. dia, has 1 in. min bore, and holds inserts with cutting depths to .500 in.
Read More »
Turbine Agitator uses hydrofoil/gas dispersion impellers.
Suited for agitator service in applications to 600,000 gal, GT Turbine Agitator features double reduction gear drive and cast iron housing. Suited for indoor or outdoor operating environments, 1Ã-½-3Ã-½ in. dia GT shafting is oversized and tested to resist maximum torsional loads and bending moments. Product is equipped with NEMA or IEC C-flange motors from 1-30 hp, AGMA-certified helical...
Read More »
HEPA and ULPA Filters meet stringent air purity requirements.
Microguard 99 Filters eliminate particles down to 0.3 microns with efficiencies of 99.97, 99.99, and 99.999%. Microglass fiber media is waterproof and heat-resistant to 1,000Ã-
Read More »
Audio Power Amplifier targets multi-channel applications.
Single-chip Model STA5150 delivers 200 W into 4 ohm load with less than 10% distortion. It combines Indigo's BASH topology and Bipolar-CMOS-DMOS process technology. BASH technology uses DMOS power transistors operated in class AB mode, reducing EMI and distortion typical of class D switching amplifiers. By continually adjusting power supply voltage, depending on amplitude of amplified audio...
Read More »Remote Monitoring Package is based on STARDOM.
Based on network-based control system, eCUBE remote equipment monitoring and control application package enables users to build network-based remote monitoring and control system. Package provides choice of controller interfaces, fault-tolerant controller units, and ability to configure application from components in proprietary application portfolio. Also offered, eCUBE aqua remote monitoring...
Read More »Airflow Unit provides HVAC fabric duct balancing.
Adjustable Flow Device(TM) is a polyester mesh cone with factory-set or field-adjustable hemmed drawstring aperture for balancing airflow and static pressure in fabric air dispersion models. It stages inflation and reduces in-duct turbulence at outlets or fittings. Available in 6-72 in. diameters, unit has large scrim openings that do not attract HVAC system particles. Device can be replaced for...
Read More »
Blade Style Tooling accommodates cutting depths to 32 mm.
DEEPGROOVEÃ-® Blades are in face grooving, 20mm major diameter and greater, or OD/parting configurations and are compatible with 2, 3, 4, 5, and 6 mm inserts.
Read More »
Profiles provide thread cutting.
MICROBITÃ-® acme threading profiles cut threads sizes 6, 10, 12, 14, and 16 tpi in diameters from 3/16 to Ã-½ in. Tools have geometry to cut specific thread profile or lathe can be set to cut alternate thread sizes.
Read More »
Boring Bars provide deep cutting.
MINI-BOREÃ-® indexable boring bars include carbide trigon bars, which offer rigidity and long extension ratios. They are available in 3/16, Ã-¼, and 3/8 in. diameters for WCGT style .156, .187, and .250 in. IC inserts.
Read More »
Video Frame Grabber suits video surveillance applications.
Model FG104(TM) captures analog broadcast signals across PCI bus in embedded computer system. Based around Conexant Fusion(TM) 878A video decoder, PC/104-Plus form factor board supports NTSC, PAL, and SECAM video formats for capture resolutions up to 768 x 576 pixels and 30 frames/sec. Supporting 4 CVBS composite inputs or 3 composite video and 1 S-Video input source, module is capable of...
Read More »