Maxta

100 Mathilda Place, #170
Sunnyvale, CA 94086

Tool Kit supplies handy array of live-circuit tools.

MRO Super Kit Plus contains dielectric safety tools for work on energized circuits up to 1,000 Vac and 1,500 Vdc. All tools are double-insulated and manufactured to ASTM F-1505.94 standard. When outer orange insulation layer has worn, inner yellow layer shows through, serving as early warning to remove tool from service. Kit includes screwdrivers, pliers, nutdrivers, sockets, box end wrenches,...

Controls & Controllers

Ethernet Switches handle 8 or 9 channels.

Single-chip, 8-port KS8997 and 9-port KS8999 switch ICs can be used in 10/100 Ethernet DSL, cable, and wireless routers and gateway networks. Both support DiffServ and IEEE 802.lp to prioritize different classes of voice, video and data traffic. With port-based VLAN, devices allow user to establish VLAN groups for security between groups and applications. Devices handle up to 9 MACs, 8 PHYs,...

Sensors, Monitors & Transducers

Liquid Level Meter provides specific gravity compensation.

Microprocessor-based Model LE100 has built-in back pressure sensor capable of measuring levels up to 1000mm. Front panel mylar display features 2 digital readings for actual level and set value, 8 output LED indication, and 4 push buttons for setting unit. Built-in linearizer compensates for variations in tank shapes. LE100 provides sampling time of 0.2 sec with +/- 0.3% repeatability. It can...

Agricultural & Farming Products

I/O Controller uses 20-pin Molex connector.

IOC-7007 I/O controller includes 10/100 Base-T Ethernet port and input and output options. It can accept up to 7 I/O IOM modules, available with TTL inputs, optoisolated inputs, optoisolated outputs, high power outputs, dry contact relays, analog inputs, or analog outputs. IOC-7007 incorporates 32-bit microcomputer with memory and multitasking. Box-level version accepts 90-260 VAC or 20-60 VDC,...

Fluid & Gas Flow Equipment

Desiccant Air Dryer works without heat.

Optima LX Series heatless desiccant compressed air dryer provides ultra dry air required for critical compressed air applications. It has maintenance free shuttle valves, high efficiency coalescing prefilter, and particulate removal afterfilter. Non-lubricated switching valve and two solenoid-operated purge valves replaces up to 13 separate valves used in company's other designs. Dryers are...

Sensors, Monitors & Transducers

Light Scattering Detector is for micro and capillary HPLC.

PL-ELS 1000Ã-µ microbore evaporative light scattering detector provides baseline stability for HPLC separations requiring gradient elution. Detector operates with eluent flow rates from 1 to 500 Ã-µl/min, detects all non-volatile solutes, and does not require UV chromophore. It can be used as standalone detector for separations using capillaries down to 300 Ã-µm ID, or can be used as...

Electronic Components & Devices

Disconnect Switches can be used in hazardous areas.

MD2DS Series factory-sealed disconnect switches are engineered to meet NEC and IEC performance standards. Fused and non-fused 600VAC models are offered in 30, 60, and 100 Amp designs. MD2DS switches incorporate stainless steel bolts and hardware, copper-free aluminum enclosure with epoxy powder finish, and insulated, dual-color operating handle that indicates when switch is energized. Handles can...

Communication Systems & Equipment

Horizontal Machining Centers are FMS system-ready.

HU50-5AX tilting trunnion table type machine accommodates part dia up to 27 in. and weights up to 1430 lbs. 50 taper spindles are available with up to 12,000, or 15,000 rpm and 40 taper up to 20,000 rpm. HU40T features max part dia of 20 in. 40 taper spindles are available with up to 12,000, 15,000, 20,000 rpm or 30 taper up to 40,000 rpm. Both machines hold 0.00012 in. true position through all...

End Mills have long reach.

Solid carbide GLR series (square end) and BLR series (ball end) end mills are available in 2 and 4 flute configurations. Both are center cutting with 300 helix and have 0.020 in. reduced neck dia for extra clearance required in long reach milling applications. End mills are available in dia from 3/16 to 1 in. in 9 sizes. Shank dia tolerance is -0.0001 to -0.0003 in. T.I.R. maximum is 0.0005 in....

Recording Sofware runs on PocketPC.

PocketDataSheet software package turns PocketPC into hand-held data recorder and digitizer. Users specify names, units and order of instruments to be read, plus out-of-bounds values and help files. Program provides multiple screens to allow for password entry, time stamp, individual data input, notes and maintenance calls. Each data entry is checked for abnormal values and, if appropriate,...