Controls & Controllers ->
Engine & Motor Controls & Controllers ->
(Showing headlines 1 - 19)
Motor Control Centers improve uptime and safety.
Pittsburgh, PA 15108
May 28, 2013
XT motor control center (MCC) utilizes 24 Vdc control power for commercial, industrial, and OEM applications. Along with optional communications and arc preventative FlashGard® technology, solution is designed to support improved uptime and safety with power control. Communications-enabled versions let customers configure, control, and monitor their systems, enabling problems to be addressed before they cause downtime or excessive energy waste.
Automatic Start/Stop helps diesel engines conserve fuel.
Volvo Penta Of The Americas, Inc.
Chesapeake, VA 23320
Apr 04, 2013
Automatic start/stop option for Volvo Penta industrial diesel engines can achieve fuel savings of 5% or more by switching engine off when idling and consequently helps reduce emissions and noise. When machine's engine idles, this option turns engine off after pre-set time (usually 5–10 sec). Engine starts immediately when driver activates any of machine's controls, and work can continue. Start/stop capability can be deactivated or reactivated as needed.
Motor Control Centers feature embedded EtherNet/IP capabilities.
Milwaukee, WI 53204
Dec 03, 2012
With features of integrated EtherNet/IP network, medium-voltage CENTERLINE Motor Control Centers provide seamless information exchange between plant-floor and business-level systems. Premier Integration lets users configure and commission MCC with Rockwell Software Studio 5000, helping to eliminate errors associated with redundant programming. By allowing users to access information remotely, Ethernet connection lets personnel safely monitor, troubleshoot, and diagnose MCC.
Motor Control Center addresses causes of arc flash incidents.
Zurich CH-8050 Switzerland
Sep 07, 2012
MNS-MCC Low Voltage Motor Control Center offers plug-in type, withdrawable type, and full height unit technology, with up to 4,000 A horizontal bus and 1,600 A vertical bus. Meeting UL 845, CSA C22.2, and IBC-2006 standards, design is available in unit types that include starters, softstarters, VFDs, as well as mains and feeder breakers. Ability to remove unit - with door closed and without any tools or disconnecting any wires - encourages work to be performed outside arc flash boundary.
Controller/Monitor Combination protects industrial engines.
Basler Electric Co.
Highland, IL 62249
May 28, 2010
To facilitate industrial engine control/monitoring, IEM-2020 Industrial Engine Module provides engine protection, metering, and J1939 communications from one package. BESTCOMSPlus, also included, offers programming and setup software for remote control and monitoring as well as programmable logic and USB communications. Supplied in ruggedized and fully potted design, module provides 16 programmable contact inputs, 7 contact outputs, and 8 optional programmable 2 Adc contacts.
Scalable Kit facilitates tractor management.
Bosch Rexroth Corp.
Hoffman Estates, IL 60192-3707
Jul 31, 2009
Designed to help increase functionality and comfort of tractor, scalable kit satisfies all requirements of integrated tractor management. It includes electronic control units (ECUs), application software, electronic joysticks, displays, and range of valves. Able to electronically reproduce required tractor functions, kit is characterized as high performance due to 32-bit TriCore technology and 150 MHz clock frequency.
Motor Control Center protects against arc flash hazards.
Rockwell Automation / Allen-Bradley
Bloomington, MN 55438
Jan 07, 2009
Engineered to IEC 60439-1 and IEC 60529 standards, CENTERLINE 2500 features ArcShield option to protect against internal electrical arcs, and can withstand arcing durations up to 300 ms. ArcShield provides pressure relief system that exhausts gases through top of enclosure, away from personnel, without front ventilation. Offering 3- and 4-pole bus bar power systems, center includes variable speed drives, soft starters, electronic overload relays, and built-in DeviceNet network.
I/O Module features 18 digital inputs and CAN output.
Axiomatic Technologies Corp.
Mississauga, ON L4Z1Z8 Canada
Jul 09, 2008
Operating on 12 V or 24 Vdc input, Model AX030300 features IP67 packaging and connectors for harsh environments. Ten digital inputs are user-selectable as active high/active low, while 8 digital inputs are user-selectable as active high/active low, disable input, PWM signal, pulse, or counter. Equipped with Windows-based Electronic Assistant(TM) for configuration, saving, and writing settings, AX030300 is suited for engine controls for power generation, co-generation, and stationary power.
Engine Panels utilize J1939 CANbus protocol.
LOFA Industries, Inc.
Roswell, GA 30076
Dec 14, 2007
Housed in NEMA 4X polycarbonate enclosure with clear lockable door, CANplus 600 provides quad-gauge viewing with choice of up to 16 gauge readings. It includes heavy-duty IP64 key switch and IP67 rocker type throttle switch. Providing universal automatic start/stop platform for electronically and mechanically governed engines, CANplus 750 offers same features as CANplus 600 with additional options. Built-in wireless telemetry communication via Messenger module enables remote engine monitoring.
Electronic Engine Control features compact form factor.
Glendinning Marine Products, Inc.
Conway, SC 29526
Mar 02, 2007
Designed for multi-engine outboard fishing machines as well as stern drive and inboard boats from 23 ft and up, Smart Actuator II(TM) is capable of controlling 3 engines with 2 handles at up to 6 stations. Features include Automatic Engine Synchronization calibration procedure, choice of control heads including handheld remote (optional), plug and play installation, and 12 or 24 V capability.
Motor Control Center meets IEC 60439-1 and 60529 standards.
Milwaukee, WI 53204
Jan 17, 2007
Offering remote monitoring access capabilities on- or off-site, Allen-Bradley CENTERLINE 2500 motor control center (MCC) features IntelliCENTER software. System enables real-time MCC diagnostics and monitoring over DeviceNet, ControlNet, or Ethernet, promoting access to critical motor status information and facilitating information sharing for predictive maintenance, troubleshooting and safety. Modular system features 3- and 4-wire bus bar power systems.
