Col-Met Spray Booths, Inc.    Rockwall, TX 75032
Aug 18, 2009 COL-MET EVO-4 has 4 towers that cover each corner of any standard-size booth and can be modified based on spray booth length and configuration. It runs on 15 A single-phase power with 110 V wiring harness included. Three Venturu nozzles create turbulence to disrupt laminar airflow during flash-off and three SS pipes with rotating air outlets position nozzles for optimal airflow settings. Air towers can be set from control panel to operate simultaneously or independently.

Schaeffler Group USA, Inc.    Fort Mill, SC 29715
Aug 17, 2009 Based on consistent refinement of high-grade NIROSteels, Cronitect® high-grade martensitic hardening steel provides corrosion resistance under extreme operating conditions, including dry running applications or when bearings come into contact with aggressive media such as water, salt spray, acids, and cleaning chemicals. Heat treatment process optimizes properties of base material, producing hard, wear-resistant surface zone with high corrosion-resistance and tough core.

Cox Sales Co.    Roanoke, VA 24016
Aug 17, 2009 Used for bindery operation, Blackjack Quick-dry Padding Adhesive suits printers who require accelerated cure times or want to apply just one coat of adhesive. Soft tear solution, characterized with optimal solids content and minimal water is recommended for many types of paper, from cardboard to tissue. White solution dries clear and is suited for tabbing, bookbinding, and interleaving carbon.

Milliken & Co.    Spartanburg, SC 29304
Aug 14, 2009 Designed to meet needs of automotive and appliance industries, Hyperform HPR-803 replaces high loadings of heavy mineral fillers, such as talc, while delivering balance of stiffness and impact strength. Product also offers high heat deflection temperatures and comparable surface finish to talc-filled compounds that cannot be achieved with chopped glass fiber reinforcement.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 With low fume generation rates, UltraCore® 70C Gas Shielded Flux-Cored Wire optimizes cleanliness and visibility while welding. Diffusible hydrogen levels are controlled at H8 AWS classification to provide resistance to hydrogen induced cracking. Optimized bead stacking and slag removal minimize clean-up time for multi-pass welding. Wire meets requirements of structural fabrication, heavy equipment, and ship building industries.

Lincoln Electric Co. Inc., The    Cleveland, OH 44117
Aug 10, 2009 Designed to meet requirements of heavy equipment, structural fabrication, and mining industries, gas-shielded UltraCore® 75C provides optimized stackability for welding thick steel sections. Basic slag system offers resistance to hydrogen induced cracking in many applications, including difficult-to-weld materials and restrained joints. Charpy V-notch test results are capable of exceeding AWS E70T-5C-JH4 impact requirements of 20 lbf-ft at -40°F.

Tempil, Inc.    South Plainfield, NJ 07080
Aug 07, 2009 Lot numbered for NIST traceability, Tempilstik° indicators make marks that melt within 1% of their rated temperatures. They are supplied in adjustable aluminum holder with pocket clip and come in 100+ temperature ratings systematically spaced between 100 and 2,500°F. Below its temperature rating, products leave dry, opaque chalk mark. When rating is reached, a liquid smear remains. Upon cooling, melted mark will solidify with transparent or translucent appearance.

Sherwin-Williams    Cleveland, OH 44115
Aug 06, 2009 Supplied as 2-package industrial coating, Tile-Clad® High Solids Mildew Resistant epoxy protects against mildew growth on exterior surfaces where dampness and humidity are of concern. It features gloss finish and is offered in variety of safety colors. Applications include clean rooms, laboratories, institutional kitchens, and chemical processing equipment where mildew growth must be guarded against in order to maintain operations.

Shin-Etsu Microsi, Inc.    Phoenix, AZ 85044
Aug 05, 2009 SINR series siloxane-based negative photoresist film, available in 12-100 micron thicknesses, will flow into vias to produce void-free dielectric fill and planarized surface. Suited for 3D Through-Silicon Vias (TSVs) and 2D wafer bonding applications, vacuum laminated dry films exhibit minimal residual stress with 90 MPa modulus that produces rubbery consistency and minimizes wafer bow. Dielectric constant is as low as 2.6, and built-in adhesion promoters ensure optimal bonding.

The Modal Shop, Inc.    Cincinnati, OH 45241
Aug 05, 2009 SmartShaker(TM) Models K2004E01 and K2007E01 are 4 and 7 lb force exciters, respectively. Devices measure 3.6 x 3.5 x 5.3 in integrate power amplifier in 3 x 3 x 0.75 in. space underneath. Portable units provide up to 7 lb pk sine force with ½ in. stroke covering broad frequency range up to 11 kHz. They feature suspension systems using carbon fiber composite leaf armature flexures, multiple gain settings, system mute, and overcurrent/overheating protection with automatic shutdown.

Quadrant Engineering Plastic Products Inc.    Reading, PA 19612-4235
Aug 05, 2009 Fluorosint® HPV offers optimized bearing performance (PV) that results in parts that can withstand higher loads and velocities, while its wear resistance (K factor) lends to extended wear life. Combining higher temperature resistance with low de-formation and low coefficient of linear thermal expansion, extreme grade of Fluorosint MT-01 provides engineers with design options for instances where compliance of PTFE needs to be balanced with precise control.

CHUKAR WATERJET, INC    ST. MICHAEL, MN 55376
Aug 05, 2009 Waterjet Cyclone abrasive removal system is cyclonic garnet extraction machine that removes up to 10 lb of garnet abrasive per minute from any waterjet cutting system. System features 1 yd hopper that requires only 25 ft² of floor space and it can be custom-sized for any waterjet tank. Able to operate unattended, the only moving parts that come in contact with abrasive slurry are 2 check valves at bottom of the pump, minimizing maintenance.

Pacor Inc.    Cinnaminson, NJ 08077
Aug 03, 2009 Designed for facilitated installation, UltraGard(TM) precut aerogel insulation cuts energy loss and extends pipe rack efficiencies in piping systems used in chemical and hydrocarbon processing operations. Construction consists of silica solids derived from gel in which liquid component has been replaced with gas and reinforced with nonwoven, glass fiber batting. Environmentally safe, hydrophobic product is offered in 5 or 10 mm thicknesses; 1½, 2, and 3 in. widths; and 59½ in. length.

Col-Met Spray Booths, Inc.    Rockwall, TX 75032
Aug 03, 2009 Portable COL-MET EVO-1 tower stand is suited for waterborne-based primer and basecoat applications in prep station setting. It includes 3 Venturu nozzles that create turbulence to disrupt laminar airflow during flash-off and 3 SS pipes with rotating air outlets that position nozzles for optimal airflow settings. Air speed is adjustable with multidirectional velocity cones, while manual timer lets user choose cycle time length. Unit includes 8 ft cord to plug into power source.

Bematek Systems, Inc.    Salem, MA 01970
Jul 31, 2009 Configurable to match user viscosity requirements, In-Line Wet Mixer features modular shear-action mixing head, which forces all product through several stages of high-speed rotors and stators to achieve consistent and repeatable finished product. Assuring total particle size reduction and homogenization, stainless steel mixer can handle viscosities from 100 cps and up with flow rates from 0.5-300 gpm, requiring dispersion down to 1 micron, with ±1% repeatability.

Bayer MaterialScience, LLC - Coatings, Adhesives & Sealants    Pittsburgh, PA 15205
Jul 30, 2009 Providing identification security, Makrofol® ID ProteXXion contains tiny metallic identification particles, which are distributed stochastically and can be arranged in customized patterns. Metal particles, which measure around 1/10 of a millimeter, can also be provided with alphanumeric information, logos, pictograms, and national emblems. Available in standard thickness of 100 µm, film is suited for IDs, passports, drivers' licenses, brand protection, and labeling.

Henkel Corp.    Madison Heights, MI 48071
Jul 30, 2009 Formulated for electrical, thermal, and mechanical assembly applications, Emerson & Cuming® CF3366(TM) delivers optimized adhesion at both room and elevated temperatures, offers electrical conductivity, and provides for uniform and void-free bondlines. Product also offers low-temperature, quick cure capabilities and ensures reliable RF ground plane performance, even in extreme environmental conditions.

Henkel Corporation    Rocky Hill, CT 06067
Jul 30, 2009 No-clean, halide-free Multicore® TFN700B(TM) is Newtonian-based, and, therefore, eliminates shearing conditions associated with traditional tacky flux formulations, delivering flux transfer consistency and compensating for varied process conditions. Non-hydroscopic and non-corrosive, product has built-in blue color system that enables optical recognition of flux by pick-and-place systems, allowing visual verification of flux volume before placement on top component of POP package.

Lanxess - Technical Rubber Products    Pittsburgh, PA 15275
Jul 30, 2009 Primal(TM) SB-110 and SB-155 waterborne polyacrylate dispersions can be used as sole binder in base coats or combined with select acrylic/polyurethane dispersions to obtain balanced property profile. Used to produce base coats for very soft leathers, Primal SB-110 is optimized for embossing properties, fastness to heat yellowing, cut-through resistance, and low surface tack. Primal SB-155 shares these properties but is suitable for high-covering base coats for embossed leather types.

Lanxess - Technical Rubber Products    Pittsburgh, PA 15275
Jul 30, 2009 Krynac M 3340 VP grade of synthetic nitril rubber features polymer additive Mesamoll, which is alkane sulfonic acid ester of phenol that offers low volatility and compatibility with nitrile rubber. Mesamoll is classified as neutral in terms of physiological and toxicological makeup. Grade, suitable for contact with food, is resistant to oil and grease.