Tingue Brown & Co.    Saddle Brook, NJ 07663
Apr 29, 2013 Featuring high-density weave for wear resistance, Black Knight Belting is designed for installation on flatwork ironers, folders, and other laundry equipment where non-stop productivity is required. USA-made belts are available in 1, 1 ½, 2, 2 ½, 2 ¾, and 3 in. widths and in 375 ft rolls with choice of lacing styles. Glued ends or sewn endless options are available.

Gates Corporation    Denver, CO 80202
Feb 25, 2013 Engineered for drop-in performance, G-Force™ C12 Continuously Variable Transmission Belt is designed for ATVs, UTVs, and snowmobiles. Cords are bonded to specially formulated adhesion gum with aramid fiber loaded rubber, which results in side-load resistance, preventing belt distortion and edge cord pullout. Belt also uses neoprene, which features trapezoidal top-notch and rounded bottom cog design to maximize heat control and flexibility.

TB Wood's, Inc.    Chambersburg, PA 17201
Jun 20, 2011 Suited for problem drives that require impact strength, Premium Banded V-Belts feature multiple layer tie band that provides lateral rigidity to prevent belts from turning over or coming off drive. Clutching non-rubber surfaced cover allows momentary slippage due to excessive overloads without burning belts up, while Kevlar or Aramid tensile cords yield maximum strength and virtually zero stretch. Curve design compensates for sidewall bulge, which occurs when belts bend around sheave.

Ondrives Ltd.    Chesterfield, Derbyshire S41 9RN  United Kingdom
Nov 18, 2010 HTD pulleys and belts include timing pulleys, starting at 5 mm pitch to suit 9, 15, and 25 mm wide belts, available with pilot or taper bore. Different versions are available depending on number of teeth required. Standard pitches also include 8 and 14 mm, which suit belts to 85 mm. Depending on size, pulleys are steel with zinc-plated steel flanges or cast iron, and belts are glass fiber reinforced, rubber back/teeth with nylon fabric tooth facing to DIN/ISO 5296.

Ondrives Ltd.    Chesterfield, Derbyshire S41 9RN  United Kingdom
Oct 20, 2010 Available with pitch from 2.5-10 mm, T Type Pulleys are made of aluminum with zinc-plated steel flanges and are either center-drilled or pilot-bored. Synchronous timing belts that accompany pulleys range in width from 6-32 mm and are double sided with Aramid tension members. Special polyurethanes, anti-static, machined, ground, and punched belt options are available.

Gates Corporation    Denver, CO 80202
Jul 26, 2010 Molded notch V-belt products are constructed with EPDM (Ethylene Propylene Diene Monomer), whch exhibits resistance to ozone, heat, and weather. Bandless, molded notch construction conserves energy while promoting efficiency, and belts also tolerate misalignment for smoother running performance. Operating from -60 to +230°F, products are resistant to hardening and also meet RMA standards for oil and heat resistance as well as static conductivity.

Belt Technologies, Inc.    Agawam, MA 01001
Apr 22, 2010 Suited for indexing conveyors that assemble plastic spray bottle caps and other multi-component assemblies, Stainless Steel Indexing Belts resist stretching and allow for exact positioning of tools and parts. Belts can be mounted vertically, allowing manufacturers to utilize both sides of conveyor, doubling number of simultaneously occurring operations. In addition to minimizing debris buildup, continuous-length belts eliminate frequent shutdowns associated with cleaning.

BLACKHAWK! Products Group    Norfolk, VA 23502
Jan 04, 2010 As duty gear line for law enforcement, pouches and belts produced from Nytek® nylon composite fabric are available in plain and basketweave finish. Stronger, lighter, and more flexible than leather duty gear, products can be polished in same manner as leather and cleaned to disinfect blood-born pathogens. Breathable construction will not absorb water; will not fade, crack, or dry out with exposure to UV rays, and maintains performance properties regardless of temperature.

Thayer Scale-Hyer Industries, Inc.    Pembroke, MA 02359
Nov 05, 2009 Built with stainless steel frame, Ultra-Sanitary Model SI features troughed belt to keep product away from edge, eliminating need for side skirts. Entire conveyor assembly is coupled to mass counter-balanced Force Measurement Suspension System that allows load cell selection based on net, rather than gross weighing requirements. Unaffected by dirt, shock, or vibration, system can withstand overloads in excess of 1,000% of rated capacity without damage or calibration drift.

Bowman Hollis Mfg., Inc.    Lagrange, GA 30241
Sep 17, 2009 With special grip tread contact surface, PHR160 RT is designed for pulling boxes positively through case sealer. Non-marking, tough nitrile rubber cover works in all sealer applications, including side- or bottom-belted sealers, while non-stretching carcass of 2 ply woven polyester is not affected by humidity or other environmental conditions. Available in any standard width, in either finished lengths with lacing, or in coils, belt can be joined by any type of mechanical lacing.

Bowman Hollis Mfg., Inc.    Lagrange, GA 30241
Jul 28, 2009 Designed for understacker/counter ejector applications on corrugated boxfolding equipment, style BH-E20CC, provides specific friction needed for transporting blanks, without wearing quickly. Belt can be fingerspliced endless, or joined with Clipper or Alligator lacing. Cover is non-marking against any type of paper or container board.

Belting Industries Co., Inc.    Kenilworth, NJ 07033
May 27, 2009 Made of Mylar/polyester, ultrasonically welded Film Belts feature perforated vacuum patterns and sprocket holes. Units offer chemical resistance, making them suited for areas where solvents, acids, and oils are present. Applications include disc memory drives, turntables, and miniature precision drives.

Belting Industries Co., Inc.    Kenilworth, NJ 07033
May 20, 2009 Hypalon-based HypaStretch (BIC 700) and urethane-based UraStretch (BIC 800) belts are versatile and customizable, enabling use in various applications. Hypsatretch, for example, is suited for paper transport and may be perforated for use on vacuum transports. Elasticity allows for use of belt sets without tensioners and compensates for machine variations. Belts suit small diameter pulleys, conveyors with fixed centers, as well as light-duty drive and transport applications.

Precision Alliance, The    Fort Mill, SC 29708
Apr 20, 2009 EXCEL-A-BELT miniature drive belt system incorporates arched tooth profile that provides rolling action between belt and drive sprocket, allowing for high-accuracy positioning and precise rotation transmission. Sprockets have bore sizes ranging from 3-25 mm and PD of 17-54 mm. Belt widths of 3, 4, 6, and 9 mm are available and system is suited for use with motors of 10-1,000 W.

Ammeraal Beltech Modular (Uni-Chains)    Reading, PA 19611
Feb 16, 2009 Developed for cooling conveyors in bakeries and other food applications, uni M-TTB CS, 0.5 in. pitch plastic modular belt features rounded bottom surface, making it suited for use with high-speed tight transfer conveyors. Belt features top curved surface and incorporates POM-D material with self-lubricating component that minimizes friction and optimizes nonstick characteristics. Cleaning is simplified by hygienic design of hinges.

Ammeraal Beltech Modular (Uni-Chains)    Reading, PA 19611
Feb 10, 2009 Designed around pin/rod technology that lends to belt strength, uni Flex ASB (1 in. pitch) and uni Flex L-ASB (2 in. pitch) are available with or without hold down tabs in combination with flat or curved surface. Beam strength is also optimized for spiral and other side flexing applications.

BRECOflex Co., L.L.C.    Eatontown, NJ 07724
Sep 16, 2008 Offered in belt widths of 6, 10, 16, 25, and 32 mm, AT3 endless timing belts have no weld zone, and feature minimum and maximum belt lengths of 720 and 1,701 mm, respectively. Tension member comes in steel/SS. Optional nylon facing on tooth side helps reduce coefficient of friction, while zero backlash pulleys are available for bidirectional belt drives. Belts are suited for small power drives requiring high tooth sheer strength as well as high speed applications.

BRECOflex Co., L.L.C.    Eatontown, NJ 07724
Sep 12, 2008 Available as open ended or welded endless belts, ATN timing belts come in regular AT10, AT10 tooth profile with ½ in. tooth pitch, and regular AT20 tooth pitches. Belt profiles can be assembled by hand utilizing accompanied mounting screws and inserts, while belt length and profile location can be chosen by increments of one tooth. Profiles can be made of any material to fit application (also material mix), and can also be assembled and disassembled without removing belt from machinery.

Power Drive Components, Inc.    Plainview, NY 11803
Jul 02, 2008 With Bello Superflex Ribbed Couplings, application engineers can select size where peak torque exceeds application torque X service factors. Units feature AL alloy 2011T3 and 303 stainless steel hubs and offer complete range of bores in clamp styles, suited for power transmission applications.

York Industries    Garden City Park, NY 11040
Apr 10, 2008 Constructed of high flex plastic over hardened fiberglass cord, TruMotion® Timing Belt is available in 2 mm GT, 3 mm GT, 3mm HTD, 5 mm HTD, .080 in., 1/5 in., and 3/8 in. pitches. Tooth surfaces have outer layer of nylon for wear resistance and quiet operation. Operating from -40 to 220°F, belt is corrosion- and abrasion-resistant, making it suitable for office automation, medical equipment, laboratory equipment, and DC stepper/servo devices.