AdTech Ceramics Company
Chattanooga, TN 37405
Jun 19, 2007 Blending injection molding with HTCC alumina systems, capabilities include metallization with refractory metal or platinum conductors, nickel and gold plating as required, and ceramic material options. Metal components may be attached with high-temperature braze, and complex 3D shapes are possible without additional machining. Tooling turnaround promotes feasibility for prototype and small production runs of complex shapes.

Parker Hannifin Corp., Cylinder Division
Des Plaines, IL 60016 3198
Jun 18, 2007 Designed for clamping, load holding, or E-stop applications, Series 3MA and 4MA cylinders hold loads in static condition while air pressure is removed from system. Available in 7 bore sizes ranging from 1.125-5.00 in., low friction 3MA cylinders have maximum operating air pressure of 250 psi and operating temperature range of -10 to +165°F. Intended for customization, 4MA units feature -50 to +250°F temperature range, standard and oversize rods, and externally removable rod gland.

Zarlink Semiconductor
Ontario K2K 3H4  Canada
Jun 05, 2007 With modular WPX power management process, designs can be developed using minimal layers in applications such as DC-DC power bricks, mobile telephone battery power management, linear and switching regulators, and other linear power management applications. This low-capacitance, linear bipolar process features lateral PNP transistors, poly resistors, and nitride capacitors. Its 2-layer metal allows low-current circuits to be built with high packing densities.

Birchwood Casey
Eden Prairie, MN 55344 2138
May 30, 2007 In addition to creating protective barrier against corrosion, TRU TEMP® black oxide finishing process offers break-in lubricity and anti-galling protection. Finish complies with MIL-DTL-13924, Class 1 and withstands 100-300 hr salt spray. Suited for valves, pumps, couplings, packer glands, and associated equipment, process forms non-dimensional, deep black finish; is pollutant-free; and operates at 200°F. Total process time is 25 min.

Topco, Inc.
Elizabeth, NJ 07206
May 25, 2007 Deep Drawn Stampings can be manufactured from materials such as aluminum, steel, and brass, as well as other metals. Available tooling library will result in minimal initial tooling investment to develop new parts. Machinery also can perform small metal stamping parts such as: spring metal stampings, clip metal stampings, and cup metal stampings, produced with progressive dies, compound dies, or single operation dies. All parts are made to meet individual requirements.

austriamicrosystems AG
Premstatten   Austria
May 18, 2007 Utilizing 0.35 µm SiGe-BiCMOS process technology, 2.7, 3.3, 5, and 12 V devices can be integrated on single chip without any process changes. Devices rated at 12 V enable high frequency operations, such as NPNs with BVceo of 14 V and ft/fmax of 15/32 GHz and RF-PLMDOS with BVds of 18 V and ft/fmax of 11/28 GHz. SiGe-BiCMOS technology is suited for users developing products such as line drivers for xDSL modems, Ethernet applications, and power amplifiers.

Dow Corning Corp.
Midland, MI 48686 0994
May 18, 2007 Designed to require minimal cycle times to accommodate high-speed manufacturers, Silastic® LC-70-2004 liquid silicone rubber (LSR) has 70 shore hardness and is formulated for optimal mechanical properties and clarity. Material meets FDA21 CFR 177.2600 and BfR, XV food contact standards and is suited for precision-production of complex parts. Applied through automated injection, material offers smooth release from mold to help produce complex parts design with optimal consistency.

Fivestar Die Casting Inc.
Moundsview, MN 55421
May 15, 2007 Providing custom high-pressure/high integrity aluminum and zinc die castings with full machining and component assembly capabilities, Die Casting manufacturing service delivers line-ready assemblies to meet just-in-time requirements. Press capabilities in zinc and aluminum range to 400 and 800 tons clamp force, respectively, while high integrity processes include squeeze casting and semi-liquid casting. Service targets hydraulic, engine, and electrical end product applications.

Accura Technics LLC
Keene, NH 03431
Apr 17, 2007 MicroTol(TM) features configurable work area that is totally enclosed for coolant containment. Standard X-axis travel is 8 in., while standard Z-axis travel is 4 in. Work area consists of a hydraulic chuck supported by Accura(TM)'s hydrostatic work spindle and hydrostatic bearings that provide added damping. The 20,000 rpm air bearing wheel spindle is rigidly mounted to machine base on micro-adjustable column, and grinding is performed with metal bond diamond wheel.

Optotherm, Inc.
Sewickley, PA 15143
Apr 02, 2007 PCB Test Arm Probe provides probing of surface mount devices (SMDs), and connects test instruments to variety of SMDs including PLCC, SOIC, QFP, and VIAS or test point holes. With length of 8.33 in., height of 2.92 in., and base length of 2.53 in., it includes spring loaded tip, rotatable head, and fine vertical adjustment knob, and is available in 3 and 10 A models. Connection post supports single or multiple test leads.

