Pickering Interfaces Inc
GRANTS PASS, OR 97526
Mar 06, 2008 Offered as 4- or 8-slot BRIC module, 40-569 integrates 16-wire analog bus with BUS Matrix cards and Resource Distributor cards. Scalable design permits inclusion of up to 2 off Resource Distributor subsystems and 6 off Bus Matrix subsystems. Also available, 40-618 Source Switching Module implements switching functions defined in Appendix D of ARINC specification. Each module can be supported in any 3U PXI chassis or Pickering Interfaces LXI Modular Switching Chassis.

O.BERK Co.
Union, NJ 07083
Feb 26, 2008 Carafe Bottles, both with 28-400 finishes, are suited for water, juice, tea, edible oils, and other beverage products. Lightweight bottles are available with custom colors, labeling, and silk-screen printing. Ergonomic design of these bottles near neck makes them easy to pour with maximum room for strong label presence.

Interstate Specialty Products
Sutton, MA 01590
Feb 19, 2008 Performed in clean-practice, positive-pressure facility, Digital Die-Less Cutting Service permits multiple on-the-fly part modifications for rapid prototyping. It offers non-metallic parts with intricate shapes, including narrow cross sections and close hole spacing, in sizes from less than 1 in. square to 60 x 120 in. with ±0.005 in. tolerances. End-user sends/specifies materials to be cut; submits DXF, PDF, or other drawing file; and receives parts for approval within 2-3 days (typ).

Birchwood Casey
Eden Prairie, MN 55344 2138
Jan 30, 2008 TRU TEMP® CNC non-polluting process uses integrated programmable hoist and tank to automatically process iron and steel components with black oxide finish. Operating as self-controlled unit, repeatable solution employs digital Allen Bradley PLC with manual joystick backup. It is supplied as standard with 110 gal tank line system that has output capacity of 4,000-6,000 lb per 8 hr shift. Process program handles up to 3 loads concurrently, with cycle time of 28 min.

RedEye RPM
Eden Prairie, MN 55344
Jan 14, 2008 As part of rapid prototype service, Ready Part(TM) finishing service produces smooth finish and watertight seal on acrylonitrile butadiene styrene (ABS) parts. Technology also prepares models for painting, plating, and post-finishing processes, as well as for use as master for room temperature vulcanization (RTV) molding. Parts are produced on FDM and PolyJet systems.

OMAX Corp.
Kent, WA 98032
Dec 12, 2007 Model 60120 JetMachining® Center abrasive waterjet cuts ceramics, composites, glass and stone, aluminum, tool steel, stainless steel, and titanium with accuracy of motion up to .003 in. It calculates velocity of tool path at over 2,000 points per inch, allowing for complete control over motion of abrasive jet. Unit features Compute First - Move Later motion control technology, abrasive feed system, MAXJET® 5 Diamond Nozzle Assembly, and ultra-high pressure direct drive pump.

Dow Corning Corp.
Midland, MI 48686 0994
Dec 06, 2007 Designed to automotive engine temperature, fuel, and oil resistance specifications, Silastic® 100% Fluoro Liquid Silicone Rubber (F-LSR) enables parts to operate consistently while in contact with aggressive fuels, chemicals, lubricants, and oils. Parts manufactured with this fully fluorinated, 2-part solution can also withstand temperatures from -60 to +220°C.

Blow Molded Specialties
Pawtucket, RI 02860
Nov 30, 2007 Manufactured to specification with smooth surface finish and sealing surface, Custom Molded Bottles and Containers come in 4 ml to 4 l sizes with 0.010-0.100 in. walls and ±0.005 in. tolerances, depending on shape and material. Products can be molded to fit into instrument cavities, incorporate complex neck shapes, and snap together. Variety of materials are available, including polysulfone, polyphenolsuflfone, polycarbonate, Hytrel®, PETG, and commodity resins.

Photo Sciences, Inc.
Torrance, CA 90505
Nov 20, 2007 Multifaceted microlithography techniques pattern photoimageable color polymer-coated substrates using direct-write laser, direct-write e-beam, optical reduction, and full field exposure lithography. Photoimageable color polymers provide means of producing microscopic patterns in various standard colors as well as custom polymer colors. Line widths can be produced as small as 2 microns in color polymers, offering compatible with nanoscale applications.

Silterra Malaysia Sdn Bhd
Kedah Darul Aman   Malaysia
Nov 09, 2007 Suited for devices used in construction of TFT panels, 0.16 µm High Voltage Technology features 3.17 µm² SRAM bitcell which facilitates high density embedded memory design in display driver for QVGA (240 RGB x 320) and WQVGA (320 RGB x 432, Wide-Quarter-VGA) TFT panels. Technology offers asymmetry high voltage well for denser design, one-time-programmable cell for gamma color tuning, ESD protection, and metal capacitors design guidelines.

