Company News

CS Unitec, Inc.

22 Harbor Ave., Norwalk, CT, 06850, US

  • 203-853-9522
  • 800-700-5919

Public Relations:
Kim Bakowski
Les Howe Associates
Phone: 860-267-6651
E-mail this person

Share Like Tweet Add Email

Latest New Product News from
CS Unitec, Inc.

Machinery & Machining Tools

Rig-Mounted Core Drill offers multi-speed operation.

January 27, 2015

Used for drilling up to 14 in. dia holes in concrete, reinforced concrete, asphalt, and natural stone, 77 lb EBM 352/3 PSA employs 20 A motor and rugged gearbox with drilling speeds of 230, 500, and 1,030 rpm. Internal oil pump lubricates gearbox and shaft for extended life. Along with soft start and overload protection, features include mechanical slip clutch that provides protection in case of jamming. Screw jack for bracing is also included along with 39 in. tall anchor stand. Read More

Portable Tools

Hole Saws drill metal quickly and cleanly.

December 11, 2014

Used with hand-held drills, 1- and 2-Series Tungsten Carbide-Tipped (TCT) Hole Saws cut clean holes without grinding core. For cutting 9/16–4 in. dia holes up to 1 in. deep, 1-Series Hole Saws include center pilot drill. Cutters up to 3¼ in. dia feature 3/8 in. shank, while 3 5/16 in. dia and larger cutters feature ½ in. shank. For drilling 9/16–1 3/8 in. holes up to 9/16 in. deep, heavy-duty 2-Series Hole Saws feature spring-loaded pilot pin and milled 3-flat shank that fits ½ in. chucks. Read More

Materials & Material Processing

Portable Mixing Station minimizes airborne dust.

December 5, 2014

Featuring integrated dust extraction port, MEGA HIPPO® PMH 80F-RL minimizes airborne dust while mixing when connected to industrial vacuum. Easy-roll Trolley and balanced Easy-tilt Cradle allow one person to mix, transport, and accurately place up to 23 gallons of material at same time, boosting productivity. Equipped with two 8½ in. dia mixing paddles and 15 A/1,800 W, 2-speed motor, station is suitable for mixing cement screeds, overlay/underlay, textured coatings, sealants, and adhesives. Read More

Portable Tools, Machinery & Machining Tools

Portable Magnetic Drill features multi-axis positioning.

October 23, 2014

Used for job site drilling, boring, and slotting applications, MAB 800 KTS features infinitely variable torque control, servo-assisted drilling, 10 in. stroke, and full-wave electronics. Multi-axis positioning capability lets drill be adjusted up to 2 5/32 in. forward/backward and up to 4 ¾ in. left/right after magnet adheres to surface. In addition to cutting holes up to 2 3/8” dia, capabilities include twist drilling up to 1 in. dia. and tapping up to 1 1/8 in. dia. Read More

Portable Tools

Portable Magnetic Drill can be converted to standard drill press.

September 8, 2014

Featuring 8.2 A motor and no-load speed of 450 rpm, MABasic 200 drills up to 1¼ in. dia, 5¾ in. depth with annular cutters in structural steel and other metals. This heavy-duty, single-speed, 14¼ in. tall, 27 lb tool accepts cutters with ¾ in. Weldon Shank. With optional chuck, product converts to standard drill press with 6 1/3 in. stroke for conventional twist drilling up to ½ in. dia. Other features include internal lubrication system and Electronic Safety Shutoff Sensor. Read More

Portable Tools

Pneumatic Chain Saws feature patented chain brake.

August 22, 2014

Equipped with 4 hp motor that consumes 92 cfm of air at 90 psi, Series 5 1026, 5 1027, 5 1028, and 5 1029 are available with cutting capacity of 15, 17, 21, or 25 in. Units include Armor Tipped Guide Bar, Super Chisel saw chain 404 pitch, two separate oil lubricating systems for chain and motor, and chain brake that stops chain movement during kickback or repositioning of saw during cutting. Saws are ATEX Classified for safe use in hot work areas, Ex zones, or hazardous environments. Read More

Machinery & Machining Tools

Walk-Behind Floor Grinder is capable of dust-free operation.

