Impellers

Mixer and Agitator Propellers / Impellers

Impeller eliminates rag buildup.

Solving problem of rag buildup in municipal and industrial treatment, CLEAN EDGE Impeller remains free of fibrous debris while delivering performance equal to hydrofoil impeller. After 9 months of continuous operation, impeller exhibited no rag buildup on diameter, had same power draw as when installed, and caused no mechanical issues while delivering required mixing.

Read More »
Motorized Impellers offer capacities to 5,060 cfm.
Impellers

Motorized Impellers offer capacities to 5,060 cfm.

Offered in single or 3-phase voltages with dual frequency motors, Models TMK and TMK-H are equipped with BC airfoil wheel to provide quiet airflow. Units come in housed and non-housed models and are available with matching capacitors and inlet cones. Impellers are suited for variety of air-moving applications, including cooling of motor controls, electronics, power converter cabinets, and modular...

Read More »
Impellers

Impeller is optimized for surface aeration applications.

Suited for higher-RPM wastewater applications in industrial/municipal facilities combating solids, sludge, rag, and increased volume challenges, Talon(TM) provides maximum oxygen transfer rate while achieving efficient mixing and biological nutrient removal. Curved, large-diameter design promotes flow and oxygen transfer with standard aeration efficiency of up to 4.5 lb O2/hp-hr. Product can...

Read More »
Impellers

Chemineer Announces New XE-3 Impeller

Dayton, Ohio - Chemineer has again set a new benchmark in high efficiency agitator impeller technology with the XE-3 impeller. Chemineer impeller designs are the result of over five decades of research and applied application experience, resulting in the broadest range of durable and efficient impeller options for its agitators. The Chemineer XE-3 impeller is as much as 24% more efficient than...

Read More »
Hydrofoil Mixing Impeller optimizes fluid flow.
Impellers

Hydrofoil Mixing Impeller optimizes fluid flow.

Available in 3-210 in. dia sizes, HYFLOW 218 Impeller features hydrofoil-style, 4-blade design with tapered blades that have narrow, low-pitch section at tip where speed is fastest and wider, higher-pitch section nearer hub where it is slower. Curved blades resist bending under stresses from fluid forces and also reduce drag. Impeller, made from 316 stainless steel, titanium, inconel, nickel, and...

Read More »
Motorized Impeller suits space-limited applications.
Impellers

Motorized Impeller suits space-limited applications.

Equipped with electronically commutated external rotor motor, CEC Backward Curved Impeller provides capacities to 7,800 cfm. Both motor and impeller are located directly in air stream, where impeller acts as rotating heat sink, providing heat dissipation and motor cooling. Operating from 380-480 V, 50/60 Hz, 3-phase, aluminum impeller is speed controllable and suited for electronic cabinet...

Read More »
Axial Impellers incorporate airfoil blade design.
Impellers

Axial Impellers incorporate airfoil blade design.

Designed using computer-aided technology, ELTA Axial Impellers feature pressure cast aluminum hubs and adjustable pitch blades. Available in diameters from 12-79 in., they accommodate up to 18 blades and deliver airflows to 200,000 cfm. Typical OEM applications include general ventilation, cooling towers, heat exchangers, process cooling, radiator cooling, and bulk drying.

Read More »
Impeller mixes materials with high shear sensitivity.
Impellers

Impeller mixes materials with high shear sensitivity.

Sentinel(TM) Impeller features wide, large-diameter blades for high flow and uniform distribution of shear throughout mixing process. Fully welded and bolted designs are available with different coatings and surface finishes to meet mixing specifications. Clean-in-place impeller is suited for applications where fluid motion is required to suspend solids, dispense gas, or blend fluids in...

Read More »
Impeller mixes materials with high shear sensitivity.
Impellers

Impeller mixes materials with high shear sensitivity.

Available in fully-welded or bolted designs with different coatings and surface finishes, Sentinel(TM) Impeller uses blades that deliver uniform distribution of shear throughout mixing process. It is suited for applications where fluid motion is required to suspend solids, dispense gas, or blend fluids in high-flow, low-shear process. It also suits clean-in-place systems with no horizontal...

Read More »
Side-Entering Impeller utilizes hydrofoil design.
Impellers

Side-Entering Impeller utilizes hydrofoil design.

Constructed from 316 stainless steel, 317L stainless steel, Hastelloy C276, or titanium, Maxflo WSE employs hydrodynamic design to improve cavitation resistance. Bolted-blade design is available in 4-blade model or 6-blade model for shock-loaded applications. Applications include industries such as pulp and paper, flue-gas desulphurization, and petroleum blending and storage.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers