Lamerholm Fleming Ltd    Stevenage Hertfords SG1 2DE  United Kingdom
May 21, 2008 To provide complete picture of physical environment that product has endured through transit or in storage, RD404 Tilt and Roll Accelerometer adds monitoring abilities to ShockLog event data recorders. Connecting directly into RD298 ShockLog via RS232 cable, it draws less than 1 mA during operation and stores data within RD2998 memory. Data is recorded in quadrants and displayed in range of ±90°. Unit can be used with RD299 HPT sensor for environmental profile of product under surveillance.

austriamicrosystems AG    Schloss Premstaetten A 8141  Austria
May 20, 2008 Qualified to AEC-Q100, AS5134 Rotary Encoder IC supports commutation of brushless DC motors in ambient temperatures up to 150°C. With 8.5-bit resolution, unit can recognize 360 positions within one 360° turn and is accessible with serial or PWM interface. Device features 3 programmable incremental outputs and 1-6 pole pairs. Housed in SSOP-20 package, IC offers power saving mode with power consumption of less than 1.5 mA and start-up time of less than 250 µs.

eps corp    Costa Mesa, CA 92626
May 20, 2008 xChange Point(TM) is hardware/software carbon and energy monitoring solution, that allows companies to track energy usage and CO₂ emissions at product, plant, and corporate level. It is designed to integrate system-wide information in real-time and is able to work with demand response and other smart grid signals. Decision-makers can gain insight into trends and cost-concerns, such as when to replace equipment.

DPS Telecom    Fresno, CA 93727
May 20, 2008 After taking TBOS alarm data from equipment, NetMediator T2S G5 converts data to detailed SNMPv3 traps. System can then send alarms to master or send instant pager and email notifications directly to techs in field. Compatible with all standard TBOS gear using RS-485 polling ports, LAN-based SNMP/DCPx RTU monitors up to 4,096 TBOS alarms, as well as 32 or 64 discrete alarm points. With SNMPv3 compatibility, unit can report to multiple SNMP masters or T/Mon NOC.

Dynapar    Gurnee, IL 60031
May 19, 2008 Suited for use on NEMA 23 and 34 brushless servo and step motors, HC20 features direct-read non-interpolated technology that stems from custom-phased array ASIC, and is available with 5-26 Vdc operating range. Temperature rating of 120°C will not limit motor performance, allowing manufacturers to keep from de-rating torque specs. Capable of up to 2,500 ppr, encoder is available with commutation tracks for 4, 6, or 8 pole variants of brushless motors.

Honeywell Analytics    Lincolnshire, IL 60069
May 19, 2008 Used for detecting trapped gases in hazardous applications, Impact Pro assists Safety Engineers at sites and confined-space rescue incidents where carbon monoxide, low oxygen levels, and other gases may be present. Sensors are built directly into cartridge, and up to 4 gases - carbon monoxide, oxygen, hydrogen sulfide, flammable - may be detected simultaneously. IP67-rated unit offers one-touch operation and multilingual display as well as Safelink communications option.

Omega Engineering, Inc.    Stamford, CT 06907
May 19, 2008 With amplifier/regulator accuracy of 0.25%, 6SE01079 Series of Marine Pressure Transducers conform to Mil-I-45208A quality requirements. Stainless steel constructed products have vibration limit of 0.04% RO/G, isolated 0-5 Vdc output, and are 28 Vdc powered. They are available in gage or absolute pressure, ranges of 50 in. H20 to 5,000 psi, and come with internal shunt resistor to simulate transducer output.

Vaisala, Inc.    Woburn, MA 01801 1008
May 19, 2008 Based on DRYCAP® polymer sensor technology, Model DMT152 Dewpoint Transmitter measures dry air or gas in OEM applications. It can measure dewpoint even down to -112°F or 1 ppm of humidity. Exhibiting long-term stability against condensation, DMT152 mechanics are designed for harsh environments requiring protection against dust, dirt, and splashed water. Applications include air and plastics dryers, dry chambers, pure gases, and high-voltage circuit breakers.

Baumer Ltd.    Southington, CT 06489 1534
May 16, 2008 EcoSpin Magnetic Encoder is modular, non-contact sensor system that delivers reliable performance in dirty, contaminated, and high vibration operating environments. With depth of 10 mm, IP67-rated encoder contains no moving parts and includes spacer strip mounted between magnetic ring and sensor, simplifying installation and adjustment. Device can measure rotational speed of spindles, shafts, rollers, and webs as well as measure angle of cuts made with high-vibration machinery.

Solartron ISA    Durham DL4 1LH  United Kingdom
May 15, 2008 Suited for subsea oil and gas applications, SST1500 deepwater differential pressure transmitters operate to depths of 5,000 ft. Units utilize silicon crystal sensor that provides accurate measurement and 60-month stability specification. Ultra deepwater SST3000 Series of pressure and temperature transmitters operate to depths of 16,400 ft with working pressures of 10,000 psi. All feature fully welded, duplex stainless steel construction and dual compartment design with glass-to-metal seal.

AMETEK Petrolab Company    Broken Arrow, OK 74012
May 15, 2008 With PetroOXY Tester, fuel producers and terminal facilities can monitor and control fuel's oxidation stability. Unit features hermetically sealed test chamber in which 5 ml sample is combined with oxygen at pressure of 700 kPa and heated to temperature of 140°C. Test conditions initiate fast artificial aging process, which is measured by pressure drop within chamber. Time needed to achieve fixed pressure drop is directly related to oxidation stability of fuel.

Berkeley Nucleonics Corp.    San Rafael, CA 94901
May 15, 2008 Since QCC allows subtraction of background in real-time (1 second down to 100 ms), SAM 940 systems are appropriately specified for short acquisitions down to 1 second or less. For RIIDs, 2 x 2 in. NaI detector lets user ID presence of Cs137 at less than 1 µrem/hr/sec. Also available, 3 x 3 in. NaI detector is capable of identifying Cs137 at 500 nrem/hr/sec. Stabilization is performed with K40, which will not interfere with detection or cause anomalies that produce false positives.

Advantech Automation Corp.    Cincinnati, OH 45240
May 14, 2008 Designed for use with ADAM-5550 series PACs, ADAM-5081 features 2,500 Vdc isolation, high-speed frequency mode (5 Hz to 1 MHz), and counter code at 1 MHz. Digital filter eliminates noise and interference (1-65,000 µsec), ensuring accurate data collection and transmission, and 4 counter modes are available. Along with 4 digital output channels, solution offers frequency mode that supports up to 8 channels and can control range of electromagnetic wave status under certain conditions.

Kistler Instrument Corp.    Amherst, NY 14228 2119
May 14, 2008 Featuring digital charge amplifier in compact sensor housing, Type 9238 enables adjustment to processing operations. Sensor sensitivities can be programmed by ManuWare(TM) software, which matches sensor to signal conditioners or process monitors. Since transmitter measures force indirectly through proportional material strain, it can be located in accessible locations within manufacturing machinery. Single, IP67-rated cable offers resistance to production environments.

Colibrys, Inc.    Stafford, TX 77477
May 14, 2008 Offering constant frequency response up to 2 kHz with less than 5% variation, VS9000 Capacitive Accelerometers cover full range from ±2 to ±2,000 g. Combination of extended bandwidth and high degree of miniaturization make series suited to meet requirements of vibration measurement systems. Applications include Health and Usage Monitoring Systems, aeronautics, railway technologies, and automotive crash testing.

MAG IAS, LLC    Erlanger, KY 41018
May 13, 2008 Offering simultaneous 5-axis contouring, HyperMach H4000 provides contained cutting of parts up to 2 x 4 m. Machine offers choice of 30,000 rpm 60 kW/80 hp HSK63A spindle or 20,000 rpm 85kW/115 hp HSK100A spindle. Water-cooled motors power table/pallet receiver at speeds up to 2,000 ipm. High-speed ball screws drive Y and Z axes, while spindle carrier rotates at 150°/sec in A and C axes. Model H4000 comes standard with 96 tool automatic tool changer, field-expandable to 190 tool capacity.

GAO Tek Inc.    Toronto M1B2K4  Canada
May 13, 2008 Suitable for SM/MM types of fiber, Model GAO811 handheld visible red laser source can distinguish faults of fiber jumper, jumper board, distribution, frame, and tie-in. It also helps overcome limitation of near blind area of OTDR. Laser cannot only be reflected out from macro bend point, overlay layer, or naked fiber position, but can also be jetted from tie-in which is not linked well. Unit offers greater than 1 mW output power, low voltage warning, and automatic power off.

Tractel, Inc., Griphoist Div.    Canton, MA 02021
May 13, 2008 Dynafor LLX2 load indicators feature cross-plane design where upper and lower attachment points are positioned 90° from each other allowing articulation in 2 planes. Available display options include lb, short ton, metric ton, Kg, Kn, and daN, with accuracy of .1%. Other features include 2.4 GHz ZIGBEE connection between sensor and display with 260 ft range, ability to monitor up to 8 sensors, and weather protection to NEMA 4X (IP66) for sensor, IP54 for display.

Xspect Solutions Inc.    Wixom, MI 48393
May 12, 2008 The Phoenix is suited for inspecting round and square holes, slots, and spherical features on car bodies and computer chassis, as well as flush-and-gap tolerances on car and truck body parts. Hybrid system combines high-resolution image processing benefits of CCD camera in X-Y plane with multiple laser triangulations for measuring Z plane. Triangulation is produced in 2 orthogonal directions. Sensor is 120 x 12 x 90 mm, with working distance from measured feature up to 100 mm.

C&K Components    Newton, MA 02458
May 12, 2008 MDS Series micro snap-acting detect switches are available in vertical and right-angle PCB mount, with 2.9 mm travel, and SDS Series side-actuated detect switches have 2 mm profile and 2 mm overtravel. Featuring top or side actuation, SDT Series micro mini pendulum detect switches offer 2.2 mm profile, while HDT micro mini detect switches have 3.35 mm profile. Surface mount switches are implemented on server blade as safety mechanism to guarantee blade is powered down.