VeriFone Holdings, Inc.
Paris 75010 FRA
Share:
IMM incorporates double turning-cube stack mold system.
Available in 40-450 metric ton sizes, K-TEC injection molding machines (IMMs) utilize FOBOHA's double turning-cube stack mold system, which has 3 parting lines that allow one IMM to mold 2 precision parts from 2 materials, label, and assemble finished product. By mounting secondary injection unit at 45Ã-
Read More »Pneumatic Lifts have ergonomic design.
Equipped with tilt or rotate units, pneumatic lifts feature 4.9 in. lowered load height and 30 x 44 in. minimum top size. Lifting capacity of 2,000 lb enables products to be used in place of hydraulic lifts.
Read More »
Flow Control Valves control air from cylinders.
Models JFC-4 and JFC-5 are combination needle and check valve flow controls used to control air flow from air cylinders. Units control speed at which piston strokes, either while extending or retracting, depending on location in circuit. They allow free flow from inlet to outlet past needle and check valve. In reverse flow, check valve is sealed and flow must pass through metered passage...
Read More »
Air Compressors offer out-of-the-box functionality.
Available in models from 5-15 hp, Ultra-Pack(TM) Compressors are factory-equipped with magnetic motor starter, air-cooled after-cooler, dual control, automatic tank drain, low oil level shutdown, and tank isolator pads. To facilitate installation, compressors come as complete air systems, plumbed, pre-wired, and ready to run.
Read More »
Surface Profiling Systems accommodate up to 4 gauging heads.
Talysurf CLI Systems provide 3D surface profiling, as well as mechanical and analytical capabilities for 2D measurements. Models CLI 2000, 1000, and 500 offer measuring envelopes of 200, 100, and 50 mm, respectively. Chromatic Length Aberration Gauge, Laser Triangulation Gauge, and Inductive Gauge units are available to meet user requirements. Talysurf CLI Systems are suited for processes that...
Read More »
Cleaning System handles all types of ductwork.
Model DCM-600 spins cleaning brush inside ductwork and breaks deposits loose from walls. Compressed air comes out of brush head to push debris to vacuum source, while negative air HEPA vacuum captures dirt and debris. Unit includes Ã-½ hp motor with forward/reverse controls for cross-scrubbing, and variable speed control that allows slow speed for flex/insulated ducts and high speed for steel...
Read More »
Magnification Light is ESD safe.
Model ESD Omnivue features conductive coatings and static dissipative materials and coatings, which eliminate static discharge. Three 9 W, 5,000 K compact fluorescent lamps provide 27 W of light from top and both sides of magnifier, or 18 W of side-to-side lighting. Three-diopter, fully rotational magnifier lens provides precise positioning to eliminate glare. Spring-loaded base and arm allow...
Read More »
Hybrid Bearings offer alternative to all-steel bearings.
Featuring wear resistance, Hybrid Bearings combine silicon nitride rolling elements with steel rings. Inherent insulating properties prevent electrical arcing, which can cause fluting pattern surface damage to raceways. Standard types include hybrid single row, deep groove ball bearings with bore diameters from 5-110 mm; sealed and greased-for-life ball bearings protected by steel-reinforced,...
Read More »
Pressure Regulator targets space critical applications.
Diaphragm pressure regulator Model PRD controls output pressures from 0-40 psig, with maximum rated inlet supply pressure of 300 psig. Both inlet and outlet ports are tapped 10-32 UNF. Suited for gas and pnemuatic applications, non-relieving, single-stage regulator is offered in brass, anodized aluminum, 303 stainless steel for corrosion resistance, and 316 stainless steel for high purity...
Read More »Coiled Tubing permits unrestricted flow in confined spaces.
Coiled Fluoroplastic Tubing is chemical-resistant, non-flammable, and has low coefficient of friction. Featuring multiple, retractable coils in single tube, it can be manufactured from Texfluor(TM) PTFE, FEP, PFA, and MFA in various lengths and ID sizes from 1/16-2 in. Non-wetting and non-leaching, tubing is available in resins with very low refractive index for applications where operator needs...
Read More »