Elma Electronic Inc.
Fremont, CA 94538
Jun 16, 2009 Available in various colors and 51 sizes, Type 15 StyleBox enclosure supports 19 in. rackmount with/without handles, desktop with/without handles, portable case, and portable tower configurations. Handle design consists of 3 parts - top and bottom, which attach to enclosure, and 1U-7U centerpiece - and is offered in white, silver, or custom colors. Optionally, front can be recessed by 60 mm is available with or without perforated air-intake panel or solid panel.

Canfield Connector
Youngstown, OH 44514
Jun 03, 2009 Available in Mini, ISO, and Sub-Micro versions, Series 5000 protective enclosures are intended for electrical connection in conjunction with hydraulic and pneumatic solenoid valves. Modular design facilitates use where rapid installation and service are required. While ISO and 8 mm Sub-Micro versions connect valves using DIN 43650/ISO 4400 and EN175301-803:2000 specification, Mini and 9.4 mm Sub-Micro connectors are industry standards.

SprayCool
Liberty Lake, WA 99019
Jun 02, 2009 Targeted for use in ground vehicles, unmanned aerial systems, and rotor wing aircraft, Model MPE-3U provides environmental isolation to both commercial grade and rugged 3U cards. Enclosure can scale above 7 slots and is designed to meet industry standard designs for 3U VPX, cPCI/cPCIe and VME-64X, and proprietary electronics boards. Providing up to 100 W cooling capability per slot, enclosure operates in environments from -55 to +71°C and altitudes up to 55,000 ft.

Wireworks Corp.
Hillside, NJ 07205
May 05, 2009 As recessed low-voltage ring, Guardian Panel Mount can be mounted directly into wall by using mounting screws, fasteners, or toggle bolts. Custom connector panel is then attached to recessed flange, providing protected connectivity. When used with electrical box, it can be ordered in exact box size for surface-mount installations. Alternatively, panel mount can be ordered with flange 1 in. larger than box for flush-mounted applications. Most NEMA electrical box sizes can be accommodated.

Elma Electronic Inc.
Fremont, CA 94538
May 01, 2009 Suited for VME and other enclosure architectures, IEEE 7HP Front Panels provide alignment for adjacent cards and EMC protection for enclosure. Units are front anodized and rear-conductive with top and bottom cutouts for handle mounting. Anodizing front of panel provides scratch resistance and non-conductive material. Back and sides of panels are alodined, which is conductive but not scratch-resistant. Segmented and continuous gasket styles are available.

ITS Enclosures
Mt. Pleasant, PA 15666
Apr 13, 2009 QSR Enclosure is suited for Quick Serve Restaurant industry and can be adapted to any drive-thru application, such as banks and pharmacies. Able to withstand all outdoor conditions, it is available in multiple configurations with static and video display options as well as dimming, sunlight-readable displays. Thermal management features include venting design that optimizes airflow efficiency throughout enclosure to maximize cooling capabilities provided by AC unit.

L-Com, Inc.
North Andover, MA 01845
Apr 08, 2009 NEMA-rated weatherproof equipment enclosures come with installed mounting rails, this allows DIN rails and DIN rail mountable products, such as power supplies, protocol converters, industrial wireless access points, and Ethernet switches, to be housed inside enclosure. In addition to off-the-shelf NEMA rated enclosures, custom enclosures can be manufactured to specifications.

Safety Technology International
Waterford, MI 48327
Mar 26, 2009 Designed for use with STI-7500 series A, C, or F backbox and STI Stopper® II with 4 in. deep enclosed backbox, Model SUB-315 allows installer to place device onto plate and then mount plate and appliance into cover. Plate can be drilled to accommodate any type of device, such as keypad or control panel. Using plate, appliance can be assembled with any side or bottom tamper screws and then mounted into cover.

PC Enclosures
Wentzville, MO 63385
Mar 23, 2009 ICON, INFINITY, and ELITE digital signage enclosures are designed to protect plasma and LCD systems against theft, vandalism, water, dust, and heat. Used indoors or outdoors, they are sealed, lockable, and secure. Units are suited for use in public settings such as retail centers, industrial facilities, arenas, expo centers, airports, and subway/train stations.

OKW Enclosures, Inc
Bridgeville, PA 15017
Mar 09, 2009 UNITEC enclosures feature 2 inclined operating panels, at right angles to each other, which enable simultaneous input of data on one side and readout on other. Measuring 5.826 x 8.267 x 3.149/0.984 in., ergonomic enclosures feature 3-part design and are molded in ABS in off-white. Case parts interlock and are secured by 2 self-tapping screws. Utilized for desktop or wall mounted applications, units can be specified with or without battery compartment for 3 or 5 x 1.5 V AA cells.

Bulgin Components PLc
Barking Essex IG11 0AZ  United Kingdom
Feb 12, 2009 At 80 mm long and 53 mm deep, BE plastic enclosures are offered in 72, 106, and 139 mm widths for applications such as control stations and electrical/electronic control equipment. Corrosion- and impact-resistant products are available in choice of ABS (UL94-HB rated) or Polycarbonate (UL94-V0 rated), with respective temperature ratings of -20 to +85°C or +100°C. Along with 2 molded knock-outs with M20 thread, enclosures feature internal pre-molded PCB fixings and slots.

FSR Metal Products
West Paterson, NJ 07424
Feb 04, 2009 Designed to house hard switches, elastomeric pads, touch screens, and infrared pickups, OWB-CP1 Outdoor Wall Box allows for either surface, flush, or pole/pipe mounting using optional brackets. Unit comes with lockable doors and meets NEMA 4 ratings, so control panels are secure and protected from dirt, dust, rain, sleet, or snow. Doors are available with or without windows, and plates are included that accommodate 2- or 3-gang electrical plate mounting.

EIC Solutions, Inc.
Warminster, PA 18974-1157
Jan 08, 2009 Built to NEMA 4/4X construction standards in steel and stainless steel, DVR Cooler suits indoor/outdoor applications. It can house and protect DVR, as well as other 19 in. rack-mount electronics such as servers, routers, modems, switches, amplifiers, network gear, and communication equipment. Equipped with companion cooling system to provide protection for electronics, enclosure is customizable to accommodate different mounting requirements.

Hoffman
Anoka, MN 55303 1778
Jan 05, 2009 Desined to meet UL, NEMA/EEMAC, and CSA Type 1 standards, T1FLO(TM) uses active cooling ventilation system with 115 Vac fan, vent, filter, and thermostat to keep heat-sensitive drives and controls cool and protected. Off-the-shelf product is constructed with 14 gauge steel and offered with various airflow and enclosure size options. Other elements of construction include lift-off hinge door and solid or perforated accessory panels.

National Instruments Corp.
Austin, TX 78759-3504
Dec 12, 2008 Providing jitter-free communications, 8-slot Model NI 9144 is compatible with more than 30 analog and digital NI C Series modules as well as NI real-time controllers that have 2 Ethernet ports. Chassis also features 2 Ethernet ports, making it possible to daisy-chain multiple chassis from single controller. Using system of synchronized clocks, NI 9144 communicates deterministically across standard CAT5 Ethernet cable and can be distributed up to 100 m between chassis.

EIC Solutions, Inc.
Warminster, PA 18974-1157
Dec 10, 2008 DVR enclosure holds standard 19 in. rack-mountable DVR and protects it from harsh environmental factors such as dust, temperature, moisture, corrosion, and vibration. Equipped with companion cooling system, it is available in full-size, half-size, rack-mount, wall-mount, and custom configurations. NEMA 4 white-powder-coated steel and NEMA 4X SS configurations are also available.

FSR Metal Products
West Paterson, NJ 07424
Dec 09, 2008 Designed for AV, IT, and control applications, OWB-X Outdoor Wall Boxes are available in two box styles that allow for either flush or surface mounting. They feature flip up cable entry doors so that main cover door can be locked once cables are connected. Constructed in NEMA-4 style, boxes have integral locking doors in brushed aluminum. Internal connector mounting styles handle standard gang plates, IPS inserts, or XLR type connectors.

Elma Electronic Inc.
Fremont, CA 94538
Nov 21, 2008 MicroTCA solution in 19 in. rackmount 3U MicroSlim(TM) design offers 12 AMC, 2 MicroTCA carrier hub, 1 J-TAG switch module, 2 power modules, and 3 spare slots. There are also 4 HDD slots with SATA connectivity. Chassis accepts cards in single module/mid size (75 mm high x 4 HP wide), and chassis configuration can be customized to allow double modules (150 mm) and compact (3 HP) or full size (6 HP) modules. Internal cooling units produce 42 cfm each.

Bud Industries, Inc.
Willoughby, OH 44094
Oct 31, 2008 Available with or without integral battery compartment, Grabber Style K features soft ribbed-rounded sides that ensure secure, comfortable grip. Unit blends T- and rectangular-shaped enclosures, optimizing room for internal components. Made from high-impact-resistant black ABS plastic with UL94V-0 flammability rating, enclosure comes complete with top cover, bottom cover, battery door, and assembly hardware. Recessed top is suitable for label or keypad.

AD Products Co.
Cleveland, OH 44135
Oct 27, 2008 Available in 10 sizes ranging from 6 x 6 x 4 to 20 x 16 x 10 in., Premier Series is both NEMA 4X and IP66 rated with temperature range of -40 to 250°F. Hinges and latching are located on outside of sidewalls with no penetration into enclosure, eliminating risk of compromised protection. Gap areas are minimized to inhibit accumulation of dust, dirt, and other debris, which is critical for environments such as food processing and chemical processing.