Materials & Material Processing

Adhesives & Sealants, Materials & Material Processing

Encapsulant/Potting Material exhibits <1% shrinkage.

Dec 27, 2001

Ceramacast(TM) 510 aluminum oxide based, hydraulic-setting ceramic compound potting material can be used to encapsulate cartridge heaters and embed high temperature components to 3200ºF. Supplied as dry powder, Ceramacast 510 is bonded using calcium aluminate and as-cast. Its dried density is 180 lbs/ft3, and it exhibits exceptional thermal conductivity and dielectric strength of 75-100... Read More

Materials & Material Processing

Circulation Attritor can adapt to existing Q machines.

Dec 27, 2001

QL circulation grinding Attritor includes holding tank that is typically 10 times Attritor size. Specially configured arms speed up grinding and create more agitation. Unit's high circulation/pumping rate consists of holding tank contents passing through Attritor at ~8 times an hour. Grinding media for QL range in size from 3/32 to 1/4 in. in diameter. Typical media include chrome steel,... Read More

Materials & Material Processing

Static Mixer offers concave mixing elements.

Dec 27, 2001

Kenics® KMX static mixer's concave elements promote cross-stream flow. Each element is approximately 1 pipe diameter in length, and consists of multiple intersecting blades, which generate fluid layers as mixture flows downstream. Features include ASME-certified design and fabrication, diameters up to 24 in., no moving parts, and no external power or regular maintenance. Sheets of low... Read More

Materials & Material Processing

Flame Retardant Materials have no halogens.

Dec 27, 2001

Based on polytrimethylene terephthalate (PTT), RTP 4700 series glass reinforced, non-halogen, flame retardant polyester compounds are available with glass levels of 10% to 33%. It has flexural strength of 23,000 psi, dielectric strength of 500 V/mil, and HDT of 410°F @ 1.82 Mpa. It has UL 94 VO listing. Read More

Materials & Material Processing

Stripping Pot cleans magnet wire.

Dec 21, 2001

Magnet Wire Stripping Pot removes film insulations from magnet wires of all sizes, types, and configurations. Wires are dipped into stripping solution to remove insulation without causing any mechanical stress or abrasion to wire. Units are available in 2 models: DSP1 has temperature control and DSP2 has programmable control for selecting and maintaining exact temperature. Both models are... Read More

Materials & Material Processing

Boron Rings are oriented radially.

Dec 18, 2001

Made of sintered neodymium iron, single-piece Boron rings have radially oriented magnetic field. Because ring is single piece, and all grinding processes can be done prior to magnetizing and assembly. Polarization is single pole on outside with opposite pole on inside of ring, or alternating configuration with multiple poles on OD or ID. Parts can be magnetized in assembled state, or externally.... Read More

Materials & Material Processing

Extruder reprocesses low bulk density foam.

Dec 17, 2001

Scrapper(TM) dual-diameter extruder features large diameter screw section equipped with deep flights to mix and break down materials, while small diameter section is dedicated to melting, pumping and removing excess gases and volatiles. Feed section is cored for water-cooling and contains knives to assist in feeding of roll stock. Steel, fixed weldment base allows for mounting of smaller diameter... Read More

Materials & Material Processing

Fluoroelastomers feature reduced post-cure time.

Dec 17, 2001

Tecnoflon HS Family Fluoroelastomer products allow fabricators to reduce in-plant energy consumption, speed throughput of end products, and reduce need for inventory of their products. When injection- or compression-molded into O-rings, seals and other precision components, HS fluoroelastomers exhibit reduced mold fouling. They meet industry specifications, including MIL-R-83248C. Read More

Materials & Material Processing

Steel Turning Grades increase tool life.

Dec 17, 2001

KC9110 and KC9125 have coating bonding technology that can apply 3 main layers and several sub-layers of coating with total thickness of 18 microns. Grade KC9110 is ISO class P10 grade for finishing operations while Grade KC9125 is P25 class grade for universal machining on all types of steel. Both have coatings 25 to 75% thicker than company's conventional coated carbides and increase... Read More

Materials & Material Processing

Developer Replenisher is highly concentrated.

Dec 17, 2001

DR-501CR aqueous developer replenisher is a 1-part concentrate formulated for developing fully aqueous dry film photoresists and photoimageable solder masks. It is suitable for use in feed and bleed systems, requiring fewer additions than more diluted carbonate solutions. DR-501CR reduces volume of solution to waste treat. Read More

Chemicals & Chemical Processing, Materials & Material Processing

Corner Cushions protect products from damage.

