Kason Corp.
67-71 East Willow St.
Millburn, NJ 07041
Share:
CGM 750 Cone Mill Uses Vacuum Conveying System for Feeding
Kason’s 750 mm diameter CGM 750 Cone Mill is designed for grinding fatty, heat sensitive, sticky, moist or fragile materials. Unit delivers particle size distribution from 125 to 250 microns and features swing-down conical discharge chute for lowering 250 lb cone housing. This mill is constructed of 304 or 316 stainless steel with fully interlocked moving components with time-delay function....
Read More »
CGM 750 Cone Mill Uses Vacuum Conveying System for Feeding
Kason’s 750 mm diameter CGM 750 Cone Mill is designed for grinding fatty, heat sensitive, sticky, moist or fragile materials. Unit delivers particle size distribution from 125 to 250 microns and features swing-down conical discharge chute for lowering 250 lb cone housing. This mill is constructed of 304 or 316 stainless steel with fully interlocked moving components with time-delay function....
Read More »
Centrifugal Sifter achieves rates to 100 tons/hour.
On continuous basis, Model K1350C- removes oversize foreign matter and agglomerates from on-size material at rates to 100 tons/hr. System features cantilevered 3-bearing shaft design with bearings at motor end of shaft and on exterior of discharge end cover, providing maximum support for heavy loads. Forward and lift access door on gas struts optimizes interior access. Sifter is available in...
Read More »
Centrifugal Sifter achieves rates to 100 tons/hour.
On continuous basis, Model K1350CÃ- removes oversize foreign matter and agglomerates from on-size material at rates to 100 tons/hr. System features cantilevered 3-bearing shaft design with bearings at motor end of shaft and on exterior of discharge end cover, providing maximum support for heavy loads. Forward and lift access door on gas struts optimizes interior access. Sifter is available in...
Read More »
Sanitary Cone Mill processes sticky, moist, fragile materials.
Constructed of 304 or 316 stainless steel to sanitary standards, Kek-Gardner Model CM540 Sanitary Cone Mill delivers gentle, low-energy size reduction while achieving even particle distribution with minimal fines. This smooth, moderate action alleviates such problems as product build-up, dust, and heat generation. Conical screens are offered with apertures from 150 micron, for fine/dry...
Read More »
Sanitary Cone Mill processes sticky, moist, fragile materials.
Constructed of 304 or 316 stainless steel to sanitary standards, Kek-Gardner Model CM540 Sanitary Cone Mill delivers gentle, low-energy size reduction while achieving even particle distribution with minimal fines. This smooth, moderate action alleviates such problems as product build-up, dust, and heat generation. Conical screens are offered with apertures from 150 micron, for fine/dry...
Read More »
Fluid Bed Agglomerators range from 18-84 in. in diameter.
Encompassing batch and continuous applications, VIBRO-BED™ employs spraying system that introduces moisture to powdered material as it is fluidized and dried, forming agglomerates on controlled basis. Fluid bed chamber, equipped with imbalanced weight gyratory motors and mounted on spring suspension, vibrates as column of heated air flows upward through fine-mesh screen, causing particles to...
Read More »
Fluid Bed Agglomerators range from 18-84 in. in diameter.
Encompassing batch and continuous applications, VIBRO-BED™ employs spraying system that introduces moisture to powdered material as it is fluidized and dried, forming agglomerates on controlled basis. Fluid bed chamber, equipped with imbalanced weight gyratory motors and mounted on spring suspension, vibrates as column of heated air flows upward through fine-mesh screen, causing particles to...
Read More »Round Screen Replacements increase accuracy, reliability, uptime.
Available for round vibratory screeners of any make and model, K-Series lets users increase screening accuracy and reliability while decreasing downtime. There are 5 types of screens, offered in 18–100 in. dia that can be weld- or epoxy-mounted with or without center holes. Meshes range from 2 in. to 500 mesh in 304 stainless, 316 corrosion-resistant stainless, magnetic 430 stainless, exotic...
Read More »Round Screen Replacements increase accuracy, reliability, uptime.
Available for round vibratory screeners of any make and model, K-Series lets users increase screening accuracy and reliability while decreasing downtime. There are 5 types of screens, offered in 18–100 in. dia that can be weld- or epoxy-mounted with or without center holes. Meshes range from 2 in. to 500 mesh in 304 stainless, 316 corrosion-resistant stainless, magnetic 430 stainless, exotic...
Read More »