PLL Synthesizer targets FMCW radar systems.
Housed in 4 x 4 mm 24-lead LFCSP package, 6.1 GHz Model ADF4158 allows programmability and configurability without dependence on VCO linearity. Device features 25-bit modulus, which allows sub-hertz frequency resolution. Operating from 2.7-3.3 V supply, synthesizer offers ramp delay, ramp frequency readback, and ramp interruption. It is suitable for FMCW radar systems in automotive, aerospace,...
Read More »K-RAS Mutation Detection Kit is optimized for sensitivity.
Able to be applied to formalin-fixed paraffin-embedded tissues, SURVEYOR Scan K-RAS kit uses PCR amplification reaction and hybridization to form heteroduplex DNA molecules in samples with K-RAS mutation. Use of SURVEYOR Nuclease technology helps identify mutations in K-RAS gene associated with drug-resistant tumors. Kit detects mutations by enzymatic cleavage at mutation sites and identifies all...
Read More »
Low-Jitter Frequency Synthesizers facilitate timing design.
Intended for high-speed systems, MAX3671/MAX3673 utilize low-noise VCO and PLL architecture to generate high-frequency (312.5 MHz), low-jitter (0.3 psRMS) clock signals from 62.5 MHz reference-clock input. They offer 9 phase-aligned LVPECL outputs, operate from 3.3 V ±5%, and may be configured through three 4-level control inputs. While MAX3671 simultaneously generates 2 different...
Read More »
PLL/Synthesizer has low phase noise of -95 dBc/Hz at 10 kHz.
Housed in compact 0.582 x 0.8 x 0.15 in. SMD package, CPLL58-4240-4240 operates at 4,240 MHz with step size of 2,500 kHz and is programmed using standard 3 line interface (data, clock, and load enable). It integrates VCO and PLL in single package and needs only external frequency reference and supply voltages of 5 and 3 Vdc, respectively, for internal VCO and PLL. Second harmonic suppression is...
Read More »
An Introduction to Plastic Injection Molding
We developed this eBook with designers, engineers and purchasing specialists in mind. It is written to provide a basic understanding of plastic injection molding presses, processes and costs. Our goal is to make our customers more knowledgeable about what goes into making a plastic part.
Read More »
PLL/Synthesizer comes in 0.6 x 0.6 x 0.15 in. SMD package.
Operating at 3,475 MHz with typical step size of 2,500 kHz, CPLL66-3475-3475 features typical phase noise of -95 dBc/Hz at 10 kHz offset with minimum output power of 3 dBm. It is programmed using standard 3 line interface (data, clock and load enable) and features second harmonic suppression of -15 dBc typical. Integrating VCO and PLL in single package, unit needs only external frequency...
Read More »
PLL/Synthesizer operates from 3,900-4,300 MHz.
With typical step size of 2,500 KHz, model CPLL58-3900-4300 wraps VCO around PLL in 0.582 x 0.8 x 0.15 in. SMD package and requires only external frequency reference and supply voltages. It is programmed using standard 3-line interface - data, clock, and load enable - and exhibits typ phase noise of -95 dBc/Hz @ 10 kHz offset with min output power of 3 dBm. VCO voltage is 5 Vdc, PLL voltage is 3...
Read More »
PLL/Synthesizer operates from 1,800-1,860 MHz.
Housed in 0.582 x 0.8 x 0.15 in. SMD package, Model CPLL58-1800-1860 only requires external frequency reference and supply voltages for internal phase lock loop and voltage controlled oscillator. Typical phase noise is -103 dBc/Hz at 10 kHz offset with minimum output power of 3 dBm. VCO voltage is 5 Vdc and PLL voltage is 3 Vdc. Programmed using standard 3-line interface, device is suited for...
Read More »RFICs are rated to handle demanding applications.
Operating up to 4.4 GHz, ADF4150 PLL synthesizer is capable of Fractional-N or Integer-N operation and has -222 dBc/Hz phase-noise figure. Model ADL5601/ADL5602 broadband RF/IF gain blocks, operating from 50 MHz to 4 GHz, integrate internal bias circuitry and are fully ESD protected. With 400-2,700 MHz operating frequency range, ADL5604 broadband 1 W driver amp consumes 325 mA current. As...
Read More »
PLL Synthesizer combines VCO and PLL in one compact package.
Operating from 2,416-2,553 MHz with typical step size of 100 kHz, CPLL66-2416-2553 is housed in compact 0.6 x 0.6 x 0.15 in. SMD package. It needs only external frequency reference and supply voltages for internal PLL and VCO and is programmed using standard 3 line interface (data, clock, and load enable). Phase noise is -90 dBc/Hz at 10 kHz offset with minimum output power of 3 dBm, VCO voltage...
Read More »
PLL Synthesizer comes in 0.6 x 0.6 x 0.15 in. SMD package.
Featuring VCO wrapped around PLL in single package, CPLL66-1600-2200 operates from 1,600-2,200 MHz with typical step size of 1,000 kHz. It requires only external frequency reference and supply voltages for internal PLL and VCO, and is programmed using standard 3 line interface. Features include typical phase noise of -6 dBc/Hz at 10 kHz offset with minimum output power of +7 dBm, second harmonic...
Read More »
SEALTITE® Fittings and Cord Grips Offer Longer Lasting Protection
Anamet Electrical's 316 Stainless steel SEALTITE® fittings and UL-listed cord grips protect sensitive wiring components from fluids, corrosive contaminations, bumps, and abrasions with a steel core and liquid tight conduit jacket. Check out this video to learn more.
Read More »
