Hand-Held Transmitter measures CO2.
Available for Omniport 30 Hand-held Transmitter, CO2 Probe is based on NDIR dual wave length procedure and offers measurement range of 0–2,000/5,000/10,000 ppm. Omniport 30, suitable for ambient air monitoring or CO2 leak localization, offers continuous and single-point data logging with time stamp. Up to 3 measurements can be displayed simultaneously on TFT display. With internal memory,...
Read More »
Vibration Transmitter delivers continuous 4-20 mA output.
Featuring 2-wire loop-powered operation, Model VBT continuously detects vibration in system and monitors for unusual operating conditions and potential failure. Vibration is converted into analog signal at current output. Housed in 316 stainless steel, transmitter operates from -22 to 221-
Read More »Air Velocity Transmitter features built-in relay.
Featuring hot wire air velocity sensor design and choice of fixed mount or remote probe configurations, Model FMA900A measures air velocity up to 12,000 fpm with 2% full scale accuracy. Unit provides response time of 250 msec, 0-5 Vdc or 4-20 mA analog output, and 1 SPST relay contact closure with red LED indication. Equipped with adjustable high alarm set point, transmitter is suited for...
Read More »
Air Velocity Transmitters are virtually immune to drift.
Offering 8% accuracy, Series AVUB operates by measuring heat loss from sensing element in air-stream and calculating air velocity by reading local temperature of air on probe. Models are available in 3 ranges of 0-785 fpm, 0-1,575 fpm, and 0-3,150 fpm with 0-10 Vdc output. Offering 10 sec response time, Series AVUB is suited for wide range of HVAC measurement and control applications,...
Read More »
A Comprehensive Guide to E-Mobility and E-Aviation
This white paper provides a comprehensive guide to E-Mobility and E-Aviation.
Read More »
Vibration Transmitter turns accelerometer into monitoring sensor.
Installed with any industrial accelerometer, model 682A09 ICP-® In-Line Vibration Transmitter converts vibration signal to 4-20 mA velocity output that can be trended with various control room systems. Unit has 2-pin MIL connector input and 3-pin MIL connector output. Operating off of loop-power from PLC, DCS, or SCADA system, it accepts 100 mV/g analog signal, which can be run to central...
Read More »
Vibration Monitor is suited for oilfield pumps and motors.
Providing 4-20 mA output signal that is proportional to vibration amplitude, heavy-duty vibration transmitter Model 191 is 2-wire, loop powered sensor used to monitor oil and gas production pumps, compressors, fans, and motors. Powered by 12-24 Vdc source, output wire can be connected to any existing PLC, SCADA, or DCS system. Product is enclosed in rugged, NEMA 4 weatherproof case and is listed...
Read More »
Vibration Transmitter monitors conveyors.
Used with Model 1112 Vibration Monitor or other existing control system, Model 191 continuously monitors controlled vibration levels required to move bulk product at optimum process speeds. System automatically activates alarms and alerts operators to problem if vibration levels drop below or go above operator-selected preset limits. Capable of measuring up to 25 ips of vibration velocity,...
Read More »
Air Velocity Transmitter works in dirty environments.
Suited for monitoring air velocities in polluted environments, Series 641B employs protected, heated mass flow sensor from which users can remove dust and debris. Product offers operational versatility with its 8 field-selectable ranges from 0-250 fpm to 2,000 fpm.
Read More »Communication Module sends vibration data directly to PC.
DIN-rail mount, stand-alone iT Communication Module facilitates data acquisition and analysis for vibration transmitters by sending digital data directly to computer via RS232 serial port. Enabling users to monitor machine health from workstation without monitoring system, unit works in conjunction with VibeLink(TM) software and offers ability to trend data over time. Module continuously reads...
Read More »
Air Velocity Transmitter includes cable for remote mounting.
Series 641RM utilizes heated mass flow sensor, which allows for precise velocity measurements at various flow rates and temperatures. It offers 16 field-selectable ranges from 0-250 fpm to 15,000 fpm. Six foot cable connects sensing probe with electronic enclosure and allows enclosure to be mounted where it can readily be accessed. Longer cable lengths are available for ducts that are at very...
Read More »
DoorKing's 1601 Lane Barrier Provides a Higher Level of Traffic Control for Less
DoorKing is proud to introduce an easy add-on to its 1601 Barrier Gate Operator: The 1601 Traffic Lane Barrier. The barrier gate provides greater traffic control while eliminating the need for bollards or crash beams. Check out this video to learn more.
Read More »