Motor Control Center protects against arc flash hazards.
Milwaukee, WI 53204
Nov 06, 2006
CENTERLINE 2100 low voltage motor control center (MCC) with ArcShield option reduces risk of injury caused by internal electrical arcs. ArcShield features enclosure and arc-containment door latches that allow internal pressure relief and help keep doors from unlatching during arcing fault. It helps contain arc faults with horizontal bus rating (maximum 1,200 A bus) and small main disconnects, which help reduce amount of let-through energy within MCC.
Gas Abatement System achieves DREs above 95%.
San Jose, CA 95119
Aug 04, 2006
Powered by electric heaters that completely eliminate use of methane, Alpine-S is capable of abating all process and PFC gas emissions with destruction and removal efficiencies (DREs) of over 95% for both chemical vapor deposition and etch applications. Flameless, catalytic decomposition reactor operates in range of 850-950°C, while vortex device removes heat, particles and water-soluble acids, and helps to extend preventive maintenance cycle times.
Retrofit DPF is suited for European independent aftermarket.
Lake Forest, IL 60045
Jun 29, 2006
Walker® retrofit diesel particulate filter (DPF) features lightweight foam filter coated with precious metals. Unit combines catalytic converter and DPF into one unit, facilitating replacement of catalytic converter with DPF without adding additional weight or disturbing vehicle's entire NVH (noise, vibration, harshness) profile. Suited for most available diesel vehicles, DPF is fully homologated and installs without need to involve engine electronics.
Emissions Reduction System suits gas-fired kilns and ovens.
Precision Q Systems, LLC
Westerville, OH 43081-1886
Aug 20, 2004 Designed for gas-fired heat treating furnaces, NGEA-4-3000 delivers up to 70% drop in NOx emissions coupled with 5% increase in fuel efficiency. OSCOM (utilizing Oscillating Combustion Technology) reduces NOx by creating successive fuel rich and lean zones of combustion within flame envelope. At optimal frequencies and amplitudes, flame temperature is reduced, resulting in lower NOx with same energy input. OSCOM system installs in few hours and integrates with existing control system.
Emissions Solution suits diesel/gas engine applications.
Universal Silencer, A Fleetguard/Nelson Co.
Stoughton, WI 53589 0411
Jul 21, 2003 Combination silencer/catalyst utilizes one of two catalyst capturing techniques within silencer shell: a gasket-wrapped catalyst module or a torturous path configuration with serpentine interlocks around catalyst. Both designs completely seal silencer and ensure that exhaust gas passes through catalyst. Product is available in 4 performance grades with overall attenuation to 40 dB. Base catalyst housing packages are large end-in, end-out configured units.
Vehicle Control System suits small spark ignition engines.
Synchro-Start Products Inc.
Niles, IL 60714 3433
Apr 25, 2003 APECS® 5000 consists of programmable control system that has engine protection and diagnostic features. Unit provides engine/ground speed control, rate of acceleration control, drive-by-wire operation, variable speed operation, and power take-off operation. Product also offers universal speed input, stepper motor actuator, status LED, and sealed, waterproof connectors. System is suitable for all-terrain and utility vehicles, golf cars, and turf and ground maintenance equipment.
Catalytic Purifiers suit all Bobcat construction equipment.
Nett Technologies Inc.
Mississauga, Ontario, L5B4A7, CD Canada
Jun 20, 2002 Direct-fit catalytic purifiers replace one section of original exhaust system, eliminating requirements of cutting and welding. They reduce diesel particulate and hydrocarbon emissions responsible for characteristic diesel smell and eye irritation. OSHA and MSHA compliant, purifiers reduce CO emissions by over 90%, and remove 20-50% of total particulate matter emissions.
Control System optimizes engine performance.
Waukesha, WI 53188
Dec 05, 2001 Engenius ESM Engine System Manager, directed by Engine Control Unit (ECU) monitors speed, pressure, temperature and other engine conditions; controlling ignition timing, speed governing and stop/start functions. It also provides diagnostic help and fault logging when requested. System can be packaged to instantly communicate to Internet server, computer, phone or pager via satellite, cellular connection, radio frequency device or land phone line.
(Showing headlines 1 - 19)
Latest Products in the News
Goodhart Sons, Inc. - July 30, 2014
National Installer & Fabricator Completes Major Baghouse Upgrade
Stride Tool: Imperial Div - July 30, 2014
Stride Tool Inc. Takes Gold for its Imperial iManifold
Advanced Chemical Co. - July 29, 2014
Advanced Chemical Receives OHSAS Certificate
Aerovox Corp. - July 29, 2014
New Aerovox Technology Addresses Capacitor Performance in High Temperature Power Electronics Applications
Battenfeld-Cincinnati Co. - July 29, 2014
Evergreen Alpha Now Even More Compact
GEA Barr-Rosin - July 29, 2014
New Application for GEA Barr-Rosin Technology Achieves Better Quality and Reduced Explosion Risk when Drying Amino Acids
Southland Equipment Service, Inc. - July 28, 2014
Southland Equipment is Offering Extended Limited Warranty Plans for TCM by UniCarriers® Brand Products
Linde LLC - July 28, 2014
Linde's Healthcare Division to Display new Hospital Services Platform at the National ASHE Conference in Chicago
Profit Tools, Inc. - July 28, 2014
Profit Tools Intermodal Trucking Solutions Consistently Delivers ROI for its Customers
Shop-Pro Equipment, Inc. - July 28, 2014
"The Shop of Tomorrow" at NACE Expo 2014 to Include the Mobile Work Station®
More Products in the News...