Granta Design Ltd.
Cambridge CB1 7EG GBR
Share:
Electronic Thermocutter weighs 11--½ oz.
With transformer replaced by high-tech electronics, AZTC-20 electronic thermocutter cuts synthetic fabrics, plastic tubes, fiber optics, foam and similar materials that tend to crimp, serrate or unravel when cold cutters are used. Temperature in unit is controlled from zero to 1050Ã-ºF, while electrical current control switch allows selection of large blades. Cutting foot accessory lifts...
Read More »
Axial Exhaust Fans are suitable for roof or wall mounting.
Available in sizes ranging from 10-18 in., RMD axial exhaust fans feature totally enclosed and permanently lubricated ball bearing motor. Ideal for areas with little or no duct work, units come with axial impellers constructed with die formed blades riveted to steel hub. With 110Ã-
Read More »Connector comes with 150 A current rating.
Suited for telecom power supply and power distribution applications, CROWN CLIP JUNIOR connector mates directly to power bus bar at less than 30Ã-
Read More »Dual Rated Enclosures are NEMA 4 weatherproof classified.
NEMA 9 dust ignition proof, dual rated enclosures encompass Model RS-D and Model RSB-D pull cord or cable operated stop control, Model TA-D belt alignment control, Model DB-100D belt rip detector, Model PCL/R/D-D pull cord, Model CR-D level control and plugged chute detector, and Model FS-D dry bulk material flow control series. UL listed and CSA certified units can be placed outdoors in...
Read More »Motion Card does not require host bus connection.
Measuring up to 16 x 10.7 cm, Prodigy Stand-Alone card downloads motion control programs with on-board C-Motion Engine for onboard execution, off-loading, or eliminating PC host. It is available with horizontal connectors or optional vertical connectors for stackable configurations which aids in choosing mounting locations and cable options. Product supports Ethernet communications with UDP and...
Read More »
Exhaust Fans can automatically turn on or off as required.
With ability to adjust fan speed continually to produce optimal flow, Strobic AirÃ-® Smart Fan(TM) suits safety critical applications such as laboratory fume hood exhaust and ventilation for specialized care environments. Product uses combination of sensors and controls to determine flow required for safe operation. Fans can sense fan failure and turn on stand by fan to maintain safe exhaust...
Read More »Development Kit helps to design and test 2 mm PCB connectors.
Shielded Controlled Impedance (SCI) Cable Assembly Development Kit helps engineers assess, test, and design appropriate high performance 2 mm SCI cable-to-board solution for their application. Development kit can be used to verify signal integrity, impedance matching, and crosstalk performance for designs that require up to 1 Gbps single-ended performance per signal line or 5 Gbps differential...
Read More »
Insulation and Continuity Testers have CATIII 600 V rating.
MIT200 Series insulation and continuity testers offer live circuit protection, fit easily into pocket, and are tough enough to withstand demanding industrial applications. MIT220 model offers insulation testing at 250 and 500 V, while MIT230 allows testing at 250, 500, and 1,000 V. Both feature 1,000 MW insulation testing at all supported voltages, 200 mA continuity test current and fast-response...
Read More »
Pocket-Sized Infrared Thermometer features USB interface.
Available with built-in memory for storing up to 100 temperatures, PyroPen U thermometer measures temperatures from -20 to +500Ã-
Read More »Right Angled D-Sub Connectors feature press-fit termination.
Available with assembly height of 7.3 mm, right-angled D-sub connector can be screwed to PCB with M3 or 4 #40 UNC threads after press fitting to provide more secure attachment. Connectors are available with 9, 12, 25 or 37 pins; male contacts are gold-plated, while female contacts are tin-plated. Compliant with IEC 807-3 and DIN 41652, connectors also feature integrated locking jack screws that...
Read More »