
New MEMs 6DoF Inertial Sensor with Operating Temperature Range of -40 to +110 degree C
SCHA600 sensor offers centimeter-level accuracy in regard to vehicle dynamics and position to ensure safe, robust and verified autonomous driving. Available in SOIC housing body size of 18.7 mm x 8.5 mm x 4.5 mm (L × W × H) with 32 pins. Delivers good performance for automotive applications in regard to bias stability and noise.
Read More »
New Motion Sensor for Motion-based Gaming Controllers
ICM-42688-P is a 6-axis MEMS MotionTracking™ device that combines a 3-axis gyroscope and a 3-axis accelerometer in a 2.5mm x 3mm x 0.9mm package. Provides 40% low noise-figure and improves temperature stability by 2x, ensuring any motion event is measured with the highest accuracy, independent of temperature changes. Features InvenSense on-chip APEX motion processing engine for gesture...
Read More »
ACEINNA Ships $150 High Precision Navigation Solution for Autonomous Vehicles
New ACEINNA OPENRTK Module Rivals Performance of $10,000 Systems Highly Accurate, OPENRTK Module is extremely reliable, smaller, easier to integrate, and far less expensive The new ACEINNA OPENRTK330L is the only solution on the market to integrate a triple-band RTK/GNSS receiver and a triple-redundant inertial sensor enhancing the safety of Autonomous Systems. Andover, MA, April 1, 2020...
Read More »
New 3DTX10 and 3DTX08 Emitter Antennas are RoHS and REACH-Compliant
Provide very high precision motion capture in the range of 20-50cm, depending on the Rx-sensor (6x6mm to 11x11 or 15x15mm) in use. Allows the real-time precise tracking of the position and orientation of objects in space. Ideal for VR/AR and motion capture applications.
Read More »
Polymer Protection For Optical Fiber
To learn more about the challenges your optical fibers face, and which polymers are best to protect them, download this white paper.
Read More »
New Non-Contact and Solid-State Sensor is Used for Measuring Riding Speed
Features 4.5 – 20 VDC supply voltage and -20°C – 100°C operating temperature. Offers 7+1.4/-1.1 mA and 14+2.8/-2.2 mA signal output low and high respectively. Ideal for E-bikes, E-scooters, ABS systems applications.
Read More »
New OpenRTK330L Triple-Band RTK/GNSS Receiver Offers Ethernet Interface
Equipped with built-in triple redundant inertial sensor arrays to provide cm-level accuracy, enhanced reliability, and superior performance during GNSS outages. Integrates 2 Degree/Hour IMU to offer ten to thirty seconds of high accuracy localization during full GNSS denial. Operating temperature ranging from -40C to +85C and has RF and baseband support for the L1, L2, and L5 GPS bands.
Read More »
New OpenIMU330 Inertial Measurement Unit Powered by ARM M4 CPU with Floating Point Unit
Measures 11mm x 15mm x 3mm and designed for use in automotive ADAS and autonomous systems for electronic stability control and lane keep assist functions. Comes with triple-redundant architecture to meet performance, reliability and cost requirements of autonomous vehicles and self-driving taxis/delivery vehicles. Features include 3 axis MEMS angular rate sensor and accelerometer, open source...
Read More »
New Inertial Sensor Provides Resolution and Low Noise Density for Recording Vibrations
Evaluation kits are available for evaluation and configuration of sensors to support projects and developers. Inertial sensors from first sensor achieves resolution of 10 µg or 0.0005° (2 arc seconds). Ensure safety in events such as storms, earthquakes, large loads or changes in the foundations.
Read More »
TDK Corporation Launches Motion, Sound and Ultrasonic Sensor Solutions, Embedded Motor Control and Magnetic Sensors, Power Supply Solutions as well as Passive Components At Embedded World 2019
HVC 4420F embedded motor control and magnetic sensors by TDK-Micronas enables direct drive of small brush-type, stepper or brushless electric motors in smart actuators. Meets increased functional and diagnostic demands with flash memory extended to 64 KB and SRAM to 4 KB. Offers the storage capacity and processing capability to execute actions which are unique in the environment of smart...
Read More »
ABB Introduces Ability Smart Sensor That Communicates Wirelessly
The ABB Ability™ Smart Sensor for dodge mounted bearings uses latest algorithms for assessing the condition of bearings from vibration and temperature condition and indicates potential problems. The sensor can mount easily to the bearing and communicates via smartphone wirelessly. It enables employees to access the health data of bearings in difficult to reach locations. The sensor helps in...
Read More »
ISO-Certified J&D Tube Benders Delivers Rapid Tubeline Fabrication Services
J&D Tube Benders' laser cutting and machining services provide accurate and complex features on tubes of all shapes and sizes. Check out the video to learn more!
Read More »