Burnishers

Tools

Portable Electric Burnisher polishes stainless steel.

Accommodating abrasive wheels from 4-4.5 in. in diameter and 5/8-4 in. wide, Model SE12-115 is suited for grinding, polishing, sanding, and removing scratches and rust. Unit is equipped with 10 A motor providing 1,200 W of power, 98 lb-in. torque, and no-load speed of 900-2,800 rpm. In addition to Vario Tacho Constamatic electronic speed stabilization, tool incorporates dust-deflection winding...

Read More »
High-Speed Floor Burnisher is powered by propane engine.
Burnishers

High-Speed Floor Burnisher is powered by propane engine.

Along with 21 in. pad to accommodate smaller spaces, 21 in. Answer Floor Burnisher has completely modular design, full cast aluminum body with centered deck, and adjustable wheels for fine tuning pad pressure. Kawasaki 603cc engine, rated to 3,600 rpm, drives pad at speeds to 2,000 rpm while emitting no more than 80 dB during operation. Floor buffer machine is suited for use in areas such as...

Read More »
Burnishers

Sugino's Diamond Tip Burnishing Tools Create Micro Finish Surfaces

Sugino Corp, (Itasca, IL) introduces their Cat's Eye Diamond Tip Burnishing Tool Line and Single Roller Superoll SR Type burnishing tool. The Cat's Eye is designed for long-life and wear when working materials raging from 45 Rockwell C Hardness up to 60 Rockwell C. The Cat's Eye can be used to create micro finishes on ID, OD, End Surfaces, Tapered Surfaces, R surfaces and Spherical surfaces on...

Read More »
Fresh Air Never Smelled So Good
Burnishers

Fresh Air Never Smelled So Good

Burnishing floors can be a dusty job. The machine is actually grinding the top layer of finish off the floor, removing heel marks and contaminants as it cleans but creating dust at the same time. Now the Tornado Industries® 2500B Clean-Air Glazer(TM) burnisher leaves floors shiny and clean without releasing dust and impurities into the air. The 2500B has a clean-air filtering system that...

Read More »
New UBT-B2 Universal(TM) Burnishing Tool from Cogsdill
Burnishers

New UBT-B2 Universal(TM) Burnishing Tool from Cogsdill

CAMDEN, SOUTH CAROLINA (December 12, 2008) - The UBT-B2 Universal(TM) Burnishing Tool is a new boring bar-style burnishing tool recently introduced by Cogsdill Tool Products. A smaller version of the original UBT-B1, the B2 is intended for use on smaller machines and in smaller bores greater than 1.50 inches (38mm). Universal Burnishing Tool designs are available from Cogsdill for use on any part...

Read More »
Special Twin Coin Punch Tool Achieves Chamfer Diameter and Location Specs, Greatly Reduces Costs
Machining Heads

Special Twin Coin Punch Tool Achieves Chamfer Diameter and Location Specs, Greatly Reduces Costs

Special tool based on Cogsdill recessing head design used a coining arbor to punch the hole and chamfer in the bottom of the reservoir in their master cylinders. The tool fed into the bore and then was offset, which caused the punch to make contact with the surface. They could only manufacture one punched hole at a time. The method by which the tool was offset caused deflection problems,...

Read More »
Tools

Nobur® JA Replaces Expensive and Time-Consuming Secondary Operations

Automatic Recessing tool pays for itself in two weeks as cutting and welding operations are eliminated MANUFACTURER OF SPECIAL COMPONENTS was producing a frame for a motion picture camera. The frame features tubes that slide together and must be fastened. They needed to countersink holes inside each end of a six-foot long tube to allow a screw head to be recessed below the tube ID. They were...

Read More »
Cogsdill's ZXTM Bottle-¬Boring Tool Outperforms The Competition
Boring Machinery

Cogsdill's ZXTM Bottle-¬Boring Tool Outperforms The Competition

Better chip evacuation, cutting support, and surface finishes special Cogsdill ZXTM bottleÂ-¬boring tool was designed to machine a 5.451 in. (138.46mm) diameter cavity bore and conical blend tapers (21˚ and 11˚), leading into a 3.794 in. (96.37mm) flow bore. The customer was honing the flow (pilot) bore for size.Awork length of 49.430 in. (1255.52mm) was required in order to machine the...

Read More »
Universal(TM) Burnishing Tool Offers Versatility to Burnish Multiple O.D. Surfaces
Burnishers

Universal(TM) Burnishing Tool Offers Versatility to Burnish Multiple O.D. Surfaces

Achieves finish better than required, with faster production JOB SHOP WAS SEEKING A BETTER FINISHING SOLUTION for their cylinder sleeves. They were using a finishing insert fed at the slow rate of .002 IPR (0.05mm/rev), followed by a polishing process, in order to achieve a finish requirement of 16 microinch (0.4 micrometer) Ra or better. Cogsdill recommended burnishing as a faster and more...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers