Thermal Controls are suited for inductive applications.

Available with various leads attached at factory, Model J(C) Valstat(TM) Series thermal protectors feature fold-over case design and same or opposite end terminations. Model BR-B2D Valstat Series, with drawn metal or heat-resistant plastic case, features sealed design suitable for applications requiring vacuum impregnation process. Both automatic reset devices feature snap action, quick...

Read More »

Digital Keypad Controls provide stand-alone operation.

Designed to control independent doors and gates, Series 8112 is available for indoor and outdoor applications. All programming of keypads is accomplished from front panel with guidance provided from LEDs and sounder. Units feature up to 120 valid user codes with restriction for specific time access; activation of lights or cameras prompted via programming; and keypad interaction/feedback...

Read More »

Controller achieves high efficiency on low loads.

With advanced standby function and high-voltage start-up with 700 V capability, L6668 current-mode PWM controller includes programmable soft-start, slope compensation for stable operation at duty cycles greater then 50%, and protective output current limiting. PFC interface enables pre-regulator turn off when load level falls below threshold, saving typically 0.5-1 W of no-load power consumption.

Read More »

Battery Development Kit debugs smart batteries.

Based on ATmega406 single-chip smart battery AVR® device, ATAVRSB100 Development Board uses 3 support modules to simulate individual cell voltage, total cell stack voltage, and charge/discharge current. Flash-based ATmega406 integrates voltage regulator, autonomous battery protection, 99% accurate monitoring capabilities, FET control, and cell balancing FETs. Firmware supports SMBus V1.1...

Read More »

Thyristor features front-mounted, digital LED display.

Offered in 20, 30, 45, 80, and 100 A ratings, THV microprocessor-based SCR power controller features programming keys, 3 output modes, and base-up setting (output bias). Set values and input signals, checked and monitored via front display keys, can also be made with external setting unit such as variable resistor. Unit offers programmable phase control or zero-cross control and comes with...

Read More »
Current Loop Controller works with motorized potentiometers.

Current Loop Controller works with motorized potentiometers.

Able to automate existing systems, MR267 remotely controls motorized potentiometer and/or rotary cam switch via 4-20 mA current loop, 0-2.5 V input, or external potentiometer. User-specified potentiometers provide absolute positional feedback information or function as variable resistor in analog control or bridge circuit. Rotary limit switches are programmed, via cams, to electrically control...

Read More »

Safety Controllers are rated to SIL 3 functionality.

Featuring Integrated Architecture, GuardLogix Controllers use RSLogix 5000 programming software, which helps manage safety memory so users do not have to manually partition logic to isolate safety-related data. Safety memory can be read by standard logic and external devices such as HMIs. Controllers leverage Common Industrial Protocol Safety on DeviceNet for safety I/O connectivity, and...

Read More »

DC/DC Controller powers UltraSPARC® and SPARC® processors.

Offering 45 A single-chip solution, PolyPhase® synchronous step-down controller, Model LTC3819, features 4 integrated MOSFET drivers and on-board 5-bit digital interface. Core voltage is from 1.025-1.4125 V in 12.5 mV steps and core current ranges from 15-40 A. Housed in 10-pin MSOP package, device operates at up to 90% efficiency from input voltage of 4.5-36 V, and includes current foldback,...

Read More »

Analog Controller suits fixed-point gas monitoring.

Appropriate for industrial and non-industrial applications, 2-channel Model 820 accepts one or two 4-20 mA input signals from any gas transmitter and displays reading on LED display. In addition to local interface, controller can be part of larger digital network using ModBus RTU protocol. It includes 5 programmable analog relays for alarm and fault conditions, and when alarm conditions are...

Read More »
Controller enables X-by-Wire technology for vehicle networks.

Controller enables X-by-Wire technology for vehicle networks.

Delivering 10 Mbps over 2 channels, application-specific FlexRay(TM) MB88121 provides fault-tolerant, deterministic data transmission, suitable for engine control, braking, and steering subsystems. It can be connected directly to existing CPUs and complements standard automotive buses, including CAN and LIN. Internal speeds reach 80 MHz with 4, 5, 8, or 10 MHz external oscillator, or by external...

Read More »

All Topics