REGO-FIX Tool Corp.
Indianapolis, IN 46268
Share:
Toolholding System clamps tools without generating heat.
Featuring holder, collet, and mini-press generating 6 tons of force, powRgripÃ-® collet system relies on interference between holder and collet to generate clamping force, with run-out below 0.0001 in. Available from 1/8-Ã-¾ in., including metric sizes, interchangeable collets will hold both carbide and HSS tools. Less than 10 sec are needed to press in tool or remove it from holder, and...
Read More »
Toolholders are fine-tuned for balance up to 42,000 rpm.
Balanced by design, Q+- System of steep taper and HSK toolholders is suited for high-speed machining applications and offers taper selection comprised of CAT, BT, HSK, TC, and ISO versions. Products are created from case-hardened steel, have grooves to which balancing rings may be added, and offer TIR accuracy of 0.0001 in. or better. Steep taper toolholders are pre-balanced to G2.5 at 22,000...
Read More »REGO-FIX-® to Showcase Flexible powRgrip-® System at EASTEC 2006
Indianapolis, Indiana, February 21, 2006 - REGO-FIXÃ-® will be demonstrating its revolutionary powRgripÃ-® system and other products and solutions at EASTEC 2006. REGO-FIX will occupy booth #3145 at the trade show, which takes place May 23 - 25 at the Eastern States Exposition Grounds in West Springfield, Massachusetts. The REGO-FIX powRgrip system uses a toolholder and collet that allow...
Read More »Toolholder offers operational flexibility.
Featuring flexible design with complete tool rigidity, Zero-Z toolholder is pre-balanced to G2.5 at 22,000 rpm and comes with Hi-Q external clamping nut. Design also features flush collet nut, eliminating tool overhang. Suited for multiplex turning machines and small VMCs, product is compatible with CAT 40 taper and ER 32 series collets as well as company's tapping collets for tapping...
Read More »Coolant Flush Collets work with coolant-through tooling.
Offered in 0.1181-0.7874 in. dia, powRgrip coolant flush collets feature 3 equally staggered serrations to flush coolant through toolholding systems and ensure proper amount of fluid is reaching cutting tool and chips. Design flushes coolant along sides of tool and to tip of cutter, eliminating unwanted chip particulate. Collets, made of spring steel, are metallic-sealed for pressure capability...
Read More »Presetters have electronic parallel correction function.
Designed to be on shop floor next to machines, benchtop Toolmaster TM10 Presetters produce run-out less than 0.00008 in. with Needle Bearing Basket. Tool taper rides on needle bearings, which allows dust and debris to pass through. With 2% taper contact, debris or scratches in toolholder will not effect measurement. Units are suited for all tool measuring and presetting applications, and do not...
Read More »Tool Holding System is designed for high-speed machining.
Capable of reaching into deep cavities and machining challenging areas without compromising part accuracy or repeatability, powRgrip extensions are available in 120, 160, and 200 mm and allow use of tools from 2 mm to 3/8 in. Extensions feature holder, collet, and mini-press. With Swiss precision grinding TIR of less than 0.0001 in., system is compatible with REGO-FIX's PG 15 and PG 25 series...
Read More »Collet Holders feature keyless design.
Available in 4 models, BT Collet Holders are made from case-hardened steel and capable of up to 42,000 rpm. Units in ER Series come in standard and ultra-precision models and can clamp tool shanks from 0.0787-0.6299 in. Models in powRgrip Series clamp tool shanks from 0.0787-0.7874 in. and use mechanical properties of holder material to generate gripping force with run-out below 0.0001 in. All...
Read More »