Norplex Micarta
Postville, IA 52162
Nov 02, 2007 Composed of electrical grade epoxy resin combined with woven glass substrate, NP511B can be molded in conjunction with abrasion-resistant substrates such as Kevlar(TM) or Nomex(TM) to minimize or eliminate surface wear damage to copper and steel components in generators. Non-brominated resin system offers mechanical strength at temperatures to 170°C. When cured properly, NP511B retains half of its room temperature flexural strength at temperatures to 150°C.

Tri-Mack(TM) Plastics Manufacturing Corp.
Bristol, RI 02809
Oct 22, 2007 Tri-Mack Maxton® H-3 is thermoplastic friction/wear material for producing journal- and plane bearings, vanes, seals, thrust washers, piston rings, and related parts. Able to be custom molded and machined with ±.0005 in. tolerance in complex shapes from 1/8 x ¼ in. up to 24 in. dia., material exhibits 26,400 psi flexural strength, 17,800 psi tensile strength, 3.9 psi x 106 flexural modulus, 2.9 W/MK thermal conductivity, and is non-abrasive for use against stainless steel and aluminum.

austriamicrosystems AG
Premstatten   Austria
Oct 19, 2007 Based on Cadence v5.1.41, HIT-Kit v3.72 provides users with industry benchmark design environment for 0.35 µm High-Voltage CMOS process H35. It includes periphery cell libraries up to 50 V as well as set of 20 V devices optimized for power management products and display drivers in battery-powered applications. Along with circuit simulation models, features include design utilities such as SOAC tool, automatic layout generators, and guard-ring generation.

Makino Inc.
Auburn Hills, MI 48326
Sep 28, 2007 Designed for shops manufacturing parts for aerospace, medical, and injection mold markets, SP and U series Wire EDMs feature SurfaceWIZARD(TM) technology that is suited for use in poor flushing conditions where nozzles cannot be sealed on work surface. SurfaceWIZARD is developed for tool steels up to 4 in. thick, eliminates witness lines, supports 0.008 and 0.010 in. dia wires, and maintains part straightness within 5 and 2.5 microns in 1- and 2-pass machining, respectively.

Johnson Controls GmbH
Burscheid 51399  Germany
Sep 21, 2007 PP Thin Film method consists of composite foil comprised of multiple, primarily polypropylene layers in direct mold-behind process. Degree of glossiness can be varied and scratch-resistant films can be adapted to match finish of adjacent parts. Enabling production team to monitor wall thickness and reduce material consumption, one-step RIM alpha surface technology process allows strategic surface weakening to be included to accommodate airbag openings.

Applied Plastics Co.
Norwood, MA 02062
Sep 07, 2007 Developed for motors, stators, and gyroscopes, Stacking and Coating Service holds lamination alignment to within ±0.0005 in. and includes deburring and application of blue epoxy coating from 0.002-0.005 in. thick in one pass. Suited for laminations from 3/8-8 in. OD, smooth finished parts offer electrical resistance up to 1,000 V/mil and help prevent wire cuts and shorts. Metal laminations, bobbins, and end caps can be made from Arnon 7 high carbon steel or Magnesil.

Photo Sciences, Inc.
Torrance, CA 90505
Aug 24, 2007 Using photo chemical milling process, Photo Sciences can etch holes as small as 2.5 µm completely through thin sheets of metal. Etched features on metal parts have smooth, well-defined edges, making them suited for deposition masks or as apertures for optical applications. Chemical milling process specifically allows sub micron tolerances and complex patterns, which can be combined with in house design, CAD, and photo tooling capabilities.

Rogan Corp.
Northbrook, IL 60062
Aug 20, 2007 Liquid silicone rubber (LSR) used in molding service molecularly bonds with thermoplastic substrate parts. To eliminate handling and assembly of individual rubber and plastic components, tooling and overmolding techniques allow consolidation of silicone rubber and plastic into single composite part. Utilizing LSR's heat and chemical resistance, memory, and biological inertness in form of molecular-bondable material lets designers develop components that meet performance requirements.

Elma Electronic Inc.
Fremont, CA 94538
Aug 15, 2007 Suited for medical products, industrial enclosures, and various commercial applications, Type 35 Variety Case allows exact sizing of enclosure. Aluminum extrusions are cut to any specified length, and can accept tapped strips, sealing cords for EMC, optional direct mounting of panel or PCB, grounding terminals, or screws. Enclosures have conductive inner surface and sufficient contact points for EMC, and removable side panels that allow access to inside components.

ON Semiconductor, LLC
Phoenix, AZ 85008
Aug 14, 2007 HighQ(TM) copper on silicon integrated passive device (IPD) manufacturing services are available for those with ready-for-production product and those needing custom product designs. This 8 in. wafer technology, for production of passive devices used in portable and wireless applications, offers thick copper inductors, MIM capacitors (0.62 fF/µm²), and TiN resistors (9 W/square). Products withstand -65 to +150°C temperature cycling and can operate in 150°C for up to 504 hr.