Cylindrical Grinding

Cylindrical Grinding

M&S Centerless Grinding Manufacturers Spool/Sleeve Actuators for Boeing Aircraft

Problem: Part match-fit and cylindricity requirements made vendors willing to accept the responsibility of holding print tolerances scarce. Material: 440C HT 58 RC min. Critical Dimensions: Match-fit clearance: hold match fit clearance spool/sleeve to .00005 . The resulting cylindricity on both spool and sleeve necessarily were near .000025". 4 Ra surface finish.Â-  Resolution: Match-fit of...

Read More »
Cylindrical Grinding

M&S Redesigns Blood Testing Instrument

Device re-design resulted in issues with the ability to manufacture the key part of the instrument. Existing vendor base would not attempt to manufacture. Material: Tungsten Critical Dimensions: .0070 x .87” long in the middle of the part Hold +.0000/-.0002” tolerance on diameter Hold +/-.001” tolerance on length of .007” 8 Ra surface finish max Resolution: A manufacturing process was...

Read More »
Cylindrical Grinding

M&S Centerless Grinding Manufacturers Missile Wing Pins

A Tier-1 defense contractor rejected parts from their primary vendor for a high-end precision pin used to affix fins onto missiles. The rejection of the pins caused a delay in shipment of missiles to The Persian Gulf, and left them with no source for the pins after the primary vendor lost approved status. The Tier-1 contractor needed to ship missiles within 2 weeks otherwise late delivery...

Read More »
Radius Internal Cylindrical Grinders handle large workpieces.
Cylindrical Grinding

Radius Internal Cylindrical Grinders handle large workpieces.

WithÂ- workhead on simultaneously swiveling B-axis, STUDER S121, S131, and S141 offer thermal stability, mechanical rigidity, and interpolation from -60° to +90°. Machines also have dressing spindle or fixed dresser on B-axis and measuring probe on grinding head. X and Z axes are in cross-slide arrangement or cross slide with model-dependent spindle/turret...

Read More »
Peristaltic Pump Vs. i-FILL® Technology
Sponsored

Peristaltic Pump Vs. i-FILL® Technology

Intellitech's advanced i-FILL® pumps are used by companies working in some of the world's most demanding sectors, delivering innovative, highly accurate and repeatable results, ensuring ultimate reliability and ease of use for all of our clients.

Read More »
Cylindrical Grinding

M&S Centerless Grinding Manufacturers Solar Energy Components

The tolerances for diameter size and roundness on the ID of a special tube made manufacturing costly and vendors difficult to find. Product acceptance was going through the roof, but the lack of an adequate supply of this key component caused delivery delays and increasing order backlog which jeopardized the entire project. Material: 304 SST tubing Critical Dimensions: OD – approximately .2500...

Read More »
Cylindrical Grinding

M&S Centerless Grinding Manufacturers Heart Valve Clip for Defective Heart Valves

The extremely small size of the part, critical to affixing a clip to a defective heart valve, resulted in manufacturing difficulties, and unacceptable inconsistencies in holding the required part tolerances. Critical Dimensions: Center Diameter size - .0191/.0190 OAL: .056 8 Ra surface finish .001" max inside corner radii Resolution: a manufacturing process was created that yielded 95% success...

Read More »
Cylindrical Grinding

M&S Centerless Grinding Manufacturers Missile Wing Pins for Tier 1 Defense Contractor

A Tier-1 defense contractor rejected parts from their primary vendor for a high-end precision pin used to affix fins onto missiles. The rejection of the pins caused a delay in shipment of missiles to The Persian Gulf, and left them with no source for the pins after the primary vendor lost approved status. The Tier-1 contractor needed to ship missiles within 2 weeks otherwise late delivery...

Read More »
Cylindrical Grinding

O.D./I.D. Grinding Capability for Large Parts Added at Straton Industries

Stratford, CT -- Straton Industries is proud to announce the installation of a Kellenberger 1000u I.D./O.D Grinder with a size capacity of 40 inches between centers with a 20 inch O.D. swing. This new grinder is an addition to our current in-house FAA repair offerings and will give Straton the ability to expand the scope of our repair of components for helicopter and fixed wing aircraft. The...

Read More »
CNC North, Inc. Unveils New Internal Grinding Machine
Cylindrical Grinding

CNC North, Inc. Unveils New Internal Grinding Machine

Contact: Jessica Boudreau, Sales & Marketing Coordinator 860-749-1780 Ext. 3014 jboudreau@cnc1.com Since their incorporation in 2005 CNC North, Inc (Springfield, VT) has specialized in supporting, remanufacturing and providing design enhancements for Bryant Grinder CNC machines. The products and engineering developed for the Bryant models have allowed expansion of precision dressing systems and...

Read More »
Jones & Shipman Shows "Productivity Boosting" Precision Grinding Machines With Benefits Of 'Easy Control' At IMTS08
Cylindrical Grinding

Jones & Shipman Shows "Productivity Boosting" Precision Grinding Machines With Benefits Of 'Easy Control' At IMTS08

PRESS INFORMATION FROM JONES & SHIPMAN AT IMTS08 (Booth B6760) Jones & Shipman - Holroyd, world leaders in the supply of high quality, precision cylindrical, surface, creepfeed, gear and rotor grinding machine systems, are exhibiting at IMTS08 three market-leading machines plus two full size wheelhead modules; a novel multi-wheel design from Jones & Shipman and a stylised concept dressing unit...

Read More »

All Topics