Surface Guard, Inc.    Aurora, IL 60504
Jan 26, 2011 Surface Guard® 135 series provides temporary protection of textured or semi-matte finished metals and plastics. Coated with water-based acrylic adhesive system, polyolefin film adheres to surface, exhibits low adhesion build over time, and can be removed when protection is no longer required. Products are supplied on 1.5 mil Linear Low Density or 2.5 mil Low Density PE films; clear and tinted films are also available. Widths from 1-80 in. and roll lengths to 15,000 ft are available.

TenCate Advanced Composites USA, Inc.    Morgan Hill, CA 95037
Jan 25, 2011 Designed for out of autoclave vacuum cure composite structure, TC235SF addresses industry needs by providing low porosity, optimized surface appearance, and capability to self level under low cure pressures. Film provides cosmetically smooth appearance over thin skinned honeycomb core stiffened composites as well as solid laminates. Co-curable with 250 or 350°F prepregs, product maintains integrity over tight radiuses and is available in widths of 12-50 in.

Honeywell International, Inc.    Morristown, NJ 07960
Jan 21, 2011 Designed to meet NIJ.06 ballistic vest certification standard, Spectra Shield® II SA 4144 helps keep military and law enforcement personnel safe against variety of threats, including military-grade pistol rounds and fragments. Material incorporates Spectra® fiber, which is made from ultra-high molecular weight polyethylene using gel-spinning process. Material can reduce weight of personal armor systems by as much as 30%, optimizing mobility in dangerous situations.

LPS Laboratories, Inc., An Illinois Tool Works Co.    Tucker, GA 30085-5052
Jan 20, 2011 Protecting against seizure, heat-freeze, galling, rust, and corrosion, Food Grade Anti-Seize is NSF® Certified H1: Registration No. 143035 for use in food plants and conforms to FDA Regulation 21 CFR 178.3570 for incidental food contact. It has -65 to +1,800°F service rating and is not affected by metal contraction, expansion, or vibration. Non-staining and odorless, this product contains no metals, may be used with potable water, and meets MIL-PRF-907E.

Panolam Industries    Albany, OR 97321
Jan 20, 2011 Providing continuous color to edges of finished product, MelCor II laminate is comprised of multiple pigmented core paper layers impregnated into flexible thermoset resin at pressures exceeding 1,000 lb/in.² and temperatures approaching 300°F. Designers can thus incorporate beveled, wood, smoothed, or pinstriped edge into their products, while routers, engravers, or sandblasting equipment can be used to etch grooves, bands, or other patterns without compromising material's color.

WSI Industries LLC/N-Terpinal    Springfield, MO 65807
Jan 18, 2011 With formulation buffered to be safe to handle, N-Terpinal RS-DeScaler will dissolve rust and scale as well as etch concrete for coating systems. It does not contain any hydrofluoric acids or phosphates, is suited for cleaning metal and concrete, and may also serve as replacement for media and sandblasting. Depending on application type and severity, wait/soak times can vary from 1-5 min to 1-12 hr.

Rush Machinery, Inc.    Rushville, NY 14544
Jan 14, 2011 Designed for truing and dressing of flats, angles, and radii on diamond and CBN single wheels and multiple wheel packs, Models FC-250EX and FC-700EX feature PLC-controlled automatic dressing cycles with servo-driven dressing wheel infeed, power swing, and oscillation. Machines can be fully enclosed for operator safety and dust control. Constructed with one-piece cast iron base, machines include ExVision computer-driven vision system, automatic power zoom, and 2-axis DRO for measurement.

Mini-Circuits    Brooklyn, NY 11235
Jan 11, 2011 Featuring low-profile package, Model SYM-63LH+ provides IF response from DC-1,000 MHz and is useful in wideband system applications such as IED. Double balanced mixer utilizes core and wire transformers and diode quad in ring configuration. Transformers are designed to provide ultra wide bandwidth using simulation software together with proprietary transformer technology.

AGY    Aiken, SC 29801
Jan 06, 2011 Initially available on DE75 yarn, 947 direct sizing system for E-Glass yarns provides aerospace customers with opportunities to remove weight from traditional composite products while increasing tensile and compressive strengths. Fibers with 947 sizing can be woven into fabric and used in composite applications without additional finishing, eliminating related fabric integrity erosion. Currently, 947 sizing is compatible with epoxy and phenolic resins as well as thermoplastics.

TKF, Inc.    Cincinnati, OH 45203
Jan 04, 2011 Equipped with roll-to-roll chain driven live rollers (CDLRs), zoned accumulation conveyor is designed to handle medium- to heavy-duty loads and offers zone lengths designed to coincide with product lengths. Entire conveyor length is driven by one power unit, and each accumulation zone is driven by air-operated clutches controlled by photo-eyes and solenoids. Rollers are available in 1.9, 2.5, and 3.5 in. dia and widths up to 60 in, and weight loads to 6,000 lb are typical.

Columbus Instruments    Columbus, OH 43204
Jan 03, 2011 Equipped with internal MPU to perform all necessary calculations and signal sending, Pegas 4000 provides means to control up to 4 individual component gases using thermal mass flow controllers. Concentrations can be adjusted on-the-fly or dynamic mixing schedules can also be preprogrammed via included software. After operator enters total flow and concentration of each component gas, front panel rotometer shows flow of mixed gas. Bench/pilot scale mixer measures 13 x 11.5 x 7.5 in.

Baker Hughes Centrilift    Midland, TX 79703
Dec 31, 2010 Designed to reduce SOx air pollution that is created when hazardous hydrogen sulfide is burned, Petrolite SULFIX(TM) Additives help refineries comply with EPA's New Source Performance Standards, which limit permissible H2S in gas burned in flare to 160 ppm on rolling 3 hr average. Baker Hughes also provides services for control of flare gas H2S levels to help refiners select suitable additives, use correct injection system equipment and design, and implement appropriate monitoring program.

Baker Hughes Centrilift    Midland, TX 79703
Dec 31, 2010 Comprised of environmentally preferred fracturing fluids and additives, BJ SmartCare(TM) products meet technical performance and environmental compliance requirements. Qualification by independent expert environmental consultants was based on transparent, quantifiable, and standardized method of measuring environmental, human health, and physical risks associated with oilfield operations. Products are qualified for slickwater, linear gel, crosslinked, and viscoelastic fracturing systems.

Quadro Engineering Corp.    Waterloo N2V1A1  Canada
Dec 24, 2010 Accommodating liquid pharmaceutical processors interested in submicron emulsions, suspension milling, and micronization, Ytron® HV0-Emulsifier and Wet Mill provides benefits of high velocity (HV) milling at inline process capacity of 1-5 Lpm. There are 3 models, ranging from 7.5-60 hp, with capacities of up to 285+ Lpm. Each uses energy optimized tooling that operates at tip speeds to 70 m/sec. Sanitary high-speed mechanical seal eliminates potential trap areas around rotor shaft.

CertainTeed Corp.    Valley Forge, PA 19482-0860
Dec 22, 2010 Diamondback(TM) Tile Backer is reinforced with embedded glass mats for strength and moisture and mold resistance. It features polymer coating with textured surface that creates strong bond, helping to avoid tile slippage during installation. Eliminating need for moisture barrier, product can be used in bathrooms, kitchens, and other high-moisture residential and commercial interiors. Diamondback Tile Backer Type X is UL classified for fire resistance.

SoloPower, Inc.    San Jose, CA 95138
Dec 20, 2010 Measuring 0.88 x 3.05 m and weighing 15 lb, Model SFX3 thin film CIGS module is able to produce up to 260 W of electricity. With efficiency up to 12.1%, flexible CIGS module is IEC 61646 and IEC 61730 certified and holds ETL Mark certification to UL 1703 standard.

amixon, Inc.    Memphis, TN 38118
Dec 17, 2010 Featuring inclined and optionally sine wave-shaped agitator helix, Vertical Mixers provide residual removal rate of 99.983%. After output, residual content in single shaft mixer is only 240 g for 2 m³ of mixed product. Mixers can be operated with varying fill ratios from 10-100%, and just one mixer can be used for gentle homogenization of products as well as intensive de-agglomerate and micro-fine blending of high-viscous fluids.

Applied Plastics Co.    Norwood, MA 02062
Dec 17, 2010 Capable of 500°F continuous and 600°F intermittent use, APC Teflon®-Coated Nichrome Wire provides non-stick surface in variety of plastics and packaging processing applications. Product will outlast plain nichrome resistance wire and prevent melted plastic from building. Supplied on spools in standard 0.018, 0.020, and 0.036 in. sizes, wire is additionally suited for sealing, shrink wrapping, plastic sheet and styrofoam cutting, and acrylics bending equipment.

Surface Guard, Inc.    Aurora, IL 60504
Dec 17, 2010 Used during processing, assembly, and shipping, Surface Guard® 73 provides temporary protection of complex - textured, rugged, coarse - surfaces. Combination of polyethylene film coated with blend of aqueous adhesives results in masking that is soft and aggressive, while chemistry provides high tack and medium-high peel. Properties also ensure clean removal when protection is no longer needed. Film comes in widths from 1-80 in. and lengths to 15,000 ft.

Sherwin-Williams Co. c/o Ultimate Lead Systems    Berea, OH 44017
Dec 17, 2010 Suited for tank linings and piping under insulation, Cor-Cote® HT FF contains micaceous iron oxide for anti-corrosion and edge protective properties. Epoxy novolac amine is resistant up to 450°F in dry service environment and will perform in areas subject to wet/dry cycling up to 300°F. Available in 3 shades of gray, product can be applied to steel, stainless steel, or concrete and is designed for service with gasoline, fuel oil, diesel fuel, crude oil, ethanol, and other hydrocarbons.