Motion Controller Board handles 4 axes simultaneously.
Miscellaneous Controls

Motion Controller Board handles 4 axes simultaneously.

Double size PC-MIP board can be used on CompactPCI, PCI, VME and embedded platforms with high speed PCI bus interfaces. Chipset supports steppers, sinusoidal commutation of brushless motors, and positioning and velocity control of brush servo motors. Any axis can be selected to be brush or brushless. Instruction set supports 130 commands plus selectable profiling modes including S-curve,...

Read More »
Motion Control Chip drives stepper motors.
Miscellaneous Controls

Motion Control Chip drives stepper motors.

2-axis PCD-4521 controls two-phase unipolar or bipolar stepper motors. Sequence logic for both full and half-step modes is built-in. It can output CW/CCW pulses or excitation signals directly to drive chips, provides independent control of each axis, and controls simultaneous start and stop of all axes. Features include linear or S-curve acceleration and deceleration and idling pulse output for...

Read More »
Sensing and Timing Relay is capable of dual timing.
Level Controllers

Sensing and Timing Relay is capable of dual timing.

Series ST Sensing and Timing relay is used for level sensing applications that need to detect 1 level of a liquid. Features include optional ON-DELAY, OFF-DELAY or SINGLE SHOT timing; 115 VAC input; transformer isolated sensing circuit; and voltage protected sensing input. Resistance sensing is rated at up to 10 Megohms. Additional features include sensing and output LED indicators, 10 AMP SPDT...

Read More »
Contouring Control fits cycle-controlled lathes.
Miscellaneous Controls

Contouring Control fits cycle-controlled lathes.

MANUALplus 4110 control program machines complex workpieces on lathes with one spindle, X and Z axes, C axis or positioning spindle, and driven tool. Supporting interactive lathe operation and G-code, it performs simple operations like manual lathe. For complex contours, graphical Interactive Contour Programming calculates missing coordinates or shows mathematically possible variants so user can...

Read More »
Control System optimizes engine performance.
Miscellaneous Controls

Control System optimizes engine performance.

Engenius ESM Engine System Manager, directed by Engine Control Unit (ECU) monitors speed, pressure, temperature and other engine conditions; controlling ignition timing, speed governing and stop/start functions. It also provides diagnostic help and fault logging when requested. System can be packaged to instantly communicate to Internet server, computer, phone or pager via satellite, cellular...

Read More »
Motion Control Chipsets synchronize multiple axes.
Miscellaneous Controls

Motion Control Chipsets synchronize multiple axes.

Navigator and Pilot chipsets control brushed dc servos, brushless dc servos, steppers, and microsteppers. Navigator handles 4 axes, while Pilot handles 1. Multi-chip synchronization allows more than 4 axes of motion to be coordinated between any combination of Navigator and Pilot chips. It also allows physically remote or distributed chips to be synchronized within microseconds so they can be...

Read More »
Mass Flow Controller also records and manipulates data.
Flow Controllers

Mass Flow Controller also records and manipulates data.

Series DMF can be programmed for functions such as flow set point, totalizer, stop totalizer, totalize from preset flow, stop and preset auto, and auto zero. It has two outputs to operate pumps, valves or other equipment, and can control high and low alarm limits through its RS485 interface. Flow ranges vary from 0-10 sccm to 0-100 L/min with accuracy of ±1% of full scale. Operating...

Read More »
CNC Retrofit Kit fits older boring mills.
Miscellaneous Controls

CNC Retrofit Kit fits older boring mills.

Vega MILM-B Mill PC-based CNC retrofit package helps shops rejuvenate older machines. CNC has handwheel, joystick, and pushbutton jog interfaces, manual tapping, programmable cycles, mirroring and scaling, color LCD display, 32-bit CPU, hard disk, floppy disk and CD ROM. Retrofit package includes on-site installation and operator training. System can interface with both ac and dc servo systems.

Read More »
Universal Process / Temperature Controllers

Process Control System combines "snap-together" modules.

Pre-configured with snap-together" pneumatic modules, the AirLINE system consists of a Burkert pneumatic basic module, Phoenix Contact inline electronic modules and high-performance 10 mm multi-way solenoid pilot valves. It permits pneumatic actuators and electrical I/O to be controlled from the same device, on the same "rail-mount" assembly, using fieldbus communications, including Profibus DP,...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics