Surface Treatment Equipment

Surface Treatment System generates blown-ion discharge.
Surface Treatment Equipment

Surface Treatment System generates blown-ion discharge.

Suited for conductive and non-conductive material, Dyne-A-Mite(TM) IT Elite etches, cleans, activates, sterilizes, and functionalizes surface. Concentrated blown-ion discharge causes micro-etching or scrubbing effect, removing organic and inorganic contaminants and facilitating application and adhesion of coatings, adhesives, inks, labels, and markings of all types. Quality control is...

Read More »
Plasma Surface Treater handles difficult-to-treat surfaces.
Surface Treatment Equipment

Plasma Surface Treater handles difficult-to-treat surfaces.

Eliminating need for priming, batching, and hazardous chemical surface preparation, Plasma3(TM) VCP utilizes variable chemistry atmospheric plasma to maximize effects of treatment for different materials. In-line solution, optimized to clean, etch, and functionalize range of materials, delivers aggressive and consistent treatment for conductive and non-conductive surfaces. Specifically, product...

Read More »
Lectro Takes Plastic Surface Treating to the Next Level
Surface Treatment Equipment

Lectro Takes Plastic Surface Treating to the Next Level

Lectro Engineering, the worldwide leader in three-dimensional plastic surface treating equipment has again raised the bar in the plastics industry. The LT 2012 Plastic Surface Treater increases the capacity of treated parts by 50% over the highly successful LT 2000 series. In doing so it has also reduced the footprint of a Bulk/Inline Lectro-Treat by 65%. This product opens up numerous...

Read More »
Surface Treatment Equipment

Plasma System is suited for high-volume PCB processing.

PROVIA(TM) system promotes uniformity of plasma treatment in HDI, flexible, and rigid circuit board processing applications such as desmear, etchback, and blind via cleaning. Gas distribution, vacuum, and electrical isolation technologies ensure uniform processing across each panel within individual processing cell as well as from cell to cell. Also supported, pre-etch conditioning technology...

Read More »
Surface Treatment Equipment

Plasma Treatment System processes flexible PCB materials.

Addressing need for processing of flex materials such as polyimide, LCP, and others, Model FP64 System is used for surface activation of coverlay material in flex panels to promote adhesion and prevent delamination. It is capable of running up to sixteen 18 x 24 in. panels per run for throughput performance of 64 panels/hr. All major components required for system operation such as vacuum pump...

Read More »
Surface Treatment Equipment

March Plasma Systems Dramatically Improves Throughput of Industry Leading PCB Plasma Treatment System

CONCORD, Calif., Feb. 28 /- March Plasma Systems announced today the release of improved PCB panel pre-etch conditioning technology. With this new technology the company's industry proven PCB series products can dramatically increase the throughput in applications such as desmear and etchback. Productivity improvements of more than 30% can be achieved with this new system enhancement. The new...

Read More »
CD Source Retrofit Package supports continuous operation.
Surface Treatment Equipment

CD Source Retrofit Package supports continuous operation.

Designed to support Intevac 200 lean disk manufacturing system, Diamonex CD Source(TM) Retrofit Package meets requirements of ultra-thin carbon overcoats for magnetic recording hard disks. Broad-beam, high-current density design minimizes surface damage from high-energy ion, while gridless ion source provides high ion flux. Substrate biasing is not required, as ion beam from CD ion source is...

Read More »
Surface Treatment Equipment

Surface Engineering Platform uniformly coats substrates.

Using liquid precursor which is atomized and sprayed into plasma jet, PlasmaStream(TM) coats surfaces to provide characteristics such as adhesion, waterproofing, low-friction slickness, or anti-microbial properties. Suitable for manufacturers of 3D, rigid, or molded parts, platform eliminates need for drying and curing; works at room temperature; requires no solvents, surfactants, or water; and...

Read More »
Atmospheric Pressure Plasma System has no moving parts.
Surface Treatment Equipment

Atmospheric Pressure Plasma System has no moving parts.

Atomflo(TM) generates stream of reactive gas for high-speed treatment of surfaces of all shapes and sizes prior to bonding, marking, painting, and coating. Designed to be hand-held or machine-mounted, aluminum plasma applicators deliver consistent and uniform treatment with linear beam sources from 1 in. to 1 ft. Plasma operates near room temperature at atmospheric pressure with reagent gas and...

Read More »
Shot Blasting System prepares concrete surfaces.
Surface Treatment Equipment

Shot Blasting System prepares concrete surfaces.

Used on concrete prior to application of paint or coatings, portable Model 1-9DEZ runs on 120 V and can strip, clean, and profile in one step, without rinsing or drying time. With 9 in. blast pattern and manual travel speed, blaster can prepare up to 275 sq ft/hr. Applications include residential garage floors, pool decks, concrete preparation prior to installation of wood flooring, small...

Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Sponsored

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.

Read More »

All Topics