Kin-Tek Laboratories    LaMarque, TX 77568 4202
May 10, 2012 Trace Source(TM) permeation tubes are used to dynamically blend calibration gas standards for Hazardous Air Pollutants (HAPs), such as phenol, toluene 2.4 diisocyanate (TDI), triethylamine, or naphthalene. When held at constant temperature, tubes emit constant flow of vapor. Diluting that flow with known flow of pure nitrogen or zero air forms low-pressure gas standard, and permeation tube flow is measured by monitoring rate of weight loss of tube. Mixtures are traceable to NIST.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Mar 12, 2012 Using Trace Source(TM) Permeation Tube, Span Pac(TM) H2O - SD adds concentration of water vapor into flow of dry matrix gas to create calibration standards for trace moisture monitors. Second dilution stage takes adjustable aliquot of primary mixture and dilutes it further with matrix gas. Two-stage dilution allows output concentration of trace moisture to be varied seamlessly over range of up to 10,000:1 from one permeation tube. System adds water vapor concentrations from 100 ppb to 5,000+ ppm.

Dwyer Instruments, Inc.    Michigan City, IN 46361
Dec 14, 2011 Supplied in hard carrying case to facilitate transportation, Model GCK-200CO-2000CO2 provides reliable flow of carbon monoxide (CO) and carbon dioxide (CO2) to calibrate Dwyer® gas sensing transmitters. Each kit includes span gas of 200 ppm CO and 2,000 ppm of CO2, reference gas of 99.99% nitrogen, 0.5 Lpm flow regulator, and tubing. Certificate of analysis and material safety data sheets are included for both gas cylinders.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Nov 09, 2011 Used for analysis of hazardous air pollutants, Trace Source(TM) Permeation Tubes emit constant flow of vapor to dynamically blend low-pressure gas mixtures. Emission flow measurements are traceable to NIST through fundamental measurements such as weight change, and temperature. Concentration can be adjusted by adjusting dilution flow rate. Applications include formaldehyde, hydrazines, ethylene glycol, cresols, naphthalene, and 15 other compounds not available as cylinder mixtures.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Sep 12, 2011 Combining FlexStream(TM) Automated Permeation Tube System and Secondary Dilution Module, FlexStream(TM) CF configuration creates adjustable concentration gas mixtures with constant output flow using permeation tube sources. Software adjusts dilution and aliquot flows to achieve desired concentration in final mixture, facilitating operation and allowing remote/automated control. Concentration adjustment over 200:1 range is possible without affecting output flow.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Apr 26, 2011 Trace Source(TM) 57FPK Gas Fed Permeation Tubes produce stable ppb calibration standards of arsine and other hydride impurities in polymerization-grade ethylene and propylene. Tubes are used with gas standards generating instrument to maintain them at constant temperature and flush them with olefin matrix gas. Flow of arsine from tubes mixes with this gas to create flowing calibration standard. Process enables concentrations from below 10 ppb to over 500 ppb of arsine to be produced.

Process Sensors Corp    Milford, MA 01757
Jan 10, 2011 Bench type design model BBS 1150 features emissivity of +0.995, 2 in. dia aperture, and uniformly heated spherical cavity. Offering user-selectable pushbuttons, PID controller allows accelerated adjustment of desired set point temperature. Product attains set point temperature and stabilizes, producing temperature reading to within 0.5°C for accurate calibration of instruments such as non-contact IR thermometers, thermal imaging camera systems, and spectrophotometers.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Jan 03, 2011 FlexStream(TM) Automated Permeation Tube System, combined with Secondary Dilution (SD) Module, creates variable concentration gas mixtures in constant output flow to facilitate test gas mixture production. Primary mixture concentration can be varied over 10:1 range in permeation unit, and adjustable aliquot of that mixture is added to constant dilution flow in SD module. Resulting concentration adjustability is over 100:1. Functionality accommodates contamination exposure applications.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Nov 09, 2010 FlexStream(TM) Gas Standards Generator creates mixtures by diluting emission from permeation tubes, or diffusion tubes, with inert diluent. In Trace Source(TM) permeation tubes, alpha-polyoxymethylene decomposes to maintain stable vapor pressure of formaldehyde and stable emission rate of formaldehyde. Formaldehyde emitted from tube is mixed with zero air in FlexStream(TM) instrument to form trace concentration gas standard. Emission flow measurements are traceable to NIST.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Sep 03, 2010 Offered as modular system, FlexStream(TM) uses Trace Source(TM) permeation tubes, which add precisely known concentrations of sulfur compounds to nitrogen, ethylene, or propylene matrix. It is configured with 2 permeation ovens and secondary dilution module for producing mixtures containing H2S, COS, and range of higher boiling sulfur compounds. Concentration can also be varied for multi-point calibration, and microprocessor system sets dilution flows and selects proper operating mode.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Apr 14, 2010 FlexStream(TM) dilutes emission from permeation or diffusion tubes with inert gas to create trace concentration - ppm, ppb, pptr - gas mixtures. Featuring internal microprocessor that sets operating mode and adjusts dilution flows to achieve desired concentrations, modular system also offers up to 6 independently controlled channels that can consist of permeation units or combination of permeation units and secondary dilution. Mixtures containing up to 48 components are possible.

Cal Sensors, Inc.    Santa Rosa, CA 95403
Jan 26, 2010 With output of 4 x 10^-2 W/cm² at 1 in. from filament, PIREPlus can be pulsed as source of blackbody radiation for near-to-far infrared applications at 180 Hz with 50% modulation depth. Radiating element consists of ultra-thin metallic foil with emissivity of 0.88. Designed to operate at max foil temperature of 1,000°K, PIREPlus emitter is offered with standard integrated reflector to provide near collimated and uniform radiation output.

Brookfield Engineering Laboratories, Inc.    Middleboro, MA 02346
Dec 30, 2009 Enabling calibration in glass-free environment, Plastic VisCal Kit includes 600 mL plastic beaker, 1 liter Silicone Viscosity Standard in plastic bottle, and metal lid for anchoring beaker in temperature bath. Reversible lid fits containers of various sizes. Using Brookfield Viscosity Standards with accuracy ±1%, operators can verify calibration of Brookfield Laboratory Viscometer/Rheometer.

Fluke Corp.    Everett, WA 98203
Oct 02, 2009 Fluke 6100B Power Standard provides voltage channel current drive suitable for calibrating energy meters taking power from voltage input. Suited for measurement devices for sinusoidal waveforms, Fluke 6105A offers 0.007% 1-yr energy accuracy to verify performance of various secondary standards. Both provide reference power and energy for instrument calibration and allow setups to be saved/recalled from within or from USB storage device. High-resolution 8 in. TFT display is included.

Palmer Wahl    Asheville, NC 28804
Sep 22, 2009 Wahl® Heat Spy Portable Calibration Black Body is used for single-point calibration verification and checking of IR instruments such as thermal imaging cameras and point IR thermometers. Ambient temperature black body features accuracy of ±.3°F. Housed in watertight IP67 carrying case, it includes NIST Traceable Certificate of Calibration and replaceable battery with 3 yr operational life.

Rigaku Americas Corp.    The Woodlands, TX 77381
Aug 04, 2009 Specifically designed to run on ZSX-Petro, Supermini, and Mini-Z Sulfur platforms, Petro-Pak implements ASTM 2622, ASTM 5059, and ASTM 6334 compliant methods for all hydrocarbon-based fuels. Package includes installation CD with programs and procedures for specific instrument, manual describing implementation and maintenance of package, calibration reference standards, set of drift monitor standards, and quality control standard for ongoing validation of methods.

Gigahertz-Optik Inc.    Newburyport, MA 01950 4009
Apr 27, 2009 Providing adjustable hemispherical light output, model ISS-8K-100-VAHP is based around 80 mm dia integrating sphere, which offers greater than 98% white-diffuse reflectance across visible and near infrared spectral range. It combines 100 W QH lamp, variable aperture, and interchangeable OD0, OD1, and OD2 attenuators, delivering output signal level step control from 0.1-100,000 cd/m². Product can be used as calibration standard for luminance and radiance measurement instruments.

Control Co.    Houston, TX 77258 8307
Feb 02, 2009 With 1¾ in. diameter and 3½ in. depth, Traceable® One-Shot(TM) single-use Conductivity Standards allow probe calibration to take place in polyethylene container, eliminating concerns about external container contamination. Standards accommodate virtually all conductivity probes and are suited for lab or field conditions. Each container is supplied with instructions, temperature compensation chart, traceability information, and Traceable® Certificate.

Labsphere, Inc.    North Sutton, NH 03260 0070
Jan 13, 2009 Available in 400 and 1,000 lumen models, Forward Flux Lamp Standards can be used to calibrate integrating sphere spectrometers for total forward spectral radiant flux responsivity from 350-1,050 nm. Each lamp standard is seasoned for 1% of rated life, and then screened for stability and repeatable performance, before transferring lumen directly from NIST lumen reference. Standards include calibration certificate and calibration data on CD-ROM.

Kin-Tek Laboratories    LaMarque, TX 77568 4202
Apr 08, 2008 Available with O2, CO, CO2, CH4, and C2H2, Trace Source(TM) 57 Series is used in Gas Standards Generators to dynamically blend ppm and ppb mixtures directly from pure gas. Tubes use controlled pressure of analyte vapor as permeate source, allowing very low boiling compounds. Achieving dilutions ranging from less than 103:1 to over 109:1 in single step, tubes are suitable for preparing trace mixtures containing atmospheric gases, light hydrocarbons, hydrides, and acid gases.