Chlorination Controller suits water/wastewater applications.

Model 555 -¼ DIN Controller provides solution for various chlorination and de-chlorination processes. Front panel is rated NEMA 4X, menu prompts are in plain English, and alphanumeric display is readable in all light conditions. With isolated 4-20 mA or 0-20 mA outputs for control or retransmission to analog system, unit offers alarm trip outputs for flow rate, chlorine residual, dosage setting,...

Read More »

Mass Flow Controllers offer optional fieldbus interface.

Combined with integrated or close-coupled control valves, IP65-rated IN-FLOW Series measures and controls gas flow within range of 0.2 mln/min to 11,000 m-³n/h air-equivalent. Units are ATEX approved for use in Category 3, Zone 2 hazardous areas. Basic PC board contains all general functions including alarm, totalization, and diagnostic functions, as well as analog I/O signals and RS232...

Read More »

Motion Control Libraries and Drives suit PLC applications.

Able to embed Technosoft Drive/Motor Intelligence on PLC environment, TML_LIB_S7 and TML_LIB_CJ1 consist of high-level functions and function blocks that allow for control of Technosoft intelligent drives and motors based on MotionChip(TM) technology. Developers can communicate with drive/motor via any of its supported channels, send motion commands, get automatic or on-request drive/motor...

Read More »

Remote Power Controller features redundant dc inputs.

Offering dual 50 A power inputs, IP-based Model RPC-4850-8N allows network administrators to control power ON/OFF or BOOT to eight 48 Vdc circuits at up to 15 A per circuit. Internal diode-bridge allows unit to feed power to output circuits from either input source. Model RPC-4850-8N can be controlled via HTTP browser or Telnet, as well as through RS-232 command-line serial port for out-of-band...

Read More »

Temperature Control Unit helps optimize process control.

ProcessMate(TM) 6500 eliminates temperature fluctuations that can cause variations in shot size, viscosity, and pot life when dispensing solder pastes, adhesives, and other assembly fluids. Designed for use with air-powered benchtop dispensers and automated dispense valves, stand-alone unit maintains temperature control within ±0.1°C over 10°-40°C operating range for consistent fluid deposits...

Read More »

Motion Controller supports Ethernet communications.

Model RMC75E provides closed loop position, speed, and pressure/force control for hydraulic, pneumatic, and electric servo applications at rate of more than 1,000 times/sec. Ethernet interface can be used to download parameters and variables from master controller and to upload production information to factory information systems. Interface delivers speeds of 10/100 Mbps with full- or...

Read More »

Navigation Sensors help automate inventory tracking.

NavPax Sensor Units integrate 3-axis MEMS gyros, accelerometers, compass, signal processing, and GPS information to provide complete package for real-time, land-based vehicle tracking solutions. They are used as part of RFID-aided warehouse tracking system that tracks position of each forklift, unique cargo identification, and pick-up and put-down locations of inventory with accuracy to 99%.

Read More »

Microcontroller delivers voice-enabled solution.

General-purpose RSC-464 IC provides speech recognition, synthesis, and system control on one chip. Inside speech recognition SoC includes 16-bit ADC, DAC, digital filter unit, math unit, 4K RAM, 64K ROM, output amplification, timers, and comparators. Also able to be used as slave for speech recognition, voice biometrics, and speech and music playback, product implements FluentChip(TM) v2.0...

Read More »

Stroke Rate Controller provides flow metering.

Suited for V-Series Metering Pumps, Model V300 offers variable control of fluid flow from 0 4 l/min in forward and reverse direction. Adjustable in 0.1% increments, membrane switches can start and stop pump without re-adjustment of stroke rate settings. Stroke rate can be controlled electronically through interface, which accepts 4-20 mA, 0-5 Vdc, and 0-10 Vdc input signals. Electronics are...

Read More »

Microcontrollers are suited for consumer applications.

Comprised of 36 product configurations with various memory, peripheral, and packaging options, 8-bit 78K0/Lx2 family incorporates LCD driver/controller and in-application, self-programming flash memory. MCUs have 16 128 KB flash memory and up to 7 KB RAM, consume 2.5 mA power, and provide wake-up time of 5 -µsec from standby to full-speed operation. Peripherals, designed to provide safe...

Read More »
Precision Fabricating with Over 40 Years of Experience
Sponsored

Precision Fabricating with Over 40 Years of Experience

Quality Sheet Metal specializes in delivering precision, value, and customer service. With a client base that spans many diverse industries and a reputation for excellence that goes back over four decades, our clients know that we can provide the optimal combination of value and flexibility regardless of the challenge. See our video to learn what we can do for you. Through investments in state-of-the-art design, manufacturing, and quality control systems, Quality Sheet Metal remains focused on maintaining a high standard of quality, customer service, and competitive pricing. With an emphasis on customer satisfaction, Quality Sheet Metal is dedicated to establishing long-term partnerships, similar to the ones they currently have with their valued clients. If youre looking for a new partner with extensive capabilities in sheet metal fabricating and finishing, look no further.

Read More »

All Topics