Comptel Corporation
Helsinki FI-00100 FIN
Share:
Fluorescent Lighting provides undersurface illumination.
SlimLink flicker-free fluorescent lighting system features Ã-¾ in. high x 1 Ã-¾ in. deep profile, allowing fixtures to be concealed under curved or flat surfaces. Housing lengths range from 10-23 in. Lights can be used alone, end-linked, or cord-linked to form continuous rows of up to 10 units per run. T4 linear fluorescent lamps provide illumination from 6-20 W per SlimLink unit....
Read More »
SMA Connectors are offered in panel-mount versions.
Suited for use in high-frequency and microwave applications where small size is required, SMA, 2-hole, panel-mount connectors are fabricated to MIL-STD-348A, Section 310 with nickel or gold plated brass bodies, Teflon insulation, and gold plated contacts. Model RSA-3261 SMA jack and RSA-3221 SMA plug have solder cups, while RSA-3262, RSA-3268, and RSSA-3269 have solder posts with flush and...
Read More »Wireless OEM Module provides 900 MHz performance.
Model 9XCite(TM) FCC-approved, embedded wireless module has power output of 1 mW and -108 dBm receive sensitivity providing extended transmission range. It communicates 300 ft indoors/urban environments and 1,000 ft line-of-sight with dipole antennas. Module accepts 2.85-5.50 Vdc and is optimized for low power applications. Data throughput is user selectable at 9,600 bps or 38,400 bps and...
Read More »
Servo Controller accepts current or voltage input.
Model EM70 microprocessor-based controller offers high visibility of Control Motor opening display, which is shown in 7-segment bar graph. Zero/Span adjustment of opening can be done automatically at touch of single button. Combining SSR and relay, drive unit can control large capacities from 20-240 V/2 A. Dust and splash-proof front panel is equivalent to IP66. Events/Alarms, analog output,...
Read More »
SBC is based on Intel-® XScale(TM) RISC processor.
VIPER PC/104 form factor embedded processor board uses 400 MHz PXA255 XScale application processor, which is fully compliant with ARM v.5TE instruction set. At 3.6 x 3.8 in., with typical power consumption of 1.4 W from one 5 V input and less than 200 mW in standby mode, product includes flat panel display controller, 10/100baseTx Ethernet, 5 serial ports, I/O expansion using PC/104 bus,...
Read More »Staplers accept multiple leg lengths.
Requiring changeover of anvil hooks to switch carton closing top staplers from one leg length to another, T tools accept multiple leg lengths, thereby reducing cost of switching. With reduced body contour that promotes maneuverability by user, design also incorporates ergonomically designed trigger cavity and trigger valve that eliminates wear.
Read More »
Choke Circuits offer dc resistance down to 0.20 ohm.
Packaged in lead-free, surface-mount, wire-wound designs, common-mode ICM-0805 and ICM-1206 suppress noise in USB 2.0, FireWireÃ-®/IEEE 1394, LVDS, and high-speed digital interfaces. With max dc resistance from 0.20-0.45 ohm, ICM-0805 is rated for currents from 450-280 mA and has common-mode impedance from 30-370 ohm @ 100 MHz. Max dc resistance for ICM-1206 models ranges from 0.3-1.2 ohm,...
Read More »
Controller minimizes transformer size in power supplies.
Pulse Width Modulator Model LT1950 employs control mechanism that protects, simplifies, and reduces size of isolated/non-isolated 15-500 W power supplies with 24 and 48 V input supply rails. Adaptive maximum-duty-cycle clamp circuit prevents transformer saturation and protects MOSFET from failures. Adjustable current-slope compensation allows optimization of transient response. Operating...
Read More »
Ball Valve increases safety in plastic piping systems.
Lateral reducing Series LMBV eliminates vulnerable area between ball valve and tee in piping connections. Adapter connects ball valve directly to piping tee and valve remains fully functional if accidental break occurs in line. Product is available in GeonÃ-® PVC, Natural Polypropylene, CorzanÃ-® CPVC, and KynarÃ-® PVDF. Lateral tee connections on adapter side range from Ã-¾-3 in....
Read More »
Oil Additive suits industrial and off-highway applications.
LuBoron(TM), with Boron CLS BondÃ-® friction-reducing technology, requires only one use to reduce varnish and gum build-up on synchros and gears and to inhibit wear. Treatment reduces backlash tooth drag in differentials, allowing more horsepower to wheels. It forms low-friction, hard surface, impervious to most contaminants, and is compatible with synthetic and mineral-based lubricants....
Read More »