Test & Measuring Instruments

Test & Measuring Instruments

Synchro to BCD Converter has 0.01 deg resolution.

November 30, 2001

Module converts synchro or resolver inputs of 11.8, 26 or 90V @ 400Hz or 90V @ 60Hz into five decade BCD data representing angle with accuracy of 0.050 or 0.030 deg. Converters have isolated synchro inputs and zero offset adjustment. Digital outputs are TTL/CMOS compatible. Frequency range is 47Hz to 1200Hz. Operating temperature ranges are 0 to +70°C and -55°C to 105°C. Unit requires... Read More

Sensors Monitors & Transducers, Test & Measuring Instruments

Absolute Encoder handles tough environments.

November 30, 2001

Multiplexed Scaleable Absolute Encoder works in severe electrical and physical environments with high temperatures, vibration, and moisture. It converts up to 16 shaft inputs to BCD or binary information corresponding directly to shaft angle with accuracy of ±1 pt. in 3600. Data outputs are TTL compatible, and data transfer and data hold line are provided for interfacing to microprocessors and... Read More

Computer Hardware & Peripherals, Test & Measuring Instruments

Development Board features PC/104 form factor.

November 30, 2001

Constellation-20KE(TM) Development System provides support for one million logic gate APEX family PLD. It includes ISA and USB interfaces as well as flash programmable memory. ISA and USB connectivity allow designs to be directly downloaded from PC into PLD and then simulated using real-time hardware. System can be used as a Digital Pattern Generator, Bit Error Rate Tester, or Vector Waveform... Read More

Test & Measuring Instruments

Development Board suits PC/104+ modules.

November 30, 2001

DEV104+ development board for PC/104 and PC104+ modules is suitable for prototyping and embedded applications. It has 16-bit PC/104 Expansion bus, 32-bit PC/104+ Expansion bus, two 16-bit ISA Expansion bus slots, and two single device 32-bit PCI Expansion bus slots. Board can be powered with ATX or AT supply, and six LED lights indicate power supply output status. All pin-out descriptions are... Read More

Test & Measuring Instruments

Measurement System is ideal for water treatment facilities.

November 30, 2001

Accu4 online turbidity measurement system employs USEPA approved Method 2, 4-beam ratiometeric measurement technique to provide accurate low level turbidity measurement. Technique automatically calculates out interferences such as process color and sample chamber fouling. Set of diagnostics is loaded into T53 analyzer allowing assessment of system operational conditions. Read More

Test & Measuring Instruments

Viscometer converts GPC/SEC system into triple threat.

November 29, 2001

Model 270 Differential Viscometer/Light Scattering Dual Detector can be added to existing GPC/SEC system equipped with a concentration detector, instantly converting it into triple detector system. Triple detection is used for characterization of natural and synthetic polymers and proteins. It employs light scattering detector to measure absolute molecular weight and viscometer to measure... Read More

Sensors Monitors & Transducers, Test & Measuring Instruments

Benchtop Analyzer measures chrome coatings.

November 29, 2001

Portaspec benchtop wavelength dispersive X-ray fluorescence analyzer can perform multi-element sequential analysis in range of titanium through uranium. It is suitable for measuring coating weights of chrome and titanium pretreatment. Analyzer comes complete with easy-loading 2-position sample holder. PC Interfacing and software is also available. Read More

Test & Measuring Instruments

Turbine Flowmeter are designed for sanitary applications.

November 28, 2001

Flowmeter has 316 stainless steel tri-clamp endfittings and meets 3-A sanitary standard No. 28-02. It measures flow with 0.5% accuracy. Flowmeter is available in 1/4 in. to 3 in. size covering flow rates from 0.35 to 650 gpm. Read More

Test & Measuring Instruments

Visual Fault Locator accepts various optical connectors.

November 28, 2001

Pencil-style Model F6230A has universal connector that accepts any optical connector style with 2.5mm ferrule. Connector eliminates need for patch cable for direct connection to fiber under test if connector styles are dissimilar. VFL operates on single 1.5V AA alkaline battery and has "low battery" indicator. VFL output is from 1 mW laser at 650nm, providing visibility beyond 5 km. It includes... Read More

Test & Measuring Instruments

Humidity Analyzer monitors moisture in gases.

November 28, 2001

Model rh-plus MR 2350 relative humidity analyzer makes readings of 0-100%RH over temperatures of -15 to 85º C. Outputs are 0-20mA or 4-20mA, with system alarm relay and three adjustable relays with SPDT 2.5A contact. It has selectable failsafe mode, two-line LCD, and membrane-type pushbuttons for unit selection, ranges, setpoints, and special functions. Optional input permits external sensors... Read More

Test & Measuring Instruments

Portable Blackbody certifies infrared thermometers.

November 28, 2001

Model 9133 is factory calibrated and NIST traceable to be accurate to ±0.7°F, has heating and cooling times of about 15 min., and certifies IR thermometers over temperature ranges from -22° F to 302° F. It has 2.25 in. temperature controlled blackbody target with emmissivity of 0.95. Target accuracies of ±0.075°C can be achieved by using contact well, located behind the... Read More

Test & Measuring Instruments

Radar Level Gauge prevents gas leakage.

November 28, 2001

Micropilot M loop powered radar level gauge works on 2 operating frequencies of approximately 6 GHz and 26 GHz to provide level measurement solutions. Its unique algorithms provide real information on radar gauge status, regardless of operating conditions. It features 1 gas-tight, welded glass seal antenna, and menu-based operation and setup. Read More

Test & Measuring Instruments

Test Sockets have contact force of 30 g.

November 28, 2001

RF high-frequency CSP/BGA test sockets have spring probe contacts that provide 500,000+ insertion/withdrawal cycles with no loss of contact force or increase in contact resistance. Sockets offer short signal paths of 0.098 in. for 1.00 mm and 1.27 mm pitch packages. Self-inductance of sockets is 0.62 nH and contact resistance is 30m Ohms after 500,000 cycles. Propagation delay is 45 psec and... Read More

Test & Measuring Instruments

Conductivity Analyzers are for water/chemical processes.

November 28, 2001

Family includes Series 63 analyzer with predictive and reactive diagnostics; Series 53 general purpose analyzer; and Series 33 panel mount version for OEMs. Each has large backlit LCD that simultaneously displays measured conductivity values in Siemens/cm, total dissolved solids values in ppm, and concentration values in percent. Analyzers accept various contacting conductivity sensors and... Read More

Test & Measuring Instruments

Electrostatic Voltmeter measures semiconductor wafer surface.

November 28, 2001

Model 323 uses vacuum-compatible sensors, such as side view, end view, round or square body probes, to perform surface voltage measurements. It has 3-1/2 digit LED display and analog outputs at various scale factors. Analog outputs can be used to control ionization system for measured surface discharging. Applications include measuring semiconductor wafers, surface work functions, and disk drive... Read More

Test & Measuring Instruments

D/A Converter accommodates video and graphics.

November 27, 2001

Image-quality FMS3818 triple 8-bit DAC has conversion rate of 180MHz, making it suitable for display applications, including video, computer graphics cards and workstations, plus systems with XGA, SXGA, and UXGA resolution. It has power-down control to conserve battery power in portable equipment, double-buffered digital inputs for low distortion, and an onboard bandgap voltage reference. DAC is... Read More

Test & Measuring Instruments

I/O Modules are for programmable controllers.

November 27, 2001

I/O modules work with CompactLogix and MicroLogix controllers. 1769-HSC 1-MHz counter/encoder input module has 4 on-board 5-30V dc sourcing outputs for high-speed applications such as flow, speed, frequency and duration control, and length measurement and positioning. 1769-IF4XOF2 combination analog I/O module has 4 input channels and 2 output channels, with 1 unipolar voltage and 1 unipolar... Read More

Test & Measuring Instruments

Photon Counter works at speeds up to 500 MHz.

November 27, 2001

Dual precision PRM-400 Ratemeter/Photon Counter accepts TTL, NIM and ECL inputs, produces bar graph display on LCD, and has parallel, serial and GPIB interfaces. It counts every pulse without prescaling, has 10 µsec time base, and uses dual counter for background subtraction. Dual alternating counters provide zero dead time. It has large FIFO data storage and 40-bit deep counters. Applications... Read More

Test & Measuring Instruments

Porometer determines volume without using mercury.

November 27, 2001

Capillary Saturation Porometer determines pore volume and measures liquid permeability. For volume, sample is soaked in liquid that spontaneously fills pores. Pressure of non-reacting gas on top of sample is increased to displace liquid from pores, and pore volume, diameter, and volume distribution can be computed. To measure liquid permeability, pressure is increased, and permeability is... Read More

Test & Measuring Instruments

Pocket-Size Gauges measure thickness of materials.

November 27, 2001

Compact BNS series of dial gauges accurately measure sheet metal, card, paper and other materials up to 0.375 in. thick. Thickness measurement is displayed on clock face type dial within 0.001 in. Gauges fit comfortably in hand and slight pull on top plate opens chrome plated and lapped anvils, so material being measured can be inserted. Read More