Motion Controller Board handles 4 axes simultaneously.
Double size PC-MIP board can be used on CompactPCI, PCI, VME and embedded platforms with high speed PCI bus interfaces. Chipset supports steppers, sinusoidal commutation of brushless motors, and positioning and velocity control of brush servo motors. Any axis can be selected to be brush or brushless. Instruction set supports 130 commands plus selectable profiling modes including S-curve,...
Read More »
Motion Control Chip drives stepper motors.
2-axis PCD-4521 controls two-phase unipolar or bipolar stepper motors. Sequence logic for both full and half-step modes is built-in. It can output CW/CCW pulses or excitation signals directly to drive chips, provides independent control of each axis, and controls simultaneous start and stop of all axes. Features include linear or S-curve acceleration and deceleration and idling pulse output for...
Read More »
Sensing and Timing Relay is capable of dual timing.
Series ST Sensing and Timing relay is used for level sensing applications that need to detect 1 level of a liquid. Features include optional ON-DELAY, OFF-DELAY or SINGLE SHOT timing; 115 VAC input; transformer isolated sensing circuit; and voltage protected sensing input. Resistance sensing is rated at up to 10 Megohms. Additional features include sensing and output LED indicators, 10 AMP SPDT...
Read More »
Sensing and Timing Relay is capable of dual timing.
Series ST Sensing and Timing relay is used for level sensing applications that need to detect 1 level of a liquid. Features include optional ON-DELAY, OFF-DELAY or SINGLE SHOT timing; 115 VAC input; transformer isolated sensing circuit; and voltage protected sensing input. Resistance sensing is rated at up to 10 Megohms. Additional features include sensing and output LED indicators, 10 AMP SPDT...
Read More »
Guide to FDA Approval & Compliance
Manufacturers must comply with FDA rules and regulations to ensure public health.
Read More »
Contouring Control fits cycle-controlled lathes.
MANUALplus 4110 control program machines complex workpieces on lathes with one spindle, X and Z axes, C axis or positioning spindle, and driven tool. Supporting interactive lathe operation and G-code, it performs simple operations like manual lathe. For complex contours, graphical Interactive Contour Programming calculates missing coordinates or shows mathematically possible variants so user can...
Read More »
Contouring Control fits cycle-controlled lathes.
MANUALplus 4110 control program machines complex workpieces on lathes with one spindle, X and Z axes, C axis or positioning spindle, and driven tool. Supporting interactive lathe operation and G-code, it performs simple operations like manual lathe. For complex contours, graphical Interactive Contour Programming calculates missing coordinates or shows mathematically possible variants so user can...
Read More »
Control System optimizes engine performance.
Engenius ESM Engine System Manager, directed by Engine Control Unit (ECU) monitors speed, pressure, temperature and other engine conditions; controlling ignition timing, speed governing and stop/start functions. It also provides diagnostic help and fault logging when requested. System can be packaged to instantly communicate to Internet server, computer, phone or pager via satellite, cellular...
Read More »
Control System optimizes engine performance.
Engenius ESM Engine System Manager, directed by Engine Control Unit (ECU) monitors speed, pressure, temperature and other engine conditions; controlling ignition timing, speed governing and stop/start functions. It also provides diagnostic help and fault logging when requested. System can be packaged to instantly communicate to Internet server, computer, phone or pager via satellite, cellular...
Read More »
Motion Control Chipsets synchronize multiple axes.
Navigator and Pilot chipsets control brushed dc servos, brushless dc servos, steppers, and microsteppers. Navigator handles 4 axes, while Pilot handles 1. Multi-chip synchronization allows more than 4 axes of motion to be coordinated between any combination of Navigator and Pilot chips. It also allows physically remote or distributed chips to be synchronized within microseconds so they can be...
Read More »
Motion Control Chipsets synchronize multiple axes.
Navigator and Pilot chipsets control brushed dc servos, brushless dc servos, steppers, and microsteppers. Navigator handles 4 axes, while Pilot handles 1. Multi-chip synchronization allows more than 4 axes of motion to be coordinated between any combination of Navigator and Pilot chips. It also allows physically remote or distributed chips to be synchronized within microseconds so they can be...
Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.
Read More »