July 23, 2014

With 20 A/110 V motor and no-load speed of 1,380 RPM, heavy-duty EBS 235 removes epoxy, paint, and other hard coatings from such surfaces as concrete, screed, and natural stone before new paint or coatings are applied. This 9 in., 84 lb unit with height-adjustable chassis features dust extraction port and brush shield that allow for dust-free grinding when attached to industrial vacuum system. By removing side portion of dust guard, operators are able to grind directly to edge of work area.
Read More

Machinery & Machining Tools, Services

Core Drill creates holes from 1/4 to 2 5/8 in. dia.

July 23, 2014

Weighing 7 lb, END 1550 P Wet Diamond Core Drill creates holes in natural stone, tiles, porcelain, stoneware, and glass without shock, dust, or vibration. Unit is powered by 13 A variable-speed motor that operates with no load speed of 1,800–4,400 rpm. For corrosion-free wet operation, drill features integrated water supply with flow control and stainless steel spindle. Changing drill bits and removing center core is accomplished via standard quick-lock adapter or 5/8 in. x 11 UNC threads. Read More

Machinery & Machining Tools

Multifunctional Tool performs blending and finishing tasks.

July 17, 2014

Applicable to tasks from rough grinding and blending to polishing up to mirror finish, VARLIEX® WSF 1800 employs 15 A (1,710 W) motor with tachogenerator feedback technology and features infinitely variable speed control (2,000–7,600 rpm). Latter extends service life of abrasive disc, prevents glazing of disc and heat deformation of work piece, and reduces noise. EASY-LOCK clamping nut and spindle lock button let user change discs in seconds and without tools. Read More

Machinery & Machining Tools, Services

Chop Saw (14 in.) can dry cut metal pipe, plate, and profiles.

April 23, 2014

Without requiring lubrication or manual deburring, Model 9435 Premium Super Dry Cutter saws up to 6 in. depth at 90° in stainless steel, ferrous and non-ferrous metal, plastic, aluminum, and more. Bevel cuts up to 4 ¾ in. at 45° can be achieved with quick-release, heavy-duty vise, and 19 A, 115 V motor delivers free cutting speed of 1,400 rpm. Supplied with 14 in. 90-tooth Tungsten Carbide Tipped (TCT) blade, saw also features depth stop, safety-locking pin, and protective shield. Read More

Machinery & Machining Tools

Dry-Cutting Circular Metal Saw uses 12 3/4 in. blade.

March 8, 2013

Featuring 12 ¾ in. dia carbide-tipped blade capable of cutting 4 ¾ in. deep, 8320 BigSaw2 is powered by 16 A motor that delivers free cutting speed of 1,400 rpm and features motor overload protection to prevent motor burnout. Portable metal saw cuts through steel, sandwich panels, conduits, metal pipes, and more without use of coolant. Cuts are burr-free and cool to touch within seconds. Side-mounted tilt tray for chip disposal and dust collection port are also standard. Read More

Construction Equipment & Supplies

Floor Scabbler prepares concrete without damaging substrate.

February 19, 2013

Designed with 11 one-piece piston Tungsten Carbide-tipped bush hammer heads that supply 24,000 total light blows/min, MHS11 Model 159.6051 provides concrete keying and laitance removal without damaging substrate below. Pneumatic floor scabbler has cutting width of 9 5/6 in. with production capacity of approximately 100 ft²/hr. Operating from single compressor and consuming 55 cfm of air at 90 psi, system includes 3-point vibration damping system and vacuum dust shroud to minimize hazardous dust. Read More

Mechanical Power Transmission

Reversible, 4-Speed Drill Motor serves driving applications.

January 11, 2013

As 20 A electric drill motor with 4-speed gearbox offering load speeds of 80, 130, 360, and 570 rpm, EAU 34/4 CB is designed for continuous use in driving machines for turning operations that require torque up to 203 lb-ft. Oilbath gearbox provides permanent lubrication, and control box includes on/off switch and switch for forward/reverse direction. Available in 120 and 220 V variants, 19.5 lb motor offers 1 ¾ in. dia max twist drilling capacity and 1 5/8 in. max tapping capacity. Read More

Portable Tools

Non-Sparking Torque Wrench can be used in hazardous areas.

