OCXO offers phase noise performance down to -172 dBc/Hz.

Press Release Summary:



Available at any frequency from 80–130 MHz, IQOV-200 Series delivers phase noise performance of -172 dBc/Hz at 100 kHz offset and -160 dBc/Hz at 1 kHz offset based on nominal oscillating frequency of 100 MHz. Oven Controlled Crystal Oscillator nominally operates from 12 V power supply and consumes 1 W of power at steady state. Drive capability is quoted at +6 dBm into 50 Ω. Housed in 36 x 27 mm IEC C008 Euro package, OCXO operates from -20 to 60°C with initial frequency stability of ±50 ppb.



Original Press Release:



New High Frequency OCXO from IQD Delivers Class Leading Phase Noise Performance Down to -172dBc/Hz



Launching at IMS 2013, IQD’s new IQOV-200 series Oven Controlled Crystal Oscillator (OCXO) has been designed from the ground up to optimize low phase noise performance. Phase noise is caused primarily by semiconductor thermal noise but noisy resistors, capacitors and inductors can all have an effect, as can poor signal transfer paths due to circuit layout and design. Good oscillator design consideration allow the IQOV-200 series to deliver phase noise performance of -172dBc/Hz at 100kHz offset and -160dBc/Hz at 1kHz offset based on a nominal oscillating frequency of 100MHz.



Available at any frequency in the range 80MHz to 130MHz, the new model is initially housed in an industry standard 36 x 27mm IEC C008 Euro package although other package styles including surface mount variants can be considered to suit specific customer applications. The oscillator nominally operates from a 12 Volt power supply and consumes just 1 Watt of power at steady state, incorporating a very high level of internal voltage regulation so proving somewhat immune to external voltage variations. Drive capability is quoted at +6dBm into 50 Ohms.



Operating over a standard temperature range of -20 to 60 degrees C with an initial frequency stability of ±50ppb (parts per billion), other temperature ranges and stabilities can be considered as required. The key component within any quartz oscillator is the quartz crystal and the IQOV-200 series’ long term aging rates are particularly low due to the very high quality and processing of the quartz crystal. IQD’s German based high specification division IQD FOQ GmbH where the new model was designed, has the critical advantage of close integration between the single site in-house crystal and oscillator design and manufacturing departments. The new model incorporates a SC-cut (Stress Compensated) HC43 cold welded crystal as exhaustive research has shown that this style of package offers much less stress on the crystal than the more commonly used multiple mounting point systems. This has a direct effect in improving the oscillator’s close-in phase noise. The actual drive circuitry has its most direct influence on the far-out phase noise performance. Inevitably both aspects are somewhat interactive so a fine engineering balance has to be struck.



There are many potential applications for this high specification OCXO including ground and airborne radar equipment (both military and commercial); military digital communications systems; satellite communications such as ‘Very Small Aperture Terminal (VSAT) – for data transfer from a remote ground terminals to high orbiting satellite such as the Inmarsat system with minimal distortion; high performance Global Positioning Systems (GPS); phase locked microwave signal sources and frequency synthesizers and signal generators. Phase noise or phase jitter is of particular importance because it reduces the signal quality and hence increases the bit error rate of a communications system. Indeed, in complex communications systems the amplitude noise caused by high signal levels is often of less importance than the phase noise content. While phase noise is an unwanted addition to all signals, its presence must be accounted for in many applications. Phase noise is an important aspect of synthesizer design as a further example and levels of phase noise must therefore be considered at the earliest design stages.



Test equipment is another key application for the IQOV-200 series. A very clean signal source is required for the reference source since any fluctuations will manifest themselves as side bands on the main signal and since the test equipment is the reference then in simplistic terms you will not actually measure what you think you are measuring.



Pricing will vary widely depending upon specific customer specifications but is likely to be in the range of $250 to $1000.



Further details will be available at IQD’s booth no. 137 at IMS 2013.



Backed by a pedigree that has been developed over nearly 40 years, IQD Frequency Products is a recognized market leader in the frequency control market. We have operations in America, Asia and Europe including our specialist high performance product manufacturing division, IQD FOQ GmbH in Germany. With active customers in over 60 countries, IQD offer one of the most comprehensive frequency product ranges available, from low cost commercial grade product to that used in high reliability military and professional grade applications. Our range includes Quartz Crystals, Crystal Oscillators, Silicon/MEMS Oscillators,  Fast Make Oscillators, VCXOs, TCXOs, OCXOs, Automotive Crystals & Oscillators to AEC-Q200 & TS16949 release, Crystal Filters, Real Time Clock, SAW Filters and VCOs & Synthesizers.



Quality and customer service are the cornerstones of our success and we are absolutely focused on consistently meeting and exceeding customer expectations. We take a partnership approach to working with our customers. Our experienced multilingual Sales and Application Support teams guide customers from design stage through to full production.



IQD’s products are specified by leading manufacturers in the aerospace, automotive, communications, computing, consumer, industrial, medical and military industries throughout the world. We work with several premier chip-set designers on a variety of key projects and hold approvals on a number of products including high specification oscillators. Our full range of products is available direct from all of our offices or via our extensive worldwide distribution and representative network. Full contact details are available on our website at www.iqdfrequencyproducts.com.



Further information:

Maria Shoteh

IQD Frequency Products Inc

T: +1 408.273.4530

E: maria.shoteh@iqdfrequencyproducts.com

W: www.iqdfrequencyproducts.com



Join us on:     facebook  -    Twitter  -    LinkedIn   Google Plus

More from Electronic Components & Devices

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers