Circuits

Thermal Test Chip meets JEDEC standards.

TTC-1002 Thermal Test Chips deliver precise thermal loads to specific geographic areas of semiconductor package or PCB to simulate thermal performance characteristics of subsystem. Cell, which measures 2.5 x 2.5 mm, may be used individually or combined in matrix of up to 40 x 40. There is always periphery access for all heating and Kelvin enabled measurement connections, and strategically placed...

Read More »

Integrated Circuit is built in Silicon On Insulator technology.

Capable of generating output voltages of 1.8-2.4 V from input voltages as low as 0.3-0.35 V, S-882Z permits DC/DC converter to start operation with low input voltages. Pumped-up charge is stored on start-up capacitor, and when its voltage exceeds start voltage threshold, it boots step-up DC/DC-converter into operation. Devices are available in SOT-23-5 packages.

Read More »

Logic ICs sustain continuous operation from -55 to +175-

CMT-74XX Series is comprised of quad 2-input NAND, hex inverter, quad 2-input OR, quad 2-input AND, quad 2-input NOR, Dual D-type flip-flop with set and reset, and quad 2-input XOR. All components operate from 3.3-5 V over entire temperature range with input and output CMOS compatibility. Units are suited for oil and gas, aeronautics, and automotive applications, and are packaged in plastic...

Read More »

Burst Mode CDR SerDes is suited for GPON OLTs.

Burst mode CDR SerDes PHY, supplied in 172-pin LBGA package, can be operated in automatic or manual mode and lock to upstream data burst at 1.244 Gbps in less than 20 bits. Using its transmit and receive parallel ports in TTL I/Os, product is suited for development of FPGA-based OLT reference designs. It is also available for multi-channel integration into ASICs and can be configured to improve...

Read More »
An Introduction to Plastic Injection Molding
Sponsored

An Introduction to Plastic Injection Molding

We developed this eBook with designers, engineers and purchasing specialists in mind. It is written to provide a basic understanding of plastic injection molding presses, processes and costs. Our goal is to make our customers more knowledgeable about what goes into making a plastic part.

Read More »
ICs speed cable and satellite set top box development.

ICs speed cable and satellite set top box development.

STi5197 for cable STBs includes QAM demodulator while STi5189 for satellite STBs includes a QPSK demodulator; both products have common architecture for MPEG-2 audio/video-decoding and application-processing functions. Common architecture speeds product development and simplifies pc-board design. Each device supports relevant broadcast standards - STi5197 supports DVB-C including ITU-T J83...

Read More »
Integrated Synchronous Buck Regulator is rated to 6 A.

Integrated Synchronous Buck Regulator is rated to 6 A.

Operating from one 6.5-24 V supply to accommodate various non-isolated DC-DC designs, FAN21SV06 enables designers of telecom, graphics cards, and consumer electronics to optimize efficiency while conserving space. It incorporates controller, driver, and power MOSFETs in 5 x 6 mm MLP footprint and delivers up to 95% efficiency. Along with suite of protection features, this TinyBuck(TM) device...

Read More »

Capacitive Touch Button IC is suited for mobile devices.

Supplied in 3 x 3 x 0.85 mm package, AT42QT1040 brings capacitive UIs to mobile devices. Existence of 4 digital output channels enables per-channel indication on touch detection, and IC can also be configured using one channel as proximity sensor to enable hidden-until-lit UIs. To achieve immunity to electrical noise, QTouch(TM) charge-transfer sensing method employs spread-spectrum modulation,...

Read More »

Hot Swap Controller includes power good indication.

Consisting of Hall-effect current sensor with integrated charge pump, gate driver, and multiple levels of load fault protection, 12 V Model ACS761 provides hot swap control and short circuit protection in single IC without external shunt resistor. Resistance of internal current conductor is typically 1.5 mW, and fixed over current fault threshold is set internally to 40 A. PGOOD pins provide...

Read More »

Systems-on-a-Chip optimize VoIP and multimedia performance.

Based on 3rd generation IP communications technology, BroadcomÂ-® Persona(TM) Platform offers IP phone SoC solutions for each product segment. Each device features Gigabit or Fast Ethernet switch with packet filtering capabilities and physical layer devices to support high-speed networks, analog audio codecs, and DSPs which support PhonexChange(TM) IP telephony software suite. Software...

Read More »

All Topics