October 10, 2012

Made from Copper-Beryllium, Non-sparking Torque Wrench eliminates risk of sparks at sites where explosive atmospheres may be present. This non-magnetic and corrosion-resistant tool, offering click mechanism for turning clockwise and counterclockwise, has clockwise torque range of 22–120 lb-ft, ½ in. square drive, and 18 ¼ in. long lever handle. Design enables use in Ex Zones 0, 1, 2, 20, 21, and 22, and torque calibration can be monitored via visual torque indicator. Read More

Portable Tools, Machinery & Machining Tools

Heavy-Duty 7 in. Portable Saw smoothly cuts wet/dry stone.

July 24, 2012

Model EDS 181, with 20 A motor and load speed of 4,300 rpm, cuts through hard stone surfaces, including granite, marble, terrazzo, and more. Cutting depth is adjustable without tools for precise cuts up to 2 1/3 in. deep, and built-in vacuum port enables dust-free operation. Along with support for connection to CS Unitec dust extraction systems, features include soft start, overcurrent cut-off, and motor overload protection with optical overload indicator. Read More

Machinery & Machining Tools

Pneumatic Circular Saw dry cuts steel and non-ferrous metal.

May 31, 2012

Equipped with 2 hp pneumatic motor operating at 90 psi using 60 cfm air, Model 5 1115 0020 dry cuts steel plate up to 3/8 in. thick, as well as non-ferrous metal, plastic, grating, composite, and corrugated materials. Portable 9 in. saw has overall cutting depth of 3 ¼ in. at 90° and 2 1/8 in. at 45°. Measuring .055 in. thick, Laser Beam Saw Blade is tungsten-carbide tipped and shock-resistant. Saw is suited for foundries, petrochemical, nuclear, marine, demolition, and fabrication industries. Read More

Portable Tools

Cotton Buffing Wheel produces high mirror finish on metals.

April 19, 2012

Intended for use with polishing compounds, pastes, and rouges, Cotton Buffing Wheel (CS 2410) produces bright, high mirror finish on stainless steel and other non-ferrous metals. Product is made of cotton yarn, measures 3 ½ in. dia x 4 in. wide, and is suited for flat, contoured, or irregular surfaces. This hollow-core wheel is designed for use with PTX Eco Smart Professional Surface Finishing Machine. Read More

Machinery & Machining Tools, Materials & Material Processing

Portable Mixing Station handles diverse construction compounds.

February 13, 2012

In addition to 16 A/1,800 W, 2-speed motor, HIPPO PMH 70F-RL features 2 mixing paddles designed with helix ribbon and side bars. Removable, cleanable liner and rimless bucket system facilitates mixing of multiple batches of construction compounds. Also included, Easy-roll Trolley and balanced Easy-tilt Cradle let one person mix, transport, and place up to 20 gal of material simultaneously. Casters move freely on level floors, and air-filled tires are available for rougher terrain. Read More

Portable Tools, Machinery & Machining Tools, Construction Equipment & Supplies

Wall Slotter cuts channels in concrete and masonry.

July 12, 2011

Powered by 20 A motor with 7,500 rpm no-load speed, EMF 150 uses 2 adjustable, parallel, 6 in. diamond blades to cut channels up to 1 13/16 in. wide x 1 ¾ in. deep in concrete and masonry. Tool accommodates needs of plumbing, HVAC, and electrical renovations by allowing pipe, conduit, and wire to be placed inside walls and floors. Closed hood optimizes air flow and facilitates fragment removal, while vacuum port keeps work environment safe and clean. Read More

Machinery & Machining Tools

Magnetic Drill makes up to 1 1/2 in. dia holes in tight areas.

June 14, 2011

Designed with horizontal motor mount, MAB 150 stands 7 in. tall and weighs 24 lb. It has 1 in. max drill depth with annular cutters in structural steel and other metals and is powered by 9.25 A, 110 V double-insulated motor with no-load speed of 400 rpm. Able to accept cutters with ¾ in. Weldon shank, portable drilling machine integrates automatic cooling/lubrication system, dual-coil magnet with holding strength of up to 2,640 lb, and left- or right-mounted advancing lever. Read More

Other Company News from
CS Unitec, Inc.