Pulse Electronics
Suite #100
San Diego, CA 92128
Share:
DAS Absorber and Antenna Holder mitigate PIM.
To optimize installation, PIMinator-® Distributed Antenna Systems are available with DASACHOLDER above-ceiling antenna holder. Plastic holder does not interfere with aesthetics of building and does not induce passive intermodulation. Attaching to plastic holder or surrounding structures, DASACABSORBER helps mitigate effects of PIM sources by absorbing reflections on cellular radio frequencies in...
Read More »
High Isolation Switch Mode Transformers come in SMT packages.
Providing- reinforced insulation power supply compatible with MAXIM™ MAX253 to power RS-485/RS-232 transceivers, PH9185 series operates in- fixed duty cycle push-pull topology that delivers up to 3 W from- low-voltage source and- working voltage up to 4,000 V with 5,000 V isolation and 8 mm creepage. Products meet standard EIA481 requirements and may be used in industrial control systems,...
Read More »
Class H Line Driver Transformers support VDSL2 vectoring.
Compliant with Lantiq's Vinax V3 chipset, 30 MHz Models BX4289LNL and BX4289LNLT are used with Class H line driver to deliver high bandwidth over existing copper transmission lines.- Transformers drive data rates up to 150 Mbps/downstream and 100 Mbps/upstream on single line, supporting such services as HD IPTV, high-speed Internet access, multi-player gaming networks, and VoIP. Packaged in...
Read More »
In-Building Omni Antennas feature -155 dBc PIM rating.
With passive inter-modulation specification of -155 dBc at 2 x 20 W, PIMinators- meet demanding requirements of cellular operators and integrators of low PIM components for 2G, 3G, and LTE/4G bands worldwide. Ceiling mount Distributed Antenna Systems allow users to receive cellular coverage inside buildings. Measuring 8.27 in. in diameter, DASLTE500NF has 500 mm plenum rated coaxial pigtail with...
Read More »
Tunable LTE Antenna provides 9 bands.
Housed in metal chassis with dielectric antenna carrier, mCOMET combines 2 LTE MIMO antennas in same end of one device to provide 9 frequency bands of functionality in volume of 3.20 cc. Frequency bands for both antennas- include: low band of 698-960 MHz and high bands of 1,710-2,170 MHz and 2,500-2,690 MHz. Unit is intended for use in smartphones using RF chips with 2PDT antenna switch and...
Read More »
NFC Antenna complies with EMVCo 40 mm specification.
Measuring 35 x 50 mm with minimum thickness of 0.185 mm and 2 x 2 mm pad size, NFC Ferrite Sheet Antenna enables mobile devices to read data from up to 40 mm, supporting communication with other wireless devices for payments, access and control, credential storage/exchange, and content consumption. Antenna is constructed of thin ferrite with one-sided flex and thin adhesive. EMVCo specifications...
Read More »Dual Splitter Modules target VDSL2 applications.
Model B8891DVNL is used on rack cards found in DSLAMs or within roadside cabinets to combine or split plain old telephone service data from DSL data. Combining 2 central office splitter modules onto one platform, product minimizes component count on PCBs. It is RoHS-6 compliant and TR-127-compliant to support ADSL2 and VDSL2 applications, as well as compliant to China MII YD/T 1187-2006 ADSL2+...
Read More »Active GPS Antenna provides Global 3G functionality.
Housed in elliptical package measuring 100 x 50 x 8 mm, Model W4150GG5000 combines GPS ceramic chip antenna, low noise amplifier, and 3G antenna functions, including GPRS, GSM, UMTS, and WCDMA. Unit receives location information from GPS satellite and uses cellular network to transfer information to central control center or third party. 3G antenna covers frequencies of 824-960/1,710-2,170 MHz...
Read More »
DAS Absorber and Antenna Holder mitigate PIM.
To optimize installation, PIMinator-® Distributed Antenna Systems are available with DASACHOLDER above-ceiling antenna holder. Plastic holder does not interfere with aesthetics of building and does not induce passive intermodulation. Attaching to plastic holder or surrounding structures, DASACABSORBER helps mitigate effects of PIM sources by absorbing reflections on cellular radio frequencies in...
Read More »
High Isolation Switch Mode Transformers come in SMT packages.
Providing- reinforced insulation power supply compatible with MAXIM™ MAX253 to power RS-485/RS-232 transceivers, PH9185 series operates in- fixed duty cycle push-pull topology that delivers up to 3 W from- low-voltage source and- working voltage up to 4,000 V with 5,000 V isolation and 8 mm creepage. Products meet standard EIA481 requirements and may be used in industrial control systems,...
Read More »
Class H Line Driver Transformers support VDSL2 vectoring.
Compliant with Lantiq's Vinax V3 chipset, 30 MHz Models BX4289LNL and BX4289LNLT are used with Class H line driver to deliver high bandwidth over existing copper transmission lines.- Transformers drive data rates up to 150 Mbps/downstream and 100 Mbps/upstream on single line, supporting such services as HD IPTV, high-speed Internet access, multi-player gaming networks, and VoIP. Packaged in...
Read More »
In-Building Omni Antennas feature -155 dBc PIM rating.
With passive inter-modulation specification of -155 dBc at 2 x 20 W, PIMinators- meet demanding requirements of cellular operators and integrators of low PIM components for 2G, 3G, and LTE/4G bands worldwide. Ceiling mount Distributed Antenna Systems allow users to receive cellular coverage inside buildings. Measuring 8.27 in. in diameter, DASLTE500NF has 500 mm plenum rated coaxial pigtail with...
Read More »
Tunable LTE Antenna provides 9 bands.
Housed in metal chassis with dielectric antenna carrier, mCOMET combines 2 LTE MIMO antennas in same end of one device to provide 9 frequency bands of functionality in volume of 3.20 cc. Frequency bands for both antennas- include: low band of 698-960 MHz and high bands of 1,710-2,170 MHz and 2,500-2,690 MHz. Unit is intended for use in smartphones using RF chips with 2PDT antenna switch and...
Read More »
NFC Antenna complies with EMVCo 40 mm specification.
Measuring 35 x 50 mm with minimum thickness of 0.185 mm and 2 x 2 mm pad size, NFC Ferrite Sheet Antenna enables mobile devices to read data from up to 40 mm, supporting communication with other wireless devices for payments, access and control, credential storage/exchange, and content consumption. Antenna is constructed of thin ferrite with one-sided flex and thin adhesive. EMVCo specifications...
Read More »Dual Splitter Modules target VDSL2 applications.
Model B8891DVNL is used on rack cards found in DSLAMs or within roadside cabinets to combine or split plain old telephone service data from DSL data. Combining 2 central office splitter modules onto one platform, product minimizes component count on PCBs. It is RoHS-6 compliant and TR-127-compliant to support ADSL2 and VDSL2 applications, as well as compliant to China MII YD/T 1187-2006 ADSL2+...
Read More »Active GPS Antenna provides Global 3G functionality.
Housed in elliptical package measuring 100 x 50 x 8 mm, Model W4150GG5000 combines GPS ceramic chip antenna, low noise amplifier, and 3G antenna functions, including GPRS, GSM, UMTS, and WCDMA. Unit receives location information from GPS satellite and uses cellular network to transfer information to central control center or third party. 3G antenna covers frequencies of 824-960/1,710-2,170 MHz...
Read More »Power Line Communication Application Now Available on the Pulse Electronics Website
San Diego, Calif. - February 17, 2011 - Pulse Electronics Corporation (NYSE: PULS), a leading provider of electronic components, provides engineers with an application-based sales (ABS) tool for designing power line communication (PLC) applications. The PLC application diagram aligns key Pulse Electronics technology and product lines within the home automation and home networking market segments....
Read More »