Dec 13, 2001

Corner Keeper protectors are made from extruded polyethylene foam to provide non-abrasive surface areas and protection against multiple impacts. Protectors are fabricated from closed-cell polyethylene foam extrusions. Cylindrical profile is pneumatically cut to produce shape that mimics 3-dimensional, 90° angle, enabling protectors to fit around multi-planed edge of cube shape products. Read More

Materials & Material Processing

Desoldering Ribbon is an alternative to braided wick.

Dec 13, 2001

Constructed with 4 layers of fine precision copper screen wire mesh, Matrix® Desoldering Ribbon removes more solder than conventional wick. Dispenser with spring guide permits accurate placement while keeping operator's fingers safe from heat. Ribbon is available in 3 widths with rosin flux, no-clean flux, or bare copper. It features permanently static dissipative dispenser and is clean-room... Read More

Materials & Material Processing

T-Slotted Extrusions are available in 2 series.

Dec 11, 2001

Metric T-Slotted Extrusions, available in 25mm and 40mm series, feature smooth surfaces and ability to use either fractional or metric hardware. Typical industry applications include machine frames, cleanrooms, machine guards and enclosures, lighting, material handling equipment, and prototype equipment. All structures can be assembled using hand tools. Read More

Materials & Material Processing

Security Kit marks devices to thwart thieves.

Dec 11, 2001

Secure Marking Kit leaves invisible identification mark on servers, PCs, laptop computers, software CDs and other valuable office or personal assets. Kit includes hand held ultraviolet lamp, 3 UV marking pens, equipment inventory form and security labels. UV pens can mark wood, plastic, metal, glass, cloth and paper. UV lamp illuminates identifying marks. Kit comes with CD containing 38 security... Read More

Materials & Material Processing

Wear Resistant Strips protect conveyor rails and beds.

Dec 11, 2001

Richglide is made from Nylon 6/6 with molybdenum disulphide (MDS) added to increase surface lubricity and improve resistance to deformation at high temperatures. This makes strips suitable for protecting conveyor rails, beds and other products from surface scratching and marring. Read More

Materials & Material Processing

Plastic Extruders are designed for continuous operation.

Dec 11, 2001

Leister Hand-Held Plastic Extruders feature maximum molten output temperatures of 550°F, which are adjustable to ±2°F. They provide cold start protection, have dial selectable temperature settings, heat up fully in 3 minutes, and measure actual molten plastic in real-time. Units output 1/4 to 13 lbs per hour. They also feature 360° welding shoes and digital display of actual and set... Read More

Materials & Material Processing

Soldering Iron doesn't burn user's hand.

Dec 10, 2001

Miniature Antex Model 3U's heating element is directly under tip, so plastic handle stays cool. Tip reaches 750°F in 45 sec and recovers instantly after soldering each joint. Soldering iron comes with choice of 40 different tip styles, including spade, cone, chisel, needle point, and pyramids, making it suitable for various applications. Tool is 6.5 in. long and weighs less than 0.75 oz. Read More

Materials & Material Processing

Ionizer neutralizes static electricity.

Dec 05, 2001

Ionizing Point delivers high concentration of positive and negative ions to prevent jamming, tearing or dust attraction on slitting, winding, rewinding, ink jetting and silk screening applications. It incorporates stainless steel emitter and bracket for machine mounting. Unit fits 7/8 in. dia hole and extends only 1/8 in. from mounted surface. Static dissipation is fast, eliminating 5kV charge in... Read More

Materials & Material Processing

Urethane Foams feature reflective facings.

Dec 04, 2001

TUFCOTE® RM and SM urethane foams are designed for noise control applications where radiant heat may degrade acoustical materials. Aluminized polyester facings protect foam from soil and fluids. While SM facing is smooth, RM facing incorporates crisscrossed fiberglass filaments, which help to limit rips and tears if facing is punctured. Foams are available in rolls, sheets, or as custom... Read More

Materials & Material Processing

Polyurethane Dye Additive adds temp. color to clear coats.

Dec 03, 2001

Fade-A-Way Dye Additive, a translucent colorant, provides temporary color contrast between topcoat and base coat. It aids in uniform application of clear coat, and dissipates after approximately 72 hours, leaving only clear topcoat. Additive is suitable for use with Diamond-Clad Clear Coat applications in petrochemical, water, wastewater, and industrial applications. Read More