MH&W International Corporation
Mahwah, NJ 07430
Mar 19, 2007 Keratherm® 86/77 provides electrically conductive bonding sites on flexible material that attaches to non-linear, heat spreading structures. Flexible thermal circuit consists of thin layer of etchable copper bonded to thermally conductive silicone film, and can be applied to curved and irregular surfaces with peel-and-stick attachment. Secured with thermally conductive adhesive, conformable material ranges from 0.16-0.326 mm thick.

APM-Hexseal Corp.
Englewood, NJ 07631
Mar 14, 2007 Suitable for just about any electrical/electronic component including printed circuit boards, Low-Pressure Injection Process uses molten thermoplastic polyamide hotmelt for overmolding. In many production situations, it offers alternative to epoxy or urethane fillers or conformal coating and is suitable for temperature-sensitive and complex shaped parts that need environmental protection against dust, oil, chemicals, and jostling.

Vishay Intertechnology, Inc.
Malvern, PA 19355 2143
Feb 22, 2007 To meet custom requirements, Quick-Net(TM) allows designers to specify package format, schematic pin-out, and electrical performance. Resistance ranges are package specific and range from 100W to 100 kW for most formats, with values up to 1 MW available in single in-line formats. Performance limits include ratio tolerances down to ±0.01%, absolute tolerances of ±0.1%, TCR tracking of ±5 ppm/°C at temperature range of 55-125°C, and max wattage of 25 mW/element.

David Rigby Associates
Stockport   United Kingdom
Feb 07, 2007 DRATEFS forecasting reports track, by volume, value, year, and country, worldwide final consumption of textile products and components they contain, such as fibers, yarns, fabrics, chemicals, and dyestuffs. Reports feature driver-based forecasting model and database with 281 distinct products analyzed into textile components and characteristics. Forecasts can be generated up to 10 yr ahead for up to 210 different countries or regions.

Trimble Navigation Limited
Sunnyvale, CA 94085-3913
Jan 29, 2007 Designed for agricultural applications, AgGPS® EZ-Guide® 500 provides GPS-based guidance for steering tractors, sprayers, fertilizer applicators, air seeders, and tillage tools that require consistent pass-to-pass accuracy. Color, 7 in. LCD shows plan and perspective views, which let user see covered area in real-time. Built-in lightbar has guidance LED array that is visible even in direct sun, and data logging function lets users record day's work and transfer it to PC.

80/20, Inc.
Columbia City, IN 46725
Jan 23, 2007 T-slotted profiles are designed for machine frames, office furniture, machine guards/ enclosures, motion picture fixtures/lighting, material handling equipment, and prototype equipment. Metric profiles are available in 4 or 6 m stock lengths, or cut to desired length with clear anodized finish.

ADAMS Magnetic Products, Co.
Elmhurst, IL 60126
Jan 18, 2007 Assemblies made with Neodymium (Neo) magnets are available in 3 main styles: round base, channel, and sandwich. Each is constructed with magnet encased in plated or powder-coated steel cups, channels, or plates. Coatings are available for outdoor use, and rubber boots provide scratch resistance. Use of Neo magnets increases capacity of 30 lb assembly to 100 lb while staying within given size and shape requirements.

Motorola, Inc.
Schaumburg, IL 60196 4041
Jan 10, 2007 Comprised of 6 models, Motorola DCH Series delivers surround sound audio as well as SD and HD video that can be scaled to 720p or 1080i resolution. Products include hard drive for time- and place-shifting capabilities as well as media storage. Enabling on-demand and interactive digital cable programming, series provides connectivity via High-Definition Multimedia Interface®, optical and coaxial digital audio outputs, and IEEE 1394a, USB, and Ethernet interfaces.

Cardinal Health
Winchester, KY 40391
Dec 19, 2006 ReadyScan(TM) provides hospitals with pharmaceuticals in unit-of-use packages, complete with bar codes that help clinicians verify medications at bedside. Service repackages oral solid medications that are not available in unit-dose package. Medications are handled in Cardinal Health facility that follows current Good Manufacturing Practices (cGMP) under Food and Drug Administration guidelines.

Fivestar Die Casting Inc.
Moundsview, MN 55421
Nov 28, 2006 Providing custom-manufactured die cast parts with high strength and pressure tightness, Die Casting Services include conventional high pressure die casting, squeeze casting, and semi-liquid process casting. Company's Buhler 630 SC High Pressure Die Casting machine is fully automated with Thermtronix melting/holding furnace, Rimrock autoladle and die spray units, Sterlco die thermal control unit, and ABB 5-axis robot for part extraction/trim press loading.