Actions Semiconductor Co., Ltd.
Guangdong 519085 CHN
Share:
Compact Toolholder is suited for high-speed applications.
Offering run-out accuracy of less than 3 microns and feed rate up to 20 m/min, TRIBOS-RM is designed for cutting speeds up to 50,000 rpm in applications that require low interference. Clamping process, which uses elastic forces of material to clamp tool shank, can be done within 30 sec via SVP-2 (manual) or SVP-3 (automatic) clamping device together with corresponding reduction inserts. Due to...
Read More »
Linear Ball Bearings come in US and European specs.
Conforming to AISI 52100 standards and hardened to HRc 60-64, steel Linear Ball Bearings are available in adjustable, open or closed, and standard or heavy-duty types. Bore sizes range from .375-1.500 in. diameter. Number of ball circuits in each unit can range from 4-8, and unit lengths range from .875-3 in.
Read More »
Ceramic Bearings have lightweight, shock-resistant design.
Comprised of 28 ball-less bearings, BCCRIXM Series is made of Zirconia - ZrO2 ceramic material, which resists deformation, supports high-temperature operation, and exhibits chemical resistance. Zirconia is also nonmagnetic and acts as electrical insulator. Shock absorption and antifriction characteristics make bearings suitable for use in powder, dust, and muddy water environments at speeds under...
Read More »
Spherical Bearings suit low frequency applications.
Available in inch and metric sizes for precision and commercial tolerance applications, Spherical Bearings have spherically shaped inner ring and cylindrical bore for shaft mounting. Units consist of 2- and 4-piece types including self-lubricating models. With outer diameters from .4687-4.000 in. and from 5-25 mm, bearings fit shafts ranging from .165-1.875 in. and from 5-25 mm in diameter.
Read More »
Rod End Bearings come in 125+ inch and metric sizes.
Suited for precision and commercial tolerance applications, bearings come in male and female configurations with optional lubricator fittings. They have spherically shaped inner ring and cylindrical bore for shaft mounting, while outer surface of outer ring facilitates installation into any housing. Able to accommodate moderate shaft misalignments, bearing construction consists of 2- and 4-piece...
Read More »
Modular Plastic Conveyor Belt features pinless design.
With 1.5 in. pitch, Flex ONE side-flexing, plastic modular belt offers tight turning radii as low as 1.42 x belt width. Snap Link(TM) modules snap together for maintenance, and openings are minimized for maximum safety. Because there are no pin holes, all surfaces on belt are exposed for cleaning.
Read More »
Feed-Through Unit prevents twisted or broken cables.
Used with SRU rotary actuator, Electric Feed-Through Unit enables digital signals to be conveyed to sensors and power to be supplied to digitally operated actuators. Using jumper, EDF-SRU can be reconfigured to Bus operation by routing power supply and Bus signal via feed-through. Input and output ends are equipped with housing connectors or sockets. For output end, users can choose between M12,...
Read More »
Gripper suits internal and external assembly applications.
Designed to fit O-rings not only to shafts, but also in holes, 6-finger Model ORG 85 features integral stroke and triple jaw sets that move independently from one another. O-ring is first released from first 3 fingers, and then released from last 3 fingers in controlled manner. Clamping width of diameter to be fitted ranges from 5-150 mm. Stroke of 2 sets of triple jaws range from 0-21 mm for...
Read More »
Clamping System utilizes electro-permanent magnets.
With MAGNOS Clamping System, 5-sided machining is possible at high holding forces, without any interfering contours of clamping device. Pole extensions that act as workpiece support allow user to position different workpieces rapidly and precisely. Uniform clamping force is possible due to poles' quadratic geometry. Pole sizes of 50, 75, and 100 mm are available, enabling holding forces to be...
